NEEWER RP18-B LED Ring Light 18 Inch Dimmable Studio Light Instruction Manual

RP18 B LED Ring Light 18-Inch Dimmable Studio Light
Instruction Manual

Document Information
© 2021 Shenzhen Neewer TechnologyCo., Ltd. All Rights Reserved. This document is the sole property of Shenzhen Neewer TechnologyCo. Ltd and shall not be, reproduced. transmitted, transcribed. stored in a retrieval system or translated in any form, by any means, without prior written permission from Shenzhen Neewer Technology Co., Ltd. Shenzhen Neewer TechnologyCo., Ltd reserves the right to change the content in this instruction manual at any time and without prior notice.

Version Control

Functions

Power Supply

**** only ONE battery is used, and the brightness of the light will be decreased due to insufficient power.

Adjust the Brightness of Warm Color & White Color

Warm Color Slide the ON/OFF button to the ON position, then rotate the left knob in the picture to adjust brightness from 0% to 100%.

Cold Color Slide the ON/OFF button to ON position, then rotate the right knob in the picture to adjust brightness from 0% to 100%.

Install the ring light

1. Light adjustment Knob
2. Stand adjustment Knob| Mount the converter base onto the stand, then rotate the © Stand adjustment screw clockwise until it’s locked.

Rotate 0 Light adjustment screw until the light body is loosened, then the light can be adjusted to different angles.| Finally, rotate the 0 Light adjustment clockwise until the light is fixed.

Install the converter base

OFixing Knob ®AngleAdjustment Knob et Base Fixing Knob| Insert the OO Fixing Knob into the socket on your camera, then rotate it clockwise until your <a meta Is secured on the base.

Rotate the ®Angle Adjustment Knob clockwise until the camera is completely locked in.| Mount the converter base onto the hot shoe on the light, and rotate the 0) Base Fixing Knob clockwise until it’s locked.

Install the phone holder

1. Fixing Knob
2. Angle Adjustment KnOb
3. Base Fixing Knob| Insert the ® Fixing Knob into the Mount the converter base onto socket on phone holder, then the hot shoe on the light, and rotate it clockwise until the phone rotate the Oa Base Fixing Knob holder is sewed on the base.

Mount the converter base onto the hot shoe on the light, and rotate the ® Base Fixing Knob clockwise until it’s locked.| Finally, rotate the ®O Base Fixing Knob clockwise until it’s locked and put your cell phone onto the holder.

Setting up the remote control

Turn on the Bluetooth remote control| Turn on the Bluetooth on your  phone

Then find a Bluetooth device control. phone. called “AB Shutter3” and connect it to your cell phone.| Finally, enter the camera app on your phone to take pictures.

**** If the indicator on the remote doesn’t light up, please check if the battery cover is loose or if batteries need to be replaced.

Caution

• Please do not look directly at the light to avoid visual impairment
• Please do not reconnect the power cable in case of a safety hazard
• Please do not dismantle or modify the circuit of the item (unless professionally certified)
• Please use the power adapter included in the package or other certified power adapters.
• Please do not use alcohol or liquids to clean the light to prevent product damage.
• Please do not hit or drop the light
• Please do not expose the item to the sun for a long time
• Please unplug the power cable when the product is not in use
• Please use a soft cloth to clean the light
• Failure to comply with the items listed above will void the warranty.

Product  Parameters

FCC Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receive
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that a 20cm separation distance will be maintained between the device (excluding its handset) and users.

Shenzhen Neewer Technology Co., Ltd.
Room 1903, Block A, Lu Shan Building No. 3023
Chunfeng Rd Luo Hu District. Shenzhen
Guangdong 518001, China

Lingfeng Electric UK Ltd International House, 10 Churchill Way, Cardiff, CHO 7HE, United Kingdom

NW Formations GmbH(for authorities only) Hofersuasse 9B, 71636 Ludwigsburg. Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>