eta 7762 90000 Aspira Vacuum Sealer User Manual

Aspira Vacuum Sealer

ASPIRA

USER MANUAL

Product images are for illustrative purposes only

INSTRUCTIONS FOR USE

Dear customer, thank you for purchasing our product. Please read the operating instructions
carefully before putting the appliance into operation and keep these instructions including
the warranty, the receipt and, if possible, the box with the internal packing.

I. GENERAL SAFETY INSTRUCTIONS

GENERAL PROVISIONS:

– Consider the instructions for use as a part of the appliance and pass them on to any other
user of the appliance.
– Check whether the data on the type label corresponds with the voltage in your socket.
The power cord plug may only be connected to the electrical socket complying with the
applicable standards.
– This appliance may only be used by children aged 8 years or older,
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be
made by children without supervision. Children younger than 8 years
must be kept out of reach of the appliance and its power cord.
– Do not leave the appliance running without attendance and check
it during the whole process of welding!
– Before replacing accessories or accessible parts, before assembly
and disassembly, before cleaning or maintenance, turn off the
appliance and disconnect it from the mains by pulling the power
cord from the power socket!
– Always unplug the appliance from power supply if you leave it
unattended and before assembly, disassembly or cleaning.
– Never use the appliance if the power cord or power plug are
damaged, if the appliance is not correctly operating or if it has fallen
on the floor and been damaged, or if it has fallen into water. In such
cases take the appliance to a professional service centre to verify
its safety and correct function.
– Pay careful attention when handling the appliance to avoid injury,
(e.g. burns).
– The appliance has a hot surface. Persons insensitive to heat must be careful when using
the appliance.
– When the appliance is in operation, prevent pets, plants or insects from getting in contact with it.
– The appliance is intended for home use and for similar purposes (in shops, offices and
similar sites, in hotels, motels and other residential premises, or in facilities providing bed
and breakfast service). It is not intended for commercial use!
– Do not plug the power cord in the electrical socket and do not unplug it with wet
hands or by pulling the power cord!
– Never immerse the appliance into water or any other liquid (even its parts)!
– Avoid contact with the sealing wire when hot.
– The producer does not undertake any responsibility for damage caused by improper use of the appliance (e.g. deterioration of food, injury, burning, scalding, fire, etc.) and its guarantee
does not cover the appliance in the case of failure to comply with the safety warning above.

USE OF THE APPLIANCE:

– After completion of the vacuum process leave the cover of the
appliance open for the welding part to cool down.
– CAUTION – The appliance is not designed for constant operation.
Do not use the welder constantly for longer than 15 minutes, then
leave it to cool down for approx. 10 minutes.
– It is not intended for outdoors use.
– The appliance must not be used in damp or wet environment and in any environment with
the danger of fire or explosion (spaces where chemicals, fuels, oils, gases, paints and
other flammable or volatile materials are stored).
– Do not seal fluids in liquid state with vacuum function. If you want to store liquid food
(such as soups), first freeze the food in an appropriate container, cut the food into pieces,
put in bags and seal/vacuum them. Put the individual bags into freezer.
– Do not place the appliance on unstable, fragile or flammable surfaces (e.g. glass, paper,
plastic, wooden varnished boards and various fabric/table cloths).
– Use the appliance in the working position only at places with no risk of turning over and in
sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable
objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, wash basins, etc.).

POWER CORD:

– If the power cord of the appliance is corrupted, it has to be replaced
by the manufacturer, its service technician or a similarly qualified
person so as to prevent dangerous situations.
– Never put the power cord on hot surfaces and never let it hang over table edge or worktop
edge. If the cord is caught or pulled, e.g. by children, the appliance may overturn and fall
down, causing a serious injury!
– The power cord must not be damaged with sharp or hot objects, open fire, it must not be
sunk into water or bent over sharp edges.
– In order to ensure safety and proper function of the appliance, use only original spare
parts and accessories approved by the manufacturer.
– Only use this appliance for the purpose it was designed for, as specified in this manual.
Never use the appliance for any other purpose.

II. DESCRIPTION OF THE CONTRO

A – bag sealer body
A1 – lid
A2 – handle + lid lock control
A3 – welding part
A4 – the sucking area
A5 – sealing gasket
A6 – airproof loop of sponge
A7 – port for external extraction

A8 – space for storage fo cable
A9 – hinged holder
A10 – compartment for vacuum bag roll storage
A11 – vacuum bag roll cutter
B – control panel
B1 – automatic vacuum button + welding button
B2 – welding button
B3 – PULSE button for controlled vacuum
B4 – external vacuum / marinate button
B5 – food type setting button (dry / slightly moist) // double weld function
B6 – double weld function indicator light
B7 – STOP button
B8 – LED display (time countdown of function duration)
B9 – signal lights for the selected type of food
B10 – button for setting the vacuum-packing intensity
B11 – signal lights for the selected vacuum-packing intensity
C – extraction hose
D – vacuum-packing box
D1 – release valve

Optional accessories:

Cling film: 3m long and 28cm wide – ETA176200010
Bags 30 x 40 cm (50 pcs) ETA176293040
Bags 25 x 35 cm (50 pcs) ETA176292535
Bags 20 x 30 cm (50 pcs) ETA176292030
Suction hose + Hose adaptor ETA076290020, intended for:
Reusable bags 10 pcs 23×21 cm; 10 pcs 23×28 cm; 5 pcs 30×28 cm ETA176290025
Vacuum-packing box (1x 670 ml + 1x 1360 ml) ETA076290030
Vacuum-packing box (1x 1000 ml + 1x 2000 ml) ETA076290040
Vacuum-packing box (1x 1350 ml + 1x 2570 ml) ETA076290050
Vacuum-packing box (2x 670 ml + 2x 1360 ml + 1x 1000 ml + 1x 2000 ml) ETA076290060
Note: the above boxes cannot be used for the marinating function
Extraction hose – ETA476200210, intended for:
Vacuum-packing box (capacity: 1000ml) – ETA476200200
Vacuum-packing box (capacity: 2000 ml) – ETA476292000

III. INSTRUCTIONS FOR USE

Remove all packaging materials and take out the appliance. Remove all adhesive foils,
stickers or papers from the appliance.

BAG SEALER FUNCTIONS

1. B7 STOP button
   It is used to stop the activated operation.

2. A B3 PULSE button for controlled vacuum
   It is possible to start and run vaccuming, which allows you to control the intensity of
   vaccuming. When you release the Pulse button, the backlight of the B2 button and the
   countdown on the B8 display will start flashing – if you are extracting air from the bag, you
   can now press button B2 and the bag will be sealed.

3. B2 sealing button
   When activated, the vacuum sealer will produce a strong, seamless seal.
   The function is indicated by the backlight of the button and a gradual countdown on display
   B8. Place the bag as shown in Figure 3A. The end of the function is signalled by the
   completion of the countdown and switching off the button backlight.

4. Automatic vacuum + welding button
   After the function is activated in a stand-by mode, the welding machine removes air
   by suction, and than creates a strong seamless joint. The function is signalled by the
   illumination of buttons B1 and B2. Place the bag according to Fig. 3B. The end of the
   function is signalled by the completion of the countdown and the switching off of the button
   backlight.

5. External vacuuming + marinating button B4 (vacuuming in the vacuum box)
   The button supports two basic functions:
   a) Evacuation of air from the vacuum box (short press, button backlight illuminates)
   It is used to extract air from the vacuum box using the suction hose. When activated, it
   sucks the air out of the vacuum box.
   b) Marinating function (long press to activate, button backlight flashes)
   Vacuuming opens the pores of the ingredients, thus considerably speeding up the
   marinating process from several hours to approx. 20 minutes. The program works in
   cycles in which it gradually extracts and releases air. Display B8 shows the number of
   cycles remaining. The program is designed to work with the vacuum box D.
   Press button B4 after connecting the hose to the external suction opening and then
   plugging it into the vacuum box. After switching off, remove the suction hose (first from the
   vacuum box).

Note
If you have purchased ETA boxes with an adapter (ETA076290020), its use is slightly
different – you insert the thin connector into the device itself and just attach the
extended circular part to the given suction point of the box or compatible bag – when
the function is activated, the circular part will attach itself.

Caution
– The correct function of the appliance is guaranteed only if you use the vacuum-packing
boxes supplied by the manufacturer. Request the vacuum-packing boxes from your
distributor.
– When removing food from the vacuum-packing box, make sure to release the vacuum
first by pressing down the valve D1 in the middle of the cover.

6. B5 button for selecting the type of food + double weld function
   It is used to set whether you wish to vacuum-pack dry food or moist food and for setting the
   double weld. The setting is indicated by the appropriate indicator light B9 and B6:
   = dry food
   = Moist food
   2x = The bag / foil will be welded in two welds

7. B10 button for setting the vacuum-packing intensity
   It is used to set the vacuum-packing intensity. The selected mode is indicated by the
   appropriate indicator B11:
   = Normal (faster extraction for normal vacuum-packing)
   = gentle mode (slower extraction for vacuum-packing of more fragile food)
   Standard operation
   Plug an appliance in. Set the type of food according to the chosen ingredient.

Than proceed according to the instruction in the picture 2-4:

1. Lift the lid A1 up by pressing and lifting the handle A2, which controls lid arrestation.
2. When you are making a bag from the vacuum bag roll (none of the two ends sealed),
place it in the compartment for vacuum bag roll storage and prepare and cut the required
length according to Fig. 5. Then place one end of the cut part on the welding part and
weld, see function 3) with button B2. Fill the bag with the required ingredient, insert the
end of the bag into the suction area (if you want to evacuate) or the welding area.
3. Close the lid A1 and then the handle A2 (fig. 4). This secures the lid.
4. Press the button with the required operation (B1, B2 or B3). The function is signalled by
the illumination of the button or by a gradual countdown on the B8 display.
5. When the appropriate button light goes out, the operation has been completed.
You can now open the cover A1 and remove the film/bag.

Notice
– Proper functionality of the appliance is assured only when using the foils/bags
supplied by the manufacturer. Request these foils at your retailer. Do not use plastic
bags. At the same time you can re-weld many foods in their original packaging (eg
bags of potato chips).
– The vacuum sealer is used to seal cling foil up to the max. width of 300 mm.

IV. CARING FOR YOUR VACUUM SEALER

Do not clean appliance if is hot. After each use, wipe the outer parts with a damp soft
cloth. To clean the inner parts of the appliance, wipe all pieces of food and liquids with
a paper cloth. Leave to dry properly before next use. Do not use abrasive and aggressive
cleaning agents! If the power cord becomes stained, wipe it with a damp cloth. The colour
change of the surface in time is normal. This change does not change the qualities of the
surface in any way and is not a reason to return this appliance! If particles of plastic adhere
to the sealing wire, wipe them off carefully to avoid damage to the wire. If can help to carry
out a sealing operation the lid and pressing fully down without a bag in position. This will
heat the wire and soften any plastic adhering to it.

BAGS
Before reusing a bag, we recommend properly washing it in warm water with a small
amount of dishwasher detergent, and rinsing in clear water.

Place the bag so that water can flow out from inside the bag. Before reusing, dry the bag
thoroughly.

VACUUM-PACKING BOX
Rinse the vacuum-packing box and parts thereof with water and detergent (or wash them
in a dish-washer). Allow all the parts to dry out properly before next use or storage.

V. ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing,
components and accessories as well as their recycling on all parts. The symbols specified
on the product or in the accompanying documentation mean that the used electric or
electronic products must not be disposed of together with municipal waste. For proper
disposal of the product, hand it over at special collection places where it will be taken
over free of charge. Suitable disposal of the product can help to maintain valuable natural
resources and to prevent possible negative impacts on the environment and human
health, which could be the possible consequences of improper waste disposal. Ask for
more details at the local authorities or in the nearest collection site. Fines can be imposed
for improper disposal of this type of waste in agreement with the national regulations.
If the appliance is to be put out of operation for good, after disconnecting it from power
supply we recommend cutting off the power cord and thus it will not be possible to use the
appliance again.
Expert service must do the large maintenance or to intervene into inside parts of the
appliance! Non-observance of the instructions of the manufacturer cancels the right
for guarantee repair!

VI. TECHNICAL DATA

Voltage (V) shown on the type label of the appliance
Absorbed power (W) shown on the type label of the appliance
Weight (kg) approximately 2.8
Protection class of the appliance II.
Size, (mm): 410 x 180 x 145
Input in standby mode is < 1 W
The manufacturer reserves the right to change the technical specifications and
accessories for the respective models.

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS;
TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC
BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS
BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS
NOT A TOY.

WARNING: HOT SURFACE

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>