Whirlpool GMWL758IXLAUS Gas Cooking Appliance Installation Guide

June 6, 2024
Whirlpool

Whirlpool GMWL758IXLAUS Gas Cooking Appliance Installation

Specifications

  • Model : GMWL758IXLAUS
  • Gas type : Natural gas or Universal LPG
  • Dimensions : 730 mm x 510 mm
  • Clearance A : Minimum 600 mm for range hood, minimum 750 mm for exhaust fan

Product Usage Instructions

Installation

Ensure the removable panel is installed to prevent airflow from extinguishing the burner flame. Maintain required distances as specified in the manual. Follow instructions for installing a hood above the cooktop

Assembly

  • Clean the perimeter surface and apply the supplied gasket to the hob.
  • Position the hob in the worktop opening respecting the dimensions providedEnsure the power supply cable allows upward extraction.
  • Secure the hob using the provided brackets, fitted into  relevant bores and fastened with screws based on worktop thickness.

Gas Connection

Before installation, check gas type compatibility and supply pressure. Refer to the Injectors table for gas supply pressure values. Use appropriate adaptors and regulators for safe operation and efficient energy consumption.

PRODUCT DESCRIPTION

  1. Removable panstand grids
  2. Semi-rapid burner
  3. Rapid burner
  4. Semi-rapid burner
  5. Auxiliary burner
  6. 2 Crown burner
  7. Semi-rapid burner control knob
  8. Rapid burner control knob
  9. 2 Crown burner control knob
  10. Semi-rapid burner control knob
  11. Auxiliary burner control knob

Symbols

  • Shaded circle
  • Large flame
  • Small flame

Tap closed

Maximum opening/delivery and electric ignition Minimum opening or reduced delivery

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

  • Use protective gloves for handling, preparing, and installing the product.
  • This product can be embedded in a worktop 20 ÷ 60 mm thick.
  • If there is no oven beneath the hob, insert a separator panel with a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case, less than 20 mm from the bottom of the hob. If you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system.
  • Where the rating plate is obscured by cabinetry when the cooktop is in the installed position, place the duplicate rating plate (provided together with the literature) on a surface of the cabinetry adjacent to the cooktop.

NOTE: An airflow may extinguish the burner flame if the removable panel is not installed. The air flow may occur when you open or close the cabinet door or drawer.

  • An authorized person must install this appliance in accordance with this instruction manual:
  • AS/NZS 5601.1 – Gas installations (installation and pipe sizing)
  • Local gas fitting regulations
  • Local electrical regulations
  • Building Code of Australia and any other government authority.

DIMENSIONS AND DISTANCES TO BE MAINTAINED

NOTE: In case of installation of a hood above the cooktop please refer to the range hood instructions for the correct distance.
Clearance A, between the highest part of the highest burner of the gas cooking appliance and a range hood or exhaust fan (overhead clearance), shall be no less than 600 mm for a range hood, and no less than 750 mm for an exhaust fan.

  • The minimum clearance from a combustible surface shall be a 200 mm horizontal distance from the periphery of any gas burner (AS/NZS 5601.1)
  •  If that horizontal clearance is less than 200 mm, that vertical surface must be protected by a non combustible material for 150 mm above the cooktop surface across the entire length (depth, width).
  • The shown area indicates the protected surface, which may be ceramic tiles or other approved material.

The high from the worktop surface to the top of the pan support is 51 mm.

****

ASSEMBLY

After cleaning the perimeter surface, apply the supplied gasket to the hob, as shown in the figure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE : the power supply cable must be long enough to permit its upward extraction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures)

GAS CONNECTION

  • Before installation, check that the gas type (natural gas or Universal LPG) of the cooker is suitable for the gas type available for the installation.
  • Check that the gas supply pressure is consistent with the values indicated in the “Injectors table.” This will ensure the safe operation and longevity of your appliance while maintaining efficient energy consumption.
  • For ULPG models, the gas supply for the hotplate must be regulated to a pressure of 2.75kPa. The gas inlet connection fitting is 1⁄2” B.S.P female thread (in compliance with ISO 7 thread).
  • For NG models, the gas supply is connected to a regulator, which is supplied. The inlet connection has ½” B.S.P female thread. THE ELBOW ON THE APPLIANCE MUST BE HELD FIRMLY WITH A SPANNER. DO NOT OVER TIGHTEN. The regulated pressure for NG is 1.00kPa.
  • A manual shut-off valve must be installed in the gas line, in an accessible position external to the hotplate, so that the gas supply can be shut-off in the event of an emergency or service. For the appliance’s gas inlet position, refer to Fig. 1 for NG and Fig.2 for ULPG.
  • After installing the gas supply and making all connections check thoroughly for possible leaks. Turn all control knobs on the unit to the “OFF” position. Open the valve on the gas supply. Using a soap and water solution, check each gas connection one at a time by brushing the solution over the connection. The presence of bubbles will indicate a leak. Tighten the fitting and re-check for leaks. If it is not possible to correct the leak, replace the fitting. Under no circumstance use matches or flame for checking leaks.
  • Turn on the appliance gas cock and light each burner. Check for a clear blue flame without yellow tipping. If burners show any abnormalities check the following• Burner cap on correctly
  • Burner positioned correctly
  • Burner vertically aligned with injector nipple
    In some cases, the burners will fail to ignite immediately and seem to blow lightly when they do ignite; this is usually due to air in the gas pipe, which should clear itself within seconds of operation. If satisfactory performance cannot be obtained after following the instructions given, contact the local gas authority for advice and assistance.:

FAQ

Q: What should I do if the burner flame gets extinguished?
A: Ensure the removable panel is installed to prevent airflow disruptions. Adjust ventilation to avoid sudden airflows that can extinguish the flame.

Q: Can I use ceramic tiles as a protective surface near the gas burner?
A: Yes, ceramic tiles or other approved non-combustible materials can be used to protect vertical surfaces if the horizontal clearance is less than 200 mm.

Q: How do I know if the gas type of my cooker is suitable for installation? A: Check the product manual or contact the manufacturer to verify if your cooker supports natural gas or Universal LPG.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Whirlpool User Manuals

Related Manuals