Industrial IP67-1P-2P Port Gigabit PoE Plus Installation Guide
- June 4, 2024
- INDUSTRIAL
Table of Contents
Industrial IP67-1P-2P Port Gigabit PoE Plus
Product Information
Specifications
- Product Name: Industrial IP67 1-Port Gigabit PoE++ to 2-Port Gigabit PoE++ Repeater
- Power Supply Technology: Network cable
- Signal Extension: 1000Mbps Ethernet signal to 100m
- PoE Output: 50~57V standard PoE
- Grade: Industrial grade
- Design: IP67 waterproof
- Working Temperature: -20~75 degrees Celsius
Product Usage Instructions
Application
The repeater is suitable for security monitoring and network engineering
applications.
Interfaces and Indicator
The system indicator supports four states:
- Off: No power input on the PoE input port.
- On (Red): Normal power input on the PoE input port, but no output power on the PoE output port.
- On (Green): Normal power input on the PoE input port, and normal output power on the PoE output port. No data transfers.
- Flashing (Green): Normal power input on the PoE input port, normal output power on the PoE output port, and data transfer is occurring.
Installations
- Step 1: Pass the RJ-45 cable through the waterproof joint. Use non-sheathed cable for better performance.
- Step 2: Tighten the waterproof connector clockwise.
- Step 3: Repeat steps 1 and 2 for complete wiring.
Wall-mounted Installations
The repeater can be wall-mounted in two ways:
- Fix to the wall with 4 screws.
- Hang to the wall with 2 screws.
Caution
- Use Cat5e or better cables for better transmission performance.
- Connect the PoE input and output ports correctly to ensure normal device operation.
- Tighten waterproof joints for improved waterproof performance.
- Avoid damaging flush-mounted installations like cables or pipes when drilling holes in walls.
- Power on the system only after confirming correct wiring to prevent equipment damage.
- Read the user manual carefully before operating or maintaining the repeater to avoid misoperation.
FAQ
-
Q: What type of cables should be used with the repeater?
A: It is recommended to use Cat5e or better cables for optimal performance. -
Q: How can I ensure proper device operation?
A: Make sure to connect the PoE input and output ports correctly according to the user manual. -
Q: What should I do before powering on the system?
A: Confirm that the wiring is correct to avoid any damage to the equipment.
Packing List
| Items | Quantity |
|---|---|
| Repeater | 1 pc |
| Mounting Accessory | 1 set |
| Quick Installation Guide | 1 pc |
Product Overview
The product is an Industrial IP67 1-Port Gigabit PoE++ to 2-Port Gigabit PoE++
Repeater, using network cable power supply technology, and can extend 1000Mbps
Ethernet signal to 100m and provide 50~57V standard PoE for powered devices.
The repeater is an industrial grade, with an IP67 waterproof design and wide
working temperature of -20~75℃. It can withstand harsh environmental tests and
is suitable for security monitoring and network engineering.
Application
Appearance and Dimensions
Dimensions (mm)
Interfaces and Indicator
Waterproof Joint
Indicator
The system indicator supports the following 4 states:
| State | Descriptions |
|---|---|
| Off | No power input on the PoE input port. |
| On (Red) | Normal power input on the PoE input port, but no output power on the |
PoE output port.
On (Green)| Normal power input on the PoE input port, and normal output power
on the PoE output port. No data transfers.
Flashing (Green)| Normal power input on the PoE input port, and normal output
power on the PoE output port. And It is transferring data normally.
Installations
Fixing the Cables
Before installation, power off the equipment. Installation when device is
powered on is prohibited. Please use Cat5e or better cables to connect the
repeater and the device. Connect the PoE injector or switch to the PoE input
port of the repeater. Connect the PoE-powered device to the PoE output port of
the repeater. Do not reverse it, otherwise the repeater will not work
normally. The waterproof joint allows RJ-45 cables pass through so that the
connector of the repeater can be directly connected to the RJ-45 cable, please
follow the steps below.
- Step 1: Pass the RJ-45 cable through the waterproof joint. The use of non-sheathed cable is recommended.
- Step 2: Tighten the waterproof connector clockwise.
- Step 3: Repeat steps 1 and 2 to complete the wiring.
Wall-mounted Installations
This repeater can be mounted to the wall in two ways:
- Fix to the wall with 4 screws.
- Hang to the wall with 2 screws.
Please follow the steps below.
Fix to the wall with 4 screws
Drill 4 holes on the wall where the device is installed. Insert an
expansion anchor into each hole drilled in the wall, and beat the top of it
with a rubber hammer until all the anchor is inserted into the wall.
Install the device to the wall with 4 screws as the figures below.
Fix to the wall with 4 screws:
Hang to the wall with 2 screws
Drill 2 holes on the wall where the device is installed. The diameters are as
the figures below. Insert an expansion anchor into each hole drilled in the
wall, and beat the top of it with a rubber hammer until all the anchor is
inserted into the wall. Install the device to the wall with 2 screws as the
figures below.
Hang to the wall with 2 screw:
The installation steps are finished.
Caution
- For better transmission performance, it is recommended to use Cat5e or better cables to connect the repeater and the equipment.
- Please connect the PoE input and output ports correctly, otherwise the device will not work normally.
- For better waterproof performance, please make sure the waterproof joints are tightened.
- When drilling holes in walls make sure not to damage flush-mounted installations like cables or pipes.
- Power on the system only after confirming that the wiring is correct, to avoid damage to the equipment.
- Read the user manual carefully before operating or maintaining the repeater to avoid misoperation.
Specifications
| Items | IEEE802.3bt PoE Repeater with 2 output ports (90W) |
|---|
Ethernet Ports
PoE Input Port| 110/100/1000Base-TX RJ-45
PoE Output Port| 210/100/1000Base-TX RJ-45
PoE
PoE Standard| IEEE 802.3af/at/bt
PoE Power Supply Type| End-span, Mid-span
PoE Pin Assignment| 1/2(-), 3/6(+), 4/5 (+), 7/8 (-)
Input Voltage| 50~57V DC, max 90W
PoE Output Power| 65W(max)
Single Port PoE Output Power| 60W(max)
Switch Property
Standards| IEEE 802.3,IEEE 802.3u, IEEE 802.3ab
Forwarding Modes| Store and Forward
Transmission Distance| Extend 100m by 1pcs, max. 400m when 3pcs in cascade
MAC Table| 2k
Switching Capacity| 6Gbps
Packet Forwarding Rate| 4.46Mpps
Flow Control| IEEE 802.3x pause frame for full duplex, Back pressure for half
duplex
Jumbo Frame| 10kB
Environment
Surge Immunity| 6kV, Standard: IEC61000-4-5
ESD Protection| 6kV Contact Discharge, 8kV Air Discharge, Standard:
IEC61000-4-2
Enclosure| IP67-rated and IK10 aluminum case
Operating Temperature| -20℃~75℃
Storage Temperature| -40℃~85℃
Operating Humidity| 0~95% (No condensation)
Physical Parameters
Dimensions (WDH)| 195mm75mm42mm
Net Weight| 519g±10g
Material| Metal Shell
Installation| Wall-mounted
Certifications
Certifications| CE, FCC
Version: V1.0, updated 2023-10-08.
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to ensure
accuracy of the contents, but all statements, information, and recommendations
in this document do not constitute a warranty of any kind, express or implied.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>