LEVOLOR 2 Custom Faux Wood Horizontal Blinds Installation Guide
- June 13, 2024
- LEVOLOR
Table of Contents
Real Wood & Faux Wood Blinds
INSTALLATION • OPERATION • CARE
Motorized Tilt Operation
CHILD SAFETY
Window Blind Cord Can STRANGLE Your Child
- Children can strangle in the loop above the cord bead.
- Children can climb furniture to reach cords.
- Move crib and furniture away.
- Shorten cords to prevent reach.
- Keep cords separate – Twisted or knotted cords can create a loop.
- Keep all cords out of children’s reach.
Always wrap the cords around the cleats in a figure eight, up high, out of
reach of children. WARNING: Keep all small parts, components and packaging
away from children as they pose a potential choking hazard which may result in
serious injury or death. Please reference all warning tags and labels in the
instructions and on the blind.
For installation support, questions, warranty information or replacement
parts, visit us at www.LEVOLOR.com.
WINDOW AND BLIND TERMINOLOGY
Thank you for purchasing LEVOLOR® Wood Blinds. With proper installation,
operation, and care, your new blinds will provide years of beauty and
performance. Please thoroughly review this instruction booklet before
beginning installation.
MOUNTING TYPES AND WINDOW TERMINOLOGY
If the installation brackets are mounted correctly, the rest of the
installation process follows easily. To prepare for this important first step,
review the mounting types and basic window terminology illustrated below.
| |
---|---|---
Window Components Terminology
• Collectively, the sill and jambs are called the “window casement” or
“frame”.| Inside Mount
• Blind fits within window opening.
• Great for windows with beautiful trim.| Inside Mount
•Blind fits within window opening.
• Great for windows with beautiful trim.
GETTING STARTED
COMPONENTS INCLUDED
TOOLS AND FASTENERS YOU MAY NEED
(not included)
The tools you will need for installing your blind will vary, depending on the
installation surface and mounting bracket type.
Tools typically used for installation include:
CAUTION: Use drywall anchors (not provided) when mounting into
drywall. Failure to properly anchor blind could cause blind to fall, possibly
resulting in injury.
INSTALLATION
INSTALLATION OVERVIEW
- Confirm the blind for proper width and length.
- If installing several sets of blinds, be sure to match them with the appropriate window.
- Check the installation surface to ensure that you have suitable fasteners and tools.
- Lay out and organize all parts and components.
Installation Brackets
Your order will include the correct number of installation brackets for your
blind width, as shown in the table below.
| Number of Brackets per Blind
Blind Width (inches)| End Brackets| Support Brackets
Up to 48| 2| 0
48 to 84| 2| 1
84 to 96| 2| 2
96 to 144| 2| 3
INSIDE MOUNT (IM)–BEFORE YOU BEGIN
PAIR SHADE BEFORE INSTALLING
REMOTE CONTROL
- Use the – and + buttons to select the channel.
- Use a paperclip to press and hold the programming button inside the headrail for about 2 seconds until the blind jogs once.
- In the next 10 seconds, press and hold the stop button on the remote until the blind jogs twice.
USING THE INMOTION APP
- If you purchased a hub, download the LEVOLOR InMotion™ app to get started.
- Blind can be directly paired to app, but it is recommended to pair to remote first.
INSIDE MOUNT (IM)
STEP 1: MARKING THE BRACKET LOCATIONS
-
Position the box brackets at each end of the headrail to confirm the dimension.
Depending on installation location, box brackets can be attached using the top, back, or the side holes. -
Position the center support bracket (if included) in the center, if using only one. If more than one center support bracket is included, space them evenly along the headrail.
-
Mark the location of the desired bracket mounting holes, two per bracket, making sure they are square and equally spaced.
STEP 2: INSTALLING THE BRACKETS
- Drill pilot holes using a 1⁄16″ drill bit using pencil marks as a guide. Depending on the installation location, box brackets can be attached using the top, back, or side holes.
- While holding the brackets in place, secure the brackets using two screws per bracket.
- Ensure all brackets are square with each other.
STEP 3: BATTERY INSTALLATION
- Attach battery clips to headrail as indicated by “Clip Here” stickers.
- Snap battery pack into clips with the wire on the left side.
- Connect battery to motor cable. Loop excess cords into clip on headrail.
STEP 4: INSTALLING THE BLIND
- Align the headrail and valance with the brackets and slide the headrail straight back into the brackets.
- If the headrail can slide from side to side in the box brackets, use a flat-head screwdriver to bend out the tabs on the ends of the headrail until it is snug.
- If center support bracket(s) are included, hook the front edge of the headrail into the channel on the bracket.
- Lower the front of each box bracket and press until the locking tab clicks into place.
CAUTION: Be sure the brackets are properly engaged before operating the
blind. Failure to do so may result in the shade falling and possible injury.
OUTSIDE MOUNT (OM)–BEFORE YOU BEGIN
PAIR SHADE BEFORE INSTALLING
REMOTE CONTROL
- Use the – and + buttons to select the channel.
- Use a paperclip to press and hold the programming button inside the headrail for about 2 seconds until the blind jogs once.
- In the next 10 seconds, press and hold the stop button on the remote until the blind jogs twice.
USING THE INMOTION APP
- If you purchased a hub, download the LEVOLOR InMotion™ app to get started.
- Blind can be directly paired to app, but it is recommended to pair to remote first.
OUTSIDE MOUNT (OM)
STEP 1: MARKING THE
BRACKET LOCATIONS
IMPORTANT: The brackets must be flush against a flat mounting surface. Do
NOT mount brackets on curved molding.
- Position the box brackets at each end of the headrail
- Position the center support bracket (if included) in the center if using only one. If more than one center support bracket is included, space them evenly along the headrail.
- Use a level to ensure all brackets are even and aligned. Mark the bracket mounting hole locations, two per bracket, making sure they are square and equally spaced.
STEP 2: INSTALLING THE BRACKETS
- Drill pilot holes using a 1⁄16″ drill bit using pencil marks as a guide.
- While holding the brackets in place, secure the brackets using two screws per bracket.
- Use a level to ensure all brackets are even and square with each other.
EXTENSION BRACKETS (optional)
- Optional extension brackets offers clearance for obstructions.
- Outside mounting extension brackets will provide 2–4″ clearance between the headrail and mounting surface. Assemble extension bracket as shown.
- Secure an extension bracket to each standard mounting bracket.
SPACER BLOCKS (optional)
- Outside mounting spacer blocks will provide an additional 3⁄8″ clearance as shown.
- If spacers are used, longer screws may be required to ensure a secure installation (not provided).
CAUTION: Do not use more than one spacer block. Using more than one
spacer block could cause blind to fall resulting in possible injury.
OUTSIDE MOUNT (OM)
STEP 3: BATTERY INSTALLATION
- Attach battery clips to headrail as indicated by “Clip Here” stickers.
- Snap battery pack into clips with the wire on the left side.
- Connect battery to motor cable. Loop excess cords into clip on headrail.
STEP 4: INSTALLING THE BLIND
- Align the headrail with the brackets and slide the headrail straight back into the brackets.
- If the headrail can slide from side to side in the box brackets, use a flat-head screwdriver to bend out the tabs on the ends of the headrail until it is snug.
- If center support bracket(s) are included, hook the front edge of the headrail into the channel on the bracket.
- Lower the front of each box bracket and press until the locking tab clicks into place.
CAUTION: Be sure the brackets are properly engaged before operating the
blind. Failure to do so may result in the shade falling and possible injury.
VALANCE INSTALLATION
- Locate the valance clip location indicators on the backside of the valance that read “Clip Here.”
- Insert the clips into the groove on the backside of the valance. Rotate so that the end marked “TOP” arrow is pointing up.
- For returns, insert L-shaped return clip into the groove on the backside of the valance return. Align and insert the other end of the L-shaped return clip into the groove on the backside of the valance.
- Align the clips with the slots on the bottom of the headrail and clip into place.
HOLD-DOWN BRACKETS INSTALLATION (optional)
- Ideal for doors, hold-down brackets prevent blind from swaying. Assemble as shown to each side of bottom rail.
OPERATION
REMOTE OPERATION
- Scan for remote guide.
https://qrco.de/bcod5C
BATTERY CHARGING
-
The rechargeable battery mounts between the headrail and valance.
-
For easier access to the charging port, a removable magnetic charging insert has been installed during production. Attach the magnetic charging adapter to the micro-USB charging cable and power adapter before connecting to battery to charge.
-
For standard charging, remove the magnetic charging insert from the battery. Use the micro-USB charging cable and power adapter to charge battery.
-
Indicator light battery status:
– Low (red flash)
– Charging (green flash)
– Charged (green solid) -
It is recommended to fully charge battery prior to first use.
LIFT OPERATION
NOTE: Lift control may be corded or cordless depending on what was
selected when ordering.
- Corded Lift: To raise the blind, pull cord in toward the center of the blind to release the lock; this allows you to raise and lower the blind. Once the blind is at the desired height, pull the cord away from the center to lock into position.
- Cordless Lift: To raise the blind, firmly press and hold the LEVOLOR button located on the bottom rail and lift the blind to the desired height. Once the desired position is reached, release grip on the button to lock blind in place.
UNINSTALL
REMOVING THE BLIND
- Fully raise the blind. Remove valance from headrail.
- Unplug battery from motor and remove from clips.
- Unlock and lift the front clips of each end box bracket and slide the headrail out of the brackets.
- If center support brackets are used, lift the front of the headrail up to clear the channel of the bracket and slide out forward.
- Uninstall remaining brackets if necessary.
CAUTION: Hold blind firmly when removing. Failure to do so may result in the blind falling and possible injury.
ADDITIONAL INFORMATION AND SUPPORT
CLEANING PROCEDURES
Keep your LEVOLOR® Wood and Faux Wood blinds looking their best by
periodically wiping them with a soft cloth, a duster, or the brush attachment
from a vacuum cleaner.
NOTICE: Avoid contact with window cleaning products. Improper cleaning
may void warranty.
DUSTING
Use a feather duster for regular cleaning.
FORCED AIR
Blow away dirt and debris using clean compressed air.
VACUUMING
Use a low suction vacuum with a brush-type cleaner attachment; stroke lightly
over the shade to clean.
SPOT-CLEANING/STAIN REMOVAL AT HOME
Faux Wood blinds only. You may use a soft, lightly dampened cloth to clean
your Faux Wood blinds.
WARRANTY
For complete warranty information visit LEVOLOR.com or call Customer Service
at 1-800-LEVOLOR or 1-800-538-6567.
CONTACTING US
To contact LEVOLOR Customer Service regarding any questions or concerns you
may have about your new shades, you may reach us at: 1-800-LEVOLOR (9:00 am –
6:00 pm EST).
www.LEVOLOR.com
ADDITIONAL PARTS AND SERVICES
Additional or replacement parts can be ordered, or shades can be repaired or
restrung through our repair center. Please contact LEVOLOR customer service
through www.LEVOLOR.com for a return authorization
number.
20-0048-082
©2022 LEVOLOR® , Inc.
5775 Glenridge Drive
Building A
Atlanta, GA 30328
1029599
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>