BRESSER BR-22B Bi-Colour LED Ring Light Instruction Manual

BRESSER BR-22B Bi-Colour LED Ring Light

GENERAL WARNINGS

DANGER OF BODILY INJURY

• Do not use it in the presence of children or animals. Store out of reach of children and animals.

RISK OF MATERIAL DAMAGE

• Make sure that no one can trip over the connection cables of the device. The device could be knocked over.
• Only use the recommended power cable or the recommended battery for the power supply!
• The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!

DANGER OF AN ELECTRIC SHOCK

• This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK.
• Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat.
• Check this device, cables, and connections for damage before use.
• Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
• Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.

RISK OF GLARE

• Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

FIRE/EXPLOSION HAZARD

Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short-circuit the device or dispose of it in the fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!
• Only use the recommended power supply.

IMPORTANT NOTE

• Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary.
• Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation, and before any maintenance and cleaning work.
• Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the main supply.
• To disconnect the unit from the mains, always pull the mains plug and never pull the cable! Do not subject the device to excessive vibrations.

PRODUCT INFORMATION

• Thanks for choosing our Led Ring Light!
• The LED beads have less heat to increase their lifespan.
• The light shell is high-strength ABS, sturdy, durable, beautiful, and fashionable. It’s light and handy, simply designed, and easy to carry. Make the live show more effective.

PARTS OVERVIEW

1. Dimmer knob
2. When turned on, the brightness range is 10-100%
3. Color temperature adjuster
4. When turned on, the CCT range is 3000-6500K.
5. Vents
6. V-mount battery socket
7. Power switch
8. Cold shoe
9. Power socket
10. Power cable
11. Locking screw (tilt joint)
12. Tilt joint
13. Handle
14. Fixing screw (tripod connection)
15. Tripod connection

INSTALLING THE POWER CABLE

1. Insert the two-pin C7 plug of the power cable (➑) into the power connection socket (➐) on the ring light.
2. Insert the Euro plug of the power cable into the socket.

INSTALLING THE V-MOUNT BATTERY (optional)

1. Slide the fully charged V-mount battery* (type NP-F550 / 750/970) into the holder (➍) from the side so that the battery clicks into place.
2. To remove, slide the battery out of the holder in the opposite direction.

TURNING ON THE LED LIGHT

1. Establish the power supply for the device (insert battery or connect power cable).
2. Move the on / off switch (➎) to the ‘I’ position to switch the device on. The lighting is switched on with the settings of the last use.
3. Move the on / off (➎) switch to the ‘0’ position to switch off the device. The last settings made are retained until the device is switched on again.

Important: Disconnect the device from the power supply if it is not going to be used for a long period of time!

BRIGHTNESS ADJUSTMENT

1. Turn the dimmer knob (➊) clockwise to increase the brightness.
2. Turn the dimmer knob (➊) counterclockwise to decrease the brightness.

COLOR TEMPERATURE ADJUSTMENT

1. Switch on the device.
2. Briefly turn the color temperature adjuster (➋) to set the desired light temperature.

ADJUSTING THE TILT ANGLE

1. Hold the ring light and slowly loosen the locking screw for the tilt joint (➒).
2. Move the lamp head to the desired position and tighten the locking screw (➒) again hand-tight.

MOUNTING ON A TRIPOD (optional)

1. Loosen the fixing screw (⓬) for the tripod connection so far that the opening of the tripod connection is exposed.
2. Place the lamp with the opening of the tripod connection (⓭) on the spigot adapter of a tripod and tighten the fixing screw firmly.

Note: The ring light can also be held with the handle – if necessary by a second person. In this way, the lighting position can be changed quickly and easily.

ATTACHING ACCESSORIES (optional)

• The ring light has a so-called cold shoe, which can be used to attach a smartphone holder*, for example.

DISPOSAL

Dispose of the packaging materials properly, according to their types, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal. Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner. In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. The disposal of domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

1. battery contains cadmium
2. battery contains mercury
3. battery contains lead

TECHNICAL DATA

EC DECLARATION OF CONFORMITY

Hereby, Bresser GmbH declares that the equipment type with part number: F004593 is in compliance with Directive: 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/F004593/CE/F004593_CE.pdf

UKCA DECLARATION OF CONFORMITY

Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet address: www.bresser.de/download/F004593/UKCA/F004593_UKCA.pdf

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms. Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.

www.bresser.de/warranty_terms

Bresser UK Ltd

• ADDRESS: Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain.

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER
• index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>