Fanvil i10SD SIP Mini Intercom Installation Guide
- June 4, 2024
- Fanvil
Table of Contents
i10SD SIP Mini Intercom
Installation Guide
www.fanvil.com
Package Contents
| Mini Intercom
---|---
| Quick Installation Guide
| Screw and tool
| Connector
| Mounting Template
Physical specification
| Device size | 88 x 88 x 32 mm |
|---|---|
| i10SV | No camera, 1 button |
| i10SD | With a camera, 1 button |
| i10S | No camera, 2 button |
Panel
Interface description
Open the rear case of the device, there is a row of terminal blocks for
connecting the power supply, and indoor switch. The connection is as
follows:
| Serial number | Description |
|---|---|
| 1 | Ethernet interface: standard RJ45 interface, 10/100M adaptive, it is |
recommended to use five or five types of network cable
2| Power interface: 12V/1A input
3| A set of short-circuit output interfaces
4| A set of short-circuit input interfaces
Installation Diagram
a. Installation of rubber plug:
a) Wall mount: Attach the installation dimension drawing to the position to be
installed, use the electric drill to punch the hole in the 2 screw holes
marked, and use the hammer to drive the rubber plug into the drilled hole.
b) Built-in: Attach the installation dimension drawing to the position to be
installed, open a groove of the same size according to the size, use the
electric drill to punch the hole in the 2 screw holes marked, and use the
hammer to drive the rubber plug into the drilled hole.
Fanvil Technology Co., Ltd
Website: www.fanvil.com
Email: sales@fanvil.com
support@fanvil.com
Tel: +86-755-2640-2199 Fax: +86-755-2640-2618
Add 10/F Block A, Dualshine Global Science Innovation Center,
Hong long North 2nd Road, Bao’an District, Shenzhen, China
b) Remove the cover;
c) Use a screwdriver to remove the 4 screws on the main body to separate the
main body from the rear case;
d) Pass all the wires through the hole in the lower right corner of the bottom
case. All lines must be reserved for a length of 15~20CM;
e) Fix the housing
a) Wall Mount: Align the bottom case with the position of the screw hole that
was previously punched on the wall, and screw in the two screws with a
screwdriver to fix the bottom case to the wall;
b) Built-in: Place the bottom case into the previously opened groove and screw
in the two screws with a screwdriver to secure the bottom case to the wall;
f) Connect the power, network, and control cables, and test whether there is
electricity by doing the following:
a) Long press the DSS key for 3 seconds(after power-on for 30 seconds), and
when the speaker beeps rapidly, press the DSS key again quickly, the beeps
stop, and the intercom will report the IP address by itself.
b) If the work is normal, continue with the next steps.
g) Lock the 4 screws removed in step 3;
h) Cover the cover removed in step 2;
Searching device
Methods 1:
Download address:
http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe
Open the door phone Network Scanner. Press the Refresh button to search the
device and find the IP address.
Method 2:
Long press the DSS key for 3 seconds(after power-on for 30 seconds), and when
the speaker beeps rapidly, press the DSS key again quickly, the beeps stop,
and the intercom will report the IP address by itself.
Method 3:
In addition, the device provides the device surface DSS key operation to
switch IP address acquisition mode:
In the standby mode, long-press the DSS key for 3 seconds, and the beep will
last for 5 seconds. Within 5 seconds, press the DSS key three times quickly to
switch to the network mode.
a. If it is in the mode of DHCP and doesn’t receive the IP address, switch it
to the mode of static IP (192.168.1.128), and broadcast the IP address after
the successful switch.
b. If it is in the mode of static IP address (192.168.1.128), switch it to the
DHCP mode, and broadcast the IP address after the successful switch.
c. If it is in the mode of DHCP and obtains the IP address, the mode will not
be switched and directly broadcast the IP.
Default Setting
Default DHCP Client| Enabled by default| Static IP address| 192.168.1.128
Default DHCP Client| Hold the DSS key for 3 seconds, then press the DSS key
again.| Default Web port| 80
Fast settings
Step 1: Log in to the device page
Use the web browser input IP (for example http://192.168.1.128) access.
The default user and password are admin.
Step 2: Set SIP account
Set the SIP server address, port, user name, password, and SIP user with
assigned SIP account parameters. Select “Activate”, and then click [Apply] to
save this setting.
Step 3: Set the volume (if not connected can skip)
Intercom settings => Media Settings => Media Settings
Set the device volume size, as shown below, and click [Apply].
Speakerphone volume setting: set the speaker volume for normal calls.
Handsfree Mic Gain: set the microphone volume of the call.
Step 4: Set function key (if not connected can skip)
Set the function key as shown below for a quick start, and click [Apply] to
save this setting.
Type: Memory key
Number 1 (Value): the function key will dial to this number 1
Number 2 (Value 2): if number 1 is unavailable, it will be forwarded to number
2.
Subtype: speed dial
Line: working line
Step 5: Set the security function
1 set of short-circuit input and output settings, tamper alarm server
settings.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>