FEIT LAN13 RGBW Inch smart coach Lantern User Guide
- June 5, 2024
- Feit
Table of Contents
FEIT LAN13 RGBW Inch smart coach Lantern
PRODUCT
FEATURES
| Part | Description | Quantity |
|---|---|---|
| A | 13 in. Lantern | 1 |
| B | Fixture Mounting Screws | 2 |
| C | Decorative Nuts | 2 |
| D | Rubber Washers | 2 |
| E | Junction Box Mounting Screws | 2 |
| F | Wire Nuts | 3 |
| G | Mounting Plate | 1 |
HARDWARE INCLUDED
INSTALLATION INSTRUCTION
- TURN POWER OFF
- Turn power off at circuit breaker or remove the correct fuse.
- REMOVE THE MOUNTING PLATE
- Unscrew the decorative nuts (C), remove the washers (D) and save them for the fixture mounting. Remove the mounting plate (G).
- Unscrew the decorative nuts (C), remove the washers (D) and save them for the fixture mounting. Remove the mounting plate (G).
- INSTALL MOUNTING PLATE
- Feed wires from junction box through mounting plate (G).
- Secure the mounting plate to the junction box by inserting the two junction box mounting screws (E) through the slots in the mounting plate that best align to the junction box.
- Feed wires from junction box through mounting plate (G).
- CONNECT WIRES
- Connect the green/yellow fixture wire and the green or bare copper house wire to the the green GND (Ground) screw on the Mounting Plate (G). Use the wire nuts (F) provided to connect the white fixture wire to the neutral supply wire and connect the black fixture wire to the live wire. Gently fix all wires into the junction box.
- MOUNT FIXTURE
- Insert fixture mounting screws (B) through holes on the fixture back plate. Add rubber washers (D) and secure fixture to mounting plate by tightening decorative nuts (C).
- Insert fixture mounting screws (B) through holes on the fixture back plate. Add rubber washers (D) and secure fixture to mounting plate by tightening decorative nuts (C).
- SEAL THE FIXTURE
- Caulk between the fixture back plate and the wall surtace to prevent water penetration. Use a silicone sealant (not included).
- TURN POWER ON
- Turn power on at circuit breaker or replace the fuse.
IMPORTANT WIRING INFORMATION
Always follow the recommended wire strip lengths and wiring combinations when
connecting wires. Hold stripped ends next to each other and align frayed
strands (do not twist wires). Push wires firmly into wire nut. Using your
fingers, twist wire nut clockwise until tight. Check for tightness by pulling
wires.
Getting Started:
-
* Download the Feit Electric app on your smart device.- After hardwiring to power, turn on your Smart Coach Lantern. The Smart Coach Lanterm must be blinking rapidly to pair. If not already blinking, push the reset button at the bottom of the back plate three times. The Coach Lantern will blink rapidly to indicate a successful reset and will initiate pairing mode.
- Open the Feit Electric app to complete the set up. Ensure Bluetooth is enabled on your phone. Tap Add Device or the + sign. The device name(s) will pop up on the Feit app. Tap on Go to add, then select the device to add. You will be prompted to enter your Wi-Fi network name and password.
- (Optional) Connect to Google Assistant or Alexa using the in-app quide.
Operation without connecting Smart Wi-Fi
If you power on and operate the Coach Lantern without connecting to Wi-Fi it will blink rapidly for 3 minutes then turn on and stay a Warm White light. Works with light switch.
LIMITED WARRANTY
This product is warrantied to be free from defects in workmanship and materials for up to 3 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at feit.com/help for help. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRAN TY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
WARNING: Risk of fire.
Use only on 120 volt 60Hz circuits. Before installing your lighting fixture, thoroughly review enclosed installation manual. If you do not have sufficient electrical wiring experience, please refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician. Do not use with standard dimmers. All electrical connections must be in accordance with Local and National Electrical Code (NEC) Standards. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
Supplier’s Declaration of Conformity:
- 47 CFR $ 2.1077 Compliance Information
Responsible Party:
- Feit Electric Company
- 4901 Gregg Road;
- Pico Rivera, CA 90660, USA
- 562-463-2852
Unique ldentifier:
LAN13/RGBW, ITM. / ART. 1613106
FCC Rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660. www.feit.com CAN ICES-005 (B)
Need Help?
- Thank you for your purchase.
- Questions, comments or feedback?
- We’d love to hear from you.
- Visit feit.com/help for support or connect with us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>