FL15-650WH1 Neomounts Tablet Floor Stand Instruction Manual
- June 1, 2024
- Neomounts
Table of Contents
FL15-650WH1 Neomounts Tablet Floor Stand
Product Information
Specifications:
- Measuring unit: mm
- Model: FL15-650WH1
- Manufacturer: NEOMOUNTS
Product Usage Instructions
Step 1: Attach the Adhesive Pads
Attach the adhesive pads (O) to the bottom of the base as shown in the manual.
Step 2: Route Cable and Attach Pole
Route the cable and attach the pole to the base according to the instructions provided.
Step 3: Install Mount on Floor
Install the mount on a concrete or brick floor following the given guidelines.
Step 4: Attach Holder and Place Tablet
Attach the holder to the pole and unlock it. Then, remove the cover and place the tablet in the holder.
Step 5: Attach Panel and Adjust Clamps
Attach the panel to the holder with screws (L) and adjust the clamps for proper alignment of the tablet before tightening the screws.
Step 6: Final Setup
Follow any additional instructions provided with the product for final setup and adjustments.
Frequently Asked Questions
Q: How do I choose the correct panel for my tablet?
A: Choose the corresponding panel based on your tablet model. Panel 1 is for 9.7 iPad 5/6, iPad Air 1/2 & iPad Pro (Gen 1), Panel 2 is for 10.2 iPad 7/8/9 & 10.5 iPad Air 3, iPad Pro (Gen 2), Panel 3 is for 11 iPad Pro (Gen 3/4/5) & 10.9 iPad 10, iPad Air 4, Panel 4 is for 10.4 Samsung Galaxy Tab A7, Panel 5 is for 10.1 Samsung Galaxy Tab A, and Panel 6 is for 10.4 Samsung Galaxy Tab S6 Lite.
Dimension
Tools
PARTS
Installation Instruction
STEP 1
Attach the adhesive pads to the bottom of the base
STEP 2
Route the cable and attach the pole to the base
STEP 3
Install the mount on a wooden floor
STEP 3 B
Install the mount on a concrete brick floor
STEP 4
Attach the holder to the pole and unlock the holder
STEP 5
Remove the cover and place the tablet in the holder 
Choose the corresponding panel according to the tablet:
- Panel 1: For 9.7” iPad 5/6, iPad Air 1/2 & iPad Pro (Gen 1)
- Panel 2: For 10.2” iPad 7/8/9 & 10.5” iPad Air 3, iPad Pro (Gen 2)
- Panel 3: For 11” iPad Pro (Gen 3/4/5) & 10.9” iPad 10, iPad Air 4
- Panel 4: For 10.4” Samsung Galaxy Tab A7
- Panel 5: For 10.1” Samsung Galaxy Tab A
- Panel 6: For 10.4” Samsung Galaxy Tab S6 Lite
STEP 6
Adjust the torque
STEP 7
Adjust the mount to the desired position
CAUTION
- To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in a secure place for future reference.
- The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
- The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon.
- It is recommended that the mount be installed by qualified personnel only.
- At least two persons are needed to install or remove the product to avoid hazard of falling objects.
- Please carefully inspect the area where the mount is to be installed:
- Avoid places that are subject to high temperatures, humidity or contact with water.
- Do not install the product near air conditioning vents or areas with excess dust and fumes.
- Only install on vertical walls and avoid slanted surfaces.
- Do not install in places subject to any shock or vibration.
- Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
- Maintain sufficient space around the display to ensure adequate ventilation.
- To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
- The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
- Do not modify any accessories or use broken parts. Contact your dealer with any questions.
- Tighten all screws (do not exert excessive force to avoid breaking the screw or damaging its thread).
- Drill holes and bolts will be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
- Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
- Please consult the English language manual for any dispute on conditions.