AGT INDUSTRIAL AGT-SVH30 Single Drum Road Roller Owner’s Manual

October 30, 2023
AGT INDUSTRIAL

AGT INDUSTRIAL AGT-SVH30 Single Drum Road Roller Owner’s Manual

[](https://manuals.plus/wp-content/uploads/2023/06/AGT-INDUSTRIAL-AGT-

SVH30-Single-Drum-Road-Roller-Owners-Manual_2.png)PRODUCTMANUAL

  • This equipment can not be installed, operated or repaired without reading instructions.
  • Electricity must be hooked up by certified electrician.
  • Do not use this equipment beyond its rated capacity. Missing parts or questions on assembly? Please contact us.

Brief

Thank you for using our products. We will continue to support your work. Thank you!

One. Products Brief

This walk-behind roller mining CF178F diesel-powered, high performance, quality assurance, use
centrifugal clutch CVT. Hydraulic two-way travel, use chain walking, torque, more stable. Exciting force is
directly controlled by the throttle, easy operation, mobile and flexible. Machine features: small size, compact structure, foldable operating handle to operator with a comfortableoperating environment, it can be folded for easy transport and collection. With supporting large rollers use. Widely used in large auxiliary roller (subgrade, base surface, asphalt surface) sidewalk, covers periphery, curbs, small-scale pavement engineering, road pavement landfill compactor after patching potholes, highway repair, backfill compaction, a small parking lot, stadium compaction. Roads, municipal roads department, ideal for thesquare.\

Two、Technical Parameters:

Type AGT-SVH30 AGT-SVH30C
Run  
Speed 0-3.8KM/H
Climbing capacity in theory 30%
Compaction  
Static load forward/back 45N/cm
Nominal amplitude 0.6mm
Vibration frequency 70Hz
Exciting force 15KN
Water tank volume 22L
Working  
Drive Two-way hydraulic & chain drive
Vibration Automatic centrifugal clutch
Engine  
Model HONDA/BRIGGS&STRATTON CHANGFA CF170


Type

| Gasoline & Single Cylinder & Vertical & Four Stroke & Overhead valves| ****

Diesel & Single Cylinder & Vertical & Four Stroke & Air & Diesel injection

Power| 5.5 hp/3600/rpm| 4.2 hp/3600/rpm
Fuel Capacity| 3.6L| 1.9L


Lubricant

| ****

0.6L

| ****

0.75L

Hydraulic Tank Capacity| 15L| 10L
Dimension|  |
Wheel Size| 426600mm
Full Width| 780mm
Machine Length| 1600mm
Machine Height| 1060mm
Packing size| 1050
850*1200mm
Weight|  |
Working weight| 330kg| 330kg

Three 、Precautions

1、 before each launch start, do check before operation, to avoid personal injury and equipment damage.
2、 TO prevent fires, ensure good ventilation, Operator put Engine from buildings and other equipment at least 1 meter distance. Do not put combustibles at side of engine.
3、 children and pets must stay away from operating area ,to prevent burns by gasoline engine parts or hurt by operating equipment .
4、 Learn how to shut down operation of device and all control components quickley, never allow untrained personnel to operate equipment.
5、 Do not put combustible materials (such as gasoline, lighters and other equipment) are placed next to moving equipment. To add fuel in a well ventilated place, stop running before refueling engine, gasoline is highly flammable and would explode under certain conditions.
6、 Do not overfill fuel tank, fuel filler neck should not have fuel. If fuel overflows, etc. shall be removed and waiting for evaporate before starting engine.
7、 where engine or fuel to increase fuel storage. No smoking or open flames.
8、 Engine exhaust including carbon monoxide, avoid inhalation, and never operate machine in a closed, unventilated poorly ventilated areas.
9、 when engine is running, muffler will be very hot and heat will be continued a period of time after stopping, do not touch it,                    to avoid burns or fire, allow       to cool down engine, then move it or store it into room

Four. Device Control

1、Fuel value

Fuel valve is for controlling passage between fuel tank and carburetor when engine is running, fuel valve must be pulled to ON position. When engine is not used, pull fuel valve to OFF position. Prevent oil outflow in carburetor, reducing possibility of leakage of gasoline.

2、Engine ON/OFF

Engine switch controls ignition system, put engine switch to open position, start engine, put engine switch to OFF position, shut down engine.

3、Choke lever
Choke rod control carburetor lever. When choke lever is located OFF position, improve concentration of gasoline to cold start engine. After engine is started, choke lever located at open position, to provide suitable fuel for its operation, but also for starting engine heat engine provides right fuel.

4、Throttle lever
Throttle lever controls engine speed, put throttle lever in desired engine speed position.

Five.Run

(One) Checking before running

1、Check engine, hydraulic tank and look and bottom of tubing ,to see if oil spill.
2、Wipe off excess dirt and other obstacles, especially around muffler and recoil starter
3、Check appearance , if all nuts, bolts and screws are strong, whether drive belt and chain is too loose ?.
4、Check engine and hydraulic oil tank level, low fuel runs may result engine damage, unsteady gait, periodic replacement of engine oil and hydraulic oil, to avoid damage due to an accident, check the oil level before starting.
5、Check air filter, dirty air filter will reduce amount of air into carburetor, reducing engine power.
6、Check   V-belt, if chain is normal

Two )Roller start operation

1、Put Engine fuel valve plate to open position, put hydraulic reversing handle into forward or reverse position. During Engine is heating, pull choke lever to on position.
2、Engine switch is turned to ON position
3、Gently pull recoil handle until resistance is felt, then quickly pulled, slowly back into handle.
4、After starting engine, if choke lever in OFF position, slowly move it to open position, let engine warm, Starting work after idling five minutes .
5、In warm-up operation launched, push front roller valve forward, move rear roller valve backward walking.
6、Pull back throttle lever, roller compaction operations.

Three)Shut down road roller

1、If Emergency, simply pull handle to stop position.
2、Under normal circumstances, Pull handle to stop position, push throttle lever forward, engine idle speed, then engine switch to OFF position.

6 . Engine Maintance

Note:

  • maintenance issues

  • Project with emissions associated

  • Replace paper part only

    • In dusty places, plus ground
    • Unless user has proper tools and maintenance
    • Engine for commercial purposes, good record running time, to determine maintenance

ceven. Common Problem

Lack of engine power| ****

Problem

| ****

Treatment

---|---|---



1、  Check control

position

| Fuel valve is not open| Pull valve to open
Open choke| Close choke
Engine switch is not open| ****

Engine switch to open



2、  Check fuel

| No gasoline| Add gasoline
Add deteriorated gasoline or gasoline has gone| ****

Drain fuel tank, carburetor fuel, add new gasoline



3、  Remove spark plug inspection

| ****

spark plug is damaged, dirty and incorrect gap

| ****

Clean, adjust gap or replace spark plugs


spark plug is wet fuel

| Dried and Refit spark plug, pull valve lever tofastest position
1、 check air filter| ****

Filter blocked

| Clean or replace the

filter

---|---|---
2、 Check fuel| Add deteriorated

gasoline or gasoline has

| Drain fuel tank,

carburetor fuel, add

Eight. Hydraulic System

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

AGT INDUSTRIAL User Manuals

Related Manuals