LCN 4040T Smooth Heavy Duty Track Closer User Manual

: June 2, 2024
: Allegion

LCN 4040T SERIES User Manual

LCN 4040T

The 4040T SMOOTHEE® is LCN’s most flexible heavy duty track closer designed specifically for interior doors in institutional and other rugged high traffic applications.

FEATURES

Cast Iron
Forged Steel Arm
Double Heat Treated Steel Pinion
All Weather Fluid
Non-Handed
Fast & Accurate Installation
UL & cUL Listed

LCN 4040T

Standard 4040T series closer is shipped with standard arm, standard track, track roller, standard plastic cover, and self reaming and tapping screws. See 4040T Series pages 55 & 56 for options
Non-sized cylinders for interior doors to 4’0”.
Closer mounts pull side on door, pull side top jamb or push side on door.
Closers to meet ADA requirements. See 4040T Series page 57.
Standard or optional custom powder coat finish.
Optional plated finish on metal cover, arm and fasteners.
Optional SRI primer for installations in corrosive conditions is available with powder coat only.
Consult factory for double egress applications.
Optional designer series metal cover
The 4040T Series is UL and cUL listed with a standard track for self-closing doors.
Tested and certified under ANSI Standard A156.4, grade one.

ANSI Standard A156.4

MOUNTING DETAILS

HINGE (PULL) SIDE MOUNTING

MAXIMUM OPENING

Templating allows 120° with standard arm, limited to 110° when optional bumper is installed.

Hold-open points at 85°, 90°, 95°, 100°, 105° , or 110°, depending on the clip location in track.

Optional, Non-handed Designer Series Metal Cover

Optional, Non-handed

Options

Standard track with bumper, hold-open track, hold-open track with bumper.
Metal or lead lined cover.
Designer Series metal cover
ST required for double egress applications. Consult factory

Special Templates
Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance.

Mounting Details

Butt Hinges should not exceed 5” (127 mm) in width.
Auxiliary Stop is recommended at hold-open point or where a door cannot swing 120°. Optional track bumper assembly assists backcheck in cushioning the opening swing of the door. It is not intended to replace an auxiliary stop.
Reveal should not exceed 1/8” (3 mm) for standard arm.
Top Rail less than 3 3/4” (95 mm) requires PLATE, 4040T-18. Plate requires 1 13/16” (44 mm) minimum. With Designer Series metal cover, use PLATE, 4040T-18DS1.
Head Frame requires 1 1/4” (32 mm) minimum.
Clearance of 2 1/4” (57 mm) behind door required for 90° installation.

Mounting Details 2

Butt Hinges should not exceed 5” (127 mm) in width.
Auxiliary Stop is recommended at hold-open point or where a door cannot swing 180°. Optional track bumper assembly assists backcheck in cushioning the opening swing of the door. It is not intended to replace an auxiliary stop.
Reveal should not exceed 1/8” (3 mm).
Head Frame less than 3 7/8” (98 mm), requires PLATE, 4040T-18TJ. Plate requires 1 3/4” (44 mm) minimum. With Designer Series metal cover, use PLATE, 4040T-18TJDS1.
Clearance of 1 1/4” (32 mm) behind door required for 180° installation.

TOP JAMB (PULL SIDE) MOUNTING

MAXIMUM OPENING

Templating allows 180° with standard track arm, limited to 110° with optional bumper installed.

Consult factory if door will be held open at 180°

Hold-open points at 85°, 90°, 95°, 100°, 105° or 110° with hold-open tracks.

Optional, Non-handed Designer Series Metal Cover

Optional, Non-handed Designer Series Metal Cover

Options

Standard track with bumper, hold-open track, hold-open track with bumper.
Metal or lead lined cover.
Designer Series metal cover

Special Templates
Customized installation templates or products may be available to solve unusual applications.
Contact LCN for assistance.

STOP FACE (PUSH SIDE) MOUNTING

MAXIMUM OPENING

Templating allows 120° with standard track arm, limited to 110° with optional bumper tracks.

Hold-open points at 85°, 90°, 95°, 100°, 105° or 110° with hold-open tracks.

Optional, Non-handed Designer Series Metal Cover

Optional, Non-handed Designer Series Metal Cover

Options

Standard track with bumper, hold-open track, hold-open track with bumper.
Metal or lead lined cover.
Designer Series metal cover

Special Templates
Customized installation templates or products may be available to solve unusual applications.
Contact LCN for assistance.

Mounting details 3

Butt Hinges should not exceed 5” (127 mm) in width.
Auxiliary Stop is recommended at hold-open point or where a door cannot swing 120°. Optional track bumper assembly assists backcheck in cushioning the opening swing of the door. It is not intended to replace an auxiliary stop.
Clearance projects 2 1/4” (57 mm) from face of door.
Top Rail less than 5 1/4” (133 mm) measured from the stop, requires PLATE, 4040T-18. Plate requires 3 1/2” (89 mm) minimum. With Designer Series metal cover, use PLATE, 4040T-18DS1.
Stop Width minimum 1 1/4” (32 mm).

ACCESSORIES

CYLINDERS

CYLINDER, 4041T-3071

COVERS

COVER, 4040T-72
Standard, non-handed plastic cover

LEAD LINED COVER, 4040T-72LL
Optional, non-handed plastic cover.

METAL COVER, 4040T-72MC
Optional, handed cover. Required for plated finishes and custom powder coat finishes.

DESIGNER SERIES METAL COVER, 4040T-72DS1
Optional, non-handed designer series metal cover

ARMS

STANDARD ARM, 4040T-3077T
Non-handed arm.
Arm does not include track roller.

DOUBLE EGRESS ARM, 4040T-3077DE
Optional, handed arm for double egress doors and frames.
Arm does not include track roller.
Maximum reveal is 2 11/16” (68mm).

TRACKS

STANDARD TRACK, 4040T-3038
Standard, non hold-open, non-handed track.
Will accept hold-open clip and/or bumper assembly.

STANDARD TRACK with BUMPER, 4040T-3038B
Optional non hold-open, non-handed track with bumper assembly installed.
Will accept hold-open clip.

HOLD-OPEN TRACK, 4040T-3038H
Optional, non-handed track with hold-open clip installed.
Will accept bumper assembly.

HOLD-OPEN TRACK with BUMPER, 4040T-3038HB
Optional, non-handed track with hold-open clip and bumper assembly installed.

INSTALLATION ACCESSORIES

PLATE, 4040T-18TJ/ 4040T-18TJDS1
Required for pull side top jamb installations where head frame is less than 3 7/8” (98 mm). Plate requires minimum 1 3/4” (44 mm) head frame. With Designer Series metal cover, use PLATE, 4040T-18TJDS1.

PLATE, 4040T-18/4040T-18DS1
Required for pull side (door mount) installations where top rail is less than 3 3/4” (95 mm).
Plate requires minimum 1 3/4” (44 mm) top rail.
Required for push side (door mount) installations where top rail is less than 5 1/4” (133 mm) measured from the stop.
Plate requires minimum 3 1/2” (89 mm) top rail. With Designer Series metal cover, use PLATE, 4040T-18DS1.

TRACK BUMPER, 4040T-169
Mounts in track to assist backcheck, does not replace auxiliary stop. Limits maximum opening. Consists of bumper, bumper post, and mounting screw.

HOLD-OPEN CLIP, 4040T-3054
Mounts in track to provide hold-open function.
Hold-open point controlled by clip location.
Consists of clip and mounting screws.

TRACK ROLLER, 4040T-3034
Quiet, low friction roller assembly.
Shoulder dimension “X” = 1/8″ (3mm).

ORDERING INFORMATION

TABLE OF SIZES

Non-Sized 4041T cylinder is adjustable from sizes 1 thru 4 and is shipped set to size 3.

Indicates recommended range of door width for closer size.

Door Width

REDUCED OPENING FORCE 4040T CLOSERS

CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door.

Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without effecting closing power.

Door Width 2

* Maximum opening force

HOW-TO-ORDER 4040T SERIES CLOSERS

1. SPECIFY FINISH
Standard Powder Coat __
Aluminum, Dark Bronze , Tan, Statuary, Light Bronze, Black, Brass

Closer will be shipped with:
– STANDARD COVER,
– STANDARD ARM,
– TRACK ROLLER,
– STANDARD TRACK,
– SELF-REAMING and TAPPING SCREWS,
unless options listed below are selected