BRANDMOTION SUTV-8849 Adjustable Rear Vision System Instruction Manual

BRAND MOTION SUTV-8849 Adjustable Rear Vision System

Overview

Kit A Components for installing the SUTV-8849

Kit Contents:

1x CMOS Camera

1x Adjustable 5th Wheel Camera Mount
1x Video Chassis Harness
1x RCA to Factory 22 Pin connector
3x Push Nuts
15x Zipties
1x Dual Camera Interface

Recommended Tools

Access the Radio

Preparing the Radio

1. First, you need to gain access to the back of your aftermarket radio. If you already have access, skip to part 2.
2. Start by removing the rubber bin insert from the top of the dash
3. Remove the 7mm bolt under the rubber bin insert.
4. Using a plastic trim removal tool, remove the window switch panel.
5. Disconnect harness from window switches.
6. Remove the 7mm bolt behind the window switch panel.
7. Remove driver knee bolster cover
8. Remove (2) 7mm bolts on both sides of the steering column.
9. Remove center stack/cluster trim
10. Remove the glove box for access. You will need access to the area behind the glove box to make your connection to the radio.
11. Remove (4) 7mm bolts to remove radio from dash

Install the Video Interface

Module Configuration

Before Installing:

• Disconnect the negative battery terminal before beginning installation!
• DIP Switches must be set before installation of the interface module!
• For vehicle-specific instructions for dash disassembly, reference the workshop manual.

Part 1

Power and Signal Connection

BACKUP CAMERA ADD-ON
IMPORTANT NOTE: SET DIP SWITCHES BEFORE PROCEEDING

Part 2

Programming & Connections

THE VEHICLE MUST PERFORM TWO FULL POWER CYCLES FOR SUCCESSFUL PROGRAMMING

Note:
If only adding a rear camera, output from the camera can be connected directly to CAMERA IN” on the vehicle-specific T-Harness.

Part 3

Part 4

Camera Operation

IMPORTANT NOTES

• If camera functionality is tested without a camera(s) fully powered and connected, the system may display a “Camera not Available” message and will temporarily disable camera input. Allowing the vehicle to sit for 5 minutes with the ignition off will reset the function.
• The display may stay in reverse camera mode until the vehicle is driven to 7MPH. This is a factory function and cannot be changed.
• The module must remain installed for proper operation.

Manual Activation

• The green manual activation wire can be connected to +12V or Ground to manually activate the secondary camera. This can also be adjusted to only recognize either using the ARC 357 PC Configuration Tool.
• Blind Spot mode will automatically activate the aux camera with the right blinker in compatible vehicles. If your vehicle is not compatible, you will need to use the manual trigger wire. Make sure Blind Spot activation is turned on using the ARC 357 PC Configuration Tool. By default, this feature is turned off in Firmware 1.9 and newer.

Before Installing:

• Disconnect the negative battery terminal before beginning instllation!
• DIP Switches must be set before installation of the interface module!
• For vehicle-specific instructions for dash disassembly, reference the workshop manual.

Default Auxiliary Camera Behavior

Install Rear Camera

Part 1

Camera functionality test (Highly recommended, not required)

1. 8837:
   • There will be three wires accompanying the RCA: Red, Green, and Black
   1. Twist red and green together = Power
   2. Black = Ground
   • Using a wire extension (not supplied)
   1. Connect twisted red and green directly to the positive terminal of the battery
   2. Connect Black to the negative terminal of the battery
   • Test Camera
   1. Connect RCA to Aftermarket radio and
   2. Turn Key to on position
   3. Place the vehicle in reverse and verify a good image.
2. 8847:
   • There will be two wires at the rear of the harness near the camera
   1. Red= Power
   2. Black = Ground
   • Using a wire extension (not supplied)
   1. Connect red wire directly to the positive terminal of the battery
   2. Connect Black to the negative terminal of battery
   • Test Camera
   1. Connect RCA to Aftermarket radio and
   2. Turn Key to on position
   3. Place the vehicle in reverse and verify a good image.
3. 8857:
   • There will be two wires accompanying the RCA: Red and Black
   1. Red= Power
   2. Black = Ground
   • Using a wire extension (not supplied)
   1. Connect the Red wire directly to the positive terminal of the battery
   2. Connect Black to the negative terminal of the battery
   • Test Camera
   1. Connect RCA to Aftermarket radio
   2. Turn the Key to on position
   3. Place the vehicle in reverse and verify a good image.

Part 2

Installing Rear Camera on Tire Carrier

1. Remove your spare tire and place the camera bracket on the top two studs.
2. Secure bracket to carrier using (2) push nuts to secure the bracket on two top studs.
3. The nylon washer will go on the bottom stud and will be secured with the third push nut.
4. Place your tire on the carrier and make any needed adjustments to the camera placement to see through the wheel spokes.
5. Once the orientation is satisfactory, tighten two adjustment screws on bracket.
6. Reinstall the spare tire on the carrier.

Install Rear View Camera Chassis Harness

1. Using a plastic trim removal tool, remove interior panels on the inside of the rear gate

2. Insert the camera connector through the rear relief/vent flap behind the spare tire mount. DO NOT RUN THROUGH THE CENTER HOLE OF THE TIRE CARRIER

3. Gently pull the harness through the relief door and connect your camera harness to your chassis harness.

4. Use supplied wire ties to secure chassis harness to existing harness in the tailgate.

5. Use supplied wire ties to secure the chassis
   harness to the exterior of the fabric factory wire cover connecting tailgate to the body. Do not run through fabric factory wire cover. CAUTION: Leave enough slack to allow the gate to open fully

6. Using a plastic trim removal tool, remove the rear access (behind seat belt) panel to expose 10mm bolt, and remove bolt. Failure to remove this bolt will break the panel.

7. Remove the interior rear quarter panel

8. FOR 8848, you will need to ground black wire at a good chassis ground. Isolate the red wire with electrical tape. You will connect to power at the front of the vehicle in later steps.

9. Pull back the carpet and continue running chassis harness forward under sill plates and B-pillar cover to passenger kick panel

10. Use a plastic trim removal tool to remove the (2) plastic push pins and remove the passenger sill plate/kick panel.

11. Run the chassis harness behind the glove box and into the radio cavity.

Connecting to Power

1. 8837:
   • There will be three wires accompanying the RCA in the passenger kick panel: Red, Green, and Black
   1. Twist red and green together = Power
   2. Black = Ground
   • Identify power output from your aftermarket radio
   • Connect twisted red and green wire to power output from radio
   • Connect black wire to Chassis ground. We recommend using factory chassis grounding point.
2. 8847:
   •  Identify red power wire exiting the back of the yellow RCA from your camera chassis harness
   • Identify power output from your aftermarket radio
   • Connect Red wire to power output from your aftermarket radio
   • Connect black wire to Chassis ground. We recommend using factory chassis grounding point.
3. 8857:
   • Connect jumper power harness to chassis harness (if not already connected)
   • Separate power and ground wires at jumper harness
   1. Red = Power
   2. Black = Ground
   • Identify power output from your aftermarket radio
   • Connect red wire to power output from your aftermarket radio.
   • Connect black wire to Chassis ground. We recommend using factory chassis grounding point.

Kit Contents

Part 1

Install Forward Facing Camera

1. Power the camera harness with 12V, connect the camera to the harness and plug the Yellow RCA into the video in port to test the camera functionality.
2. Route the harness away from any moving parts so the harness will not get cut. Enter the underhood area and secure to the harness running along the driver’s side fender with zip ties.
3. Route the camera harness into the vehicle’s interior through the factory grommet in the firewall on the driver’s side.
4. Route the harness to the back of the radio where the display interface will be.
5. We recommend connecting to 12V+ from a vehicle ignition source. The ground should be located on a chassis ground point.

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>