NEEWER RGB480 Smart Metal LED Light Instruction Manual
- June 5, 2024
- NEEWER
Table of Contents
RGB480 Smart Metal LED Light
Instruction Manual
Copyright
© 2021 Shenzhen Neewer Technology Co., Ltd.
All Rights Reserved. This document is the sole property of Shenzhen Neewer
Technology Co., Ltd and shall not be, reproduced, transmitted, transcribed,
stored in a retrieval system, or translated in any form, by any means, without
prior written permission from Shenzhen Neewer Technology Co., Ltd. Shenzhen
Neewer Technology Co., Ltd reserves the right to change the content in this
instruction manual at any time and without prior notice.
Version Control
| Date | Version number | Description | Issued by |
|---|---|---|---|
| 12/30/2021 | 1.0 | Smart Metal LED | |
| Light Manual | NEEWER° |
Functions
I Mode Short press the mode /channel button to switch from CCT, HSI, to Scene
mode.
I Left knob”HSI” Short press the Left Knob”HSI” to switch scenes, then rotate
the knob to adjust parameters.
Control Panel
Display
Models
CCT
Short press the “MODE/CH.” button until the symbol “CCT” shows on the display.
Next, you can rotate the Left Knob “HSI” to change the color temperature from
3200K to 5600K. Turn the Right Knob”BRR” to adjust light intensity from 0% to
100%.
HSI
Short
press the “MODE/CH.” button until the symbol “HSI” shows on the display. Next,
rotate the Left Knob”1-151″ to adjust the hue angle of the light(0*-360°). In
HSI mode, short press the Left Knob-HSI” to switch between the hue and
saturation settings. The hue and saturation level can be adjusted by long
pressing the Knob. The saturation value ranges from 0 to 100 (100 for 1:10
SCENE
Short press the “MODE/CH.” button until the word “SCENE” appears on the
display. Next, you can pressor rotate Left Knob”HSI” to switch scenes. Turn
the Right Knob”BRR” to adjust light intensity from 0% to 100%.
Available Scenes are as follows:
A. Police car
B. Ambulance
C. Fire truck
A. Fireworks
B. Party
C. Candlelight
A. Lightning
B. paparazzi
C. Screen
Control The LED Light Via APP
The ‘NEEWER” APP can be used to control the light through the Bluetooth
feature of your mobile. Scan the
When “ ” stops flashing, it indicates that the Bluetooth connection has been
established.
Installation Procedures
Install the diffuser
- DiffuserClasp
- Diffuser
With the light facing toward you, insert the 2 diffusers into the light body from its right side until it reaches the metal slot on the left. Then,pull up the 0 diffuser clasps on both sides to hold it in place.
Installation Procedures
Attach the U-shaped Bracket Install the barndoor
Attach the U-shaped Bracket on the 0 Screw LED light using the
securing knobs Screw Nut and washers supplied.
- Screw
- Screw Nut
Place the four 0 screw nuts into the screw holes of the light
body and turn them clockwise one by one until they are tight.
Put the barndoor on top of the light and make sure the screw holes at its four
corners are aligned to the Q screw nuts.
Insert the four e screws into the Q Close up the barn doors on the four screw
nuts and twist clockwise to the sides.
tighten them one by one.
close up the barn doors on the four sides
Mounting the light on a stand and adjusting barn doors
Turn
the securing knob of the stand counterclockwise until it is loosened.
Insert the stand into the connector of the light and turn the
securing knob clockwise until it is tight.
Turn the securing knob on both sides of the light until the light body is loosened.
Adjust the light body to your desired position.
Caution
- Please do not stare at the light directly while it is in use, or there might be a risk of visual impairment.
- Please do not cover the heat dissipation holes on the product with cloth or other items, to reduce the risk of product damage
- Please do not touch the light with wet hands as this poses a safety hazard
- Please do not dismantle or modify the circuit of the item (unless professionally certified).
- Please do not expose the item to the sun for a long time.
- Please turn the product off when it’s not in use.
- Failure to comply with the operation procedures and warnings listed in this manual will void the warranty.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital devices, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that a 20cm separation distance will be maintained between the device (excluding its handset) and users.
Shenzhen Neewer Technology Co., Ltd.
Room 1903, Block A, Lu Shan Building No. 3023
Chunfeng Rd Luo Hu District, Shenzhen
Guangdong 518001, China
**** Lingfeng Electronic (UK) Ltd
International House, 10 Churchill Way, Cardiff, CF10 2HE,
United Kingdom
NW Formations GmbH(for authorities only)
Hoferstrasse 9B, 71636 Ludwigsburg, Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>