LEVOLOR SHADES Skylight with Automation Instruction Manual

June 1, 2024
LEVOLOR

CELLULAR SHADES
Skylight with Automation

IMPORTANT: This application MUST be installed as an inside mount.

Installing the Brackets

LEVOLOR SHADES Skylight with Automation - Installing the
BracketsUsing the mounting bracket (included) as a template, measure to the edge of the bracket and mark the hole locations with a pencil for drilling. End brackets should be located approximately 3” from either end. Use a 3/32” drill bit to drill holes for the screws. Depending on the width of the shade, additional brackets may be necessary, evenly spaced between the two end brackets.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors and follow the instructions provided with the anchors. (Anchors not provided)

Installing the Top Rail

IMPORTANT: Prior to installing the shade, attach the power supply to the motor and pair the motor with the remote using the included remote instructions
LEVOLOR SHADES Skylight with Automation - Top RailStart with the top rail (the rail with the motor in it). Make sure that the receiver wire is out of the headrail before mounting. Position the receiver wire so that it is facing into the room and position the motor wire so that it comes out the back side of the shade, ensuring it is not pinched by the bracket.
Position the rail with the front lip (A) resting on the hooks of all the brackets.
Push the rail firmly up and toward the window until the groove on the rail snaps into place, (B) as shown. After the top rail has been installed, the power supply should be connected and Solar Panel (if ordered with rechargeable battery pack) should be attached.

Installing the Bottom Rail

IMPORTANT: Make sure remote is paired to shade before installing.
LEVOLOR SHADES Skylight with Automation - Bottom RailPosition the rail with the front lip (A) resting on the hooks of all the brackets.
Push the rail firmly down and toward the window until the groove on the rail snaps into place, (B) as shown.

Installing the Tracks

LEVOLOR SHADES Skylight with Automation - TracksPlace the track against the front of the top and bottom rails. Attach the track with the screws provided. Space the screws no more than 12” apart.
Follow the same procedure for the other track. Make sure that the 2 tracks are parallel to each other.

Leveling the Moving Rail

LEVOLOR SHADES Skylight with Automation - Moving RailIf the moving rail is uneven it can be leveled using the shade adjust on the bottom of the rail. Use a flat head screwdriver or a dime to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the bottom of the moving rail. One quarter turn of the screw will move the moving rail up or down approximately 1⁄ 4”
IMPORTANT: Over-turning the adjustment screw (more than 1” of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily – Do Not Force

Troubleshooting
THE MOTOR DOES NOT WORK.

  • Check that the power source and motor are connected properly.
  • Check that the power supply is connected properly and charged. (if applicable)

THE MOTOR CONTINUES TO RUN IN ONE DIRECTION.

  • The limit setting was unsuccessful and needs to be reset.

THE MOTOR STOPS WORKING OR WORKS INTERMITTENTLY.

  • Recharge the batteries. If a solar panel is in use, ensure the connection to the battery is secure. Check to make sure any transformer or other external power supply is securely connected.

1a. Attach the Wand — Sheer Shadings, Banded & Roller Shades LEVOLOR SHADES
Skylight with Automation - AttachOn Banded Shades, Roller Shades and Sheer Shadings, with the wand control buttons facing you, attached the top of the wand on the metal hook support (1) on the motor control side, then connect the cable into the motor head (2). Note: On Sheer Shadings ordered with InMotion Wand on the right side, the cable may be wrapped around the hook. This is normal. You may unwrap, if you desire, as this does not affect functionality. You still need to connect the cable into the motor head.
1b. Attach the Wand — Cellular Shades![LEVOLOR SHADES Skylight with Automation

  • Attach 1](https://manuals.plus/wp-content/uploads/2024/05/LEVOLOR-SHADES- Skylight-with-Automation-Attach-1.jpg)On Cellular shades, the wand will be already connected to the shade (1).
    With the wand control buttons facing you, attached the top of the wand into the plastic hook support on the motor control side (2).
    1c. Attach the Wand — Natural Woven ShadesLEVOLOR SHADES Skylight with
Automation - Attach 0On Natural Woven Shades, with the wand control buttons facing you (1) approach the hook with the wand parallel to the headrail. (2) Gently twist the wand to attach it to the hook. Connect the cable into the motor.
    Important: Before starting the programing, install the shade following the installation instructions provided.
    Cellular shades are shipped with the motor in sleep mode to avoid activation during transit.
    For Cellular Shades, To wake up the motor prior to operating the shade:
    Press the STOP button 5 times (1) – the irst 4 times press quickly and the 5th time PRESS and HOLD the stop button until the motor jog (2). 2. Operate the WandLEVOLOR SHADES Skylight with Automation - Operate the
Wand Roller and Cellular Mode:

    • Press the DOWN or UP button to lower or raise the shade. Press the STOP to stop the shade at the desired position.

Sheer Shadings and Banded Shades Mode:

  • Tapping the UP or DOWN button for less than 2 seconds will move the shade in short steps.
  • Holding the UP or DOWN button down for more than 2 seconds before releasing will operate the shade at the standard speed.
  • Press the STOP button to stop the shade at the desired position.

3. Set a Favorite PositionLEVOLOR SHADES Skylight with Automation -
Favorite IMPORTANT: Once the favorite position is set, the shade will always stop at the designed favorite position when passing by it.
Click 2 x Up or Down button, the shade will go to set Top or Bottom Limit.
4. Remove a Favorite PositionLEVOLOR SHADES Skylight with Automation -
Favorite 1 5. Advanced Programming
IMPORTANT: Damage to shade may occur when operating the motor prior to setting limits. Attention should be given.
Switch between Roller and Sheer Shadings ModeLEVOLOR SHADES Skylight
with Automation - Favorite 2 Adjust the Top and/or Bottom LimitLEVOLOR SHADES Skylight with Automation - Bottom
Limit Factory Motor ResetLEVOLOR
SHADES Skylight with Automation - Bottom Limit 1 IMPORTANT: All limits will be erased. The motor direction will return to default and may need to be adjusted.
Reverse UP and DOWN Commands (Only if necessary)LEVOLOR SHADES Skylight
with Automation - Bottom Limit 2 Set Upper and Lower Limits ( Only after Factory Motor Reset)LEVOLOR SHADES Skylight with Automation - Bottom Limit
3 6. Charge the Battery When the shade begins to operate slower than normal or only beeps when you attempt to operate, it is time to charge the battery.
To Charge, connect a standard micro USB cable into the bottom of the wand (A) and into USB 5V/2A (max) power supply. A red LED on the wand indicates that the battery is charging. To fully charge the batteries, allow the batteries to charge for at least 1 hour after the LED on the wand turns green.
Note: A typical charge cycle can take between 4-6 hours.

Troubleshooting

Issues Possible Causes Solution
The shade is not responding Built in battery is depleted Recharge with

compatible USB 5V/2A (max) adapter and a
micro USB cable. Details under “6. Charge the Battery”
Wand is not fully connected to the motor| Check the connection between the wand and the motor
The shade moves the opposite direction on the control buttons| The motor direction is reversed| See details under “Reverse Up and Down Commands”
The shade stops by itself before it reaches
the top or bottom limit| A favorite position was set| See details under “4. Remove a Favorite Position”
The shade only moves in small steps after
pressing the button| The shade is operating on Sheer Shadings/Banded Shades mode| Switch to Roller/Cellular mode by following the steps under
“Switch between Roller and Sheer Shadings Mode”
The shade has no limit set| See details under “Set Upper and Lower Limits”

Child Safety

WARNING
Window Blind Cord Can STRANGLE Your Child.
To prevent strangulation, purchase cordless products or products with inaccessible cords.

1035121 • rev 01/244

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals