BLUEWEAR 004653-004657 Safety Helmet Instruction Manual

Safety Helmet
Instruction Manual

004653-004657

SAFETY HELMET
OPERATING INSTRUCTIONS Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions).
Jula reserves the right to make changes, For latest version of operating instructions, see www.jula.com

SAFETY INSTRUCTIONS

• This industrial safety helmet 004653-57 is primarily intended to protect the wearer from head injuries and brain damage as a result of falling objects in an industrial environment. See the warnings and instructions for correct usage.
• Be aware that no safety equipment can provide full protection — always act carefully and exercise sound judgment when work involves risks.
• The helmet is only intended to protect the head of the wearer by reducing and distributing the force of falling objects from above that hit or penetrate the shell of the helmet. The helmet is not intended to provide protection from impact or penetration on the sides of the shell or to the face or neck, even if it does provide some protection from light knocks and blows in these areas.
• Never modify the helmet in any way or remove any components, unless recommended by the manufacturer—this can reduce the safety function of the product. Never attempt to adapt the helmet to mount accessories, unless recommended by the manufacturer.
• Do not use paint, solvent or glue on the helmet, or put stickers, etc. on it, unless recommended by the manufacturer.
• The shell of the helmet and the lining are intended to be damaged or partially destroyed when subjected to impact—thus absorbing the impact energy and protecting the wearer of the helmet. A helmet that has been exposed to severe impact should therefore always be replaced, even if there is no visible damage.
• Do not let the helmet touch live equipment or expose it to temperatures lower than —25°C or higher than 150°C.

SYMBOLS

| Conforms with the requirements in the relevant EU directives.
---|---

“REGULATIONS AND STANDARDS”

• (EU) 2016/425 — Regulation for personal protective equipment (PPE).
• EN 397:2012 + Al — Safety helmets.

TECHNICAL DATA

This product is CE marked to demonstrate compliance with the EU directive for personal protective equipment (EU) 2016/425.
Notified Body: 2754 AUENOR CERTIFICATION ZA DU SANITAL 21 RUE ALBERT EINSTEIN 86100 CHATELLERAULT France.

ASSEMBLY

1. Turn the helmet upside down. Place the liner in the helmet with the forehead pad facing forward. The shock-absorbing insert should remain in the shell.
2. Bend each suspension hook outwards at its joint and insert in the corresponding slot. Press the hook firmly to lock in place. Repeat for all hooks.

ADJUSTING
To provide proper protection the helmet must be adjusted to fit the head of the user.
Vertically
The headband can be lifted or lowered at both the front and back by moving the suspension hooks on the liner.

1. Remove the liner from the helmet by pulling the suspension hooks until they click out from their slots.
2. Turn the suspension hooks 90° in either direction until the hole in the hook is in line with the fastener on the headband. Pull the hook off the headband.
3. Move the hook to the required position.
4. Turn the hook 90° in relation to the headband until the hook locks in place.
5. Repeat steps 2 to 4 for the other hooks.
6. Replace the liner in the helmet.

CIRCUMFERENCE OF LINER
Adjusting knob with lock function. 1. Turn the knob anticlockwise until the headband has opened to its maximum circumference. 2. Put on the helmet and turn the knob clockwise until the headband fits firmly and comfortably.
NOTE:
Do not over tighten.

USE

CHECK BEFORE USE
Always check before use that the helmet is in good condition without any nicks, marks, cracks, splinters or other damage and that no parts are missing or damaged.
WARNING! To ensure that the helmet provides full protection and has not deteriorated with age it should be inspected every month in accordance with the manufacturer’s instructions. This inspection should be carried out by a person familiar with personal safety equipment.

RESCUE DURING ACCIDENT
Plans for rescue operations in the event of an accident should be prepared before and during use.

MAINTENANCE

CLEANING

• Clean the helmet after use.
• Clean the helmet with lukewarm water and a mild detergent. Do not use paint, solvent-based detergent, chemicals, glue, petrol, etc. on the helmet. Such products can reduce the safety function of the helmet without being noticed or otherwise apparent to the user.

STORAGE
Store the helmet in a cool, dry, and clean place, protected from direct sunlight. Avoid storing in hot or humid places, or where there is oil, oil mist, or other degrading substance.
USEFUL SERVICE LIFE
The helmet can be used for 5 years or longer, as long as it is not subjected to impact or damaged in any other way.

REPAIRS AND REPLACEMENT
Repairs must be carried out according to the manufacturer’s instructions — no departures or modifications are acceptable. If the helmet shell or liner is damaged it must be unconditionally replaced. Attempts to repair them are unacceptable. Suitable accessories and spare parts for this helmet: Mesh visor 004508-09-2, helmet-mounted ear protectors 005608-09-1.
WARNING!
A helmet that has been exposed to impact should be unconditionally discarded and replaced with a new one, even if there is no visible damage.
TRANSPORT
There are no special requirements concerning packaging and transport, but a transport bag is available as an accessory.

EU DECLARATION OF CONFORMITY
Item number.
004653, 004654, 004655, 004656, 004657
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the manufacturer.,
SAFETY HELMET
004653 – RED.
004657 – ORANGE, ORANGE, ORANSJE,
Conforms to the following directives, regulations, and standards:,

The PPE is identical to the PPE which is subject of EU type-examination certificate No:| 2754/2169/158/09/18/0645
---|---
Name and address of the notified body involved:| ALIENOR CERTIFICATION ZA DU SANITAL 21 RUE ALBERT EINSTEIN 86100 CHATELLERAULT France NB 2754

This product was CE marked in a year:

JULA AB, BOX 363, SE-532 24 SKARA
2021-12-30
©Jula AB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>