SPEAKA SP-HWE-800 HDMI Wireless Transmission Instruction Manual

SPEAKA SP-HWE-800 HDMI Wireless Transmission

FAQ

Frequently Asked Question

• Q: What should I do if the product malfunctions?
  • A: Ensure you are within the specified transmission range for proper operation.
• Q: How should I clean and maintain the product?
  • A: Turn off the monitor before cleaning and use a dry, lint-free cloth. The camera can be cleaned with a damp cloth or sponge.
• Q: How can I access the latest product information?
  • A: Download the latest product information from www.conrad.com/downloads or scan the QR code provided in the manual.

Introduction

Dear customer,

• Thank you for purchasing this product.
• If there are any technical questions, please contact: www.conrad.com/contact

Intended use

• This device allows wireless transmission of HDMI signals in 1080p resolution with a range of up to 150 metres. It features Switch and Splitter modes for displaying on different screens and has a pass-through function to connect a local screen to the HDMI transmitter. Since the latency is less than 300 ms, you can enjoy videos and games without noticeable lag. Furthermore, the integrated USB ports allow controlling a PC on the receiver side using a keyboard and mouse.
• The device also supports an infrared extender function that allows remote control of your device. You can enjoy music and audio without wires via an external audio port (3.5 mm headphone jack). The device is HDCP compliant and ideally suited for wireless transmission of HDMI signals between different spaces. It is also energy efficient and has low power consumption.
• The product is intended for indoor use only. Do not use it outdoors.
• Contact with moisture must be avoided under all circumstances.
• Using the product for purposes other than those described above may damage the product.
• Improper product use can cause a short circuit, fire, electric shock, other hazards.
• This product complies with statutory, national and European regulations. For safety and approval purposes, you must not rebuild and/or modify the product.
• Read the instructions carefully and store them in a safe place. Always provide these operating instructions when giving the product to a third party.
• All company and product names contained herein are trademarks of their respective owners. All rights reserved.
• HDMI is a registered trademark of HDMI Licensing L.L.C.

Restrictions

The product has restrictions for use in the following countries:

DE| AT| NL| SE| PL| SK| SI| LT| EE| LV
FI| FR| UK| BE| CZ| HU| IT| ES| PT| EL
DK| BG| CY| HR| IE| IS| LU| MT| RO|

Delivery Content

• Transmitter (TX)
• Receiver (RX)
• Infrared receiver
• Infrared transmitter
• USB-A cable
• 3.5 mm audio cable
• 4x antennas
• 2x 12V/1A power adapters
• Operating instructions

Latest product information And Symbols

Latest product information

• Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of symbols

The following symbols appear on the product/device or in the text:

• This symbol warns of hazards that can lead to injury.
• This symbol warns of a dangerous voltage which can lead to injuries due to electric shock.

Safety Instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General information

• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
• Should you have any questions or concerns after reading this document, please contact our technical support or a professional technician.
• Maintenance, modifications and repairs must be carried out only by a skilled technician or a specialist repair centre.

Handling

• Please handle the product carefully. Impact, shocks or a fall even from a low height can damage the product.

Operating environment

• Do not expose the product to any mechanical stress.
• Protect the product from extreme temperatures, strong jolts, flammable gases, vapours, and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.
• Never switch the device on immediately after taking it from a cold into a warm environment. This may cause condensation to form, which can destroy the product. Allow the product to reach room temperature before using it.
• Never operate the product in direct proximity of strong magnetic or electromagnetic fields or transmitter aerials or HF generators. Doing so can prevent the product from functioning properly.

Operation

• Consult an expert when in doubt about the operation, safety or connection of the device.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stress.

Power adapter

• Do not modify or repair power supply components, including power plugs, power cords and power adapters. Never use damaged components. Danger of death from electric shock!
• Connect the product to an easily accessible socket.
• Only use the supplied mains adapter as a power supply.
• Only connect the power adapter to a normal mains socket connected to the public supply. Before plugging in the power adapter, check whether the voltage stated on the power adapter complies with the voltage of your electricity supplier.
• Never connect or disconnect power adapters if your hands are wet.
• Never disconnect the mains plug from the socket by pulling on the cable. Always pull it out of the mains socket using the intended grips.
• For safety reasons, disconnect the power adapter from the mains socket during storms.
• Do not touch the power adapter if there are any signs of damage, as this may cause a fatal electric shock! Proceed as follows:
  • First, cut off the power supply to the corresponding mains socket (switch off the corresponding circuit breaker or remove the safety fuse, and then switch off the respective RCD safety switch so that all poles of the mains socket are disconnected).
  • Then carefully unplug the power adapter from the mains socket.
  • Use a new power adapter of the same design. Do not use the damaged power adapter again.
• Ensure the power cord is not pinched, kinked or damaged by sharp edges.
• Always lay cables so that nobody can trip over or become entangled in them. Failure to do so could result in injury.

Connections And Controls

Transmitter (TX)

Connection for the 12V/1A power adapter

2| HDMI OUT| HDMI output

Connection to a local display unit, “pass-through” function. (HDTV monitor/monitor, projector, etc.)

3| HDMI IN| HDMI input

Connection to your source device. (Laptop, PC, DVD player, set-top box, etc.)

4| AUX IN| Audio input
5| IR OUT| Infrared transmitter

Important:

Place the infrared transmitter so that it is pointed at the target unit (like when you want to control the unit with the infrared remote control).

6| USB PC| USB PC port

Connect the USB Type-A to Type-A cable to the USB port of your PC to control it.

7| RST| Reset button

Press the reset button for longer than 5 seconds to reset the device to factory defaults.

Important:

Use a straightened paper clip or similar object for this purpose. Never use a pointed object, such as a needle!

---|---|---
8| PWR| Power LED

It lights up when the device is powered on.

9| LINK| Link LED

The LED flashes when the receiver receives incoming data.

10| STA| Status LED

It lights up when the transmitter (TX) and receiver (RX) are linked and the HDMI signal is connected. This LED does not light up for AUX audio.

11| MODE| Mode button

Press the button to change the display mode: Graphic or Video mode.

(Long press to optimise signal transmission).

12| LED (1)| Display mode

OFF: Graphic mode -> Lowest latency (lag).

Ideal for transmitting static content without much lag, such as PC, images, etc.

ON: Video mode -> Lowest number of “dropped frames” (omitted images).

Ideal for transmitting motion pictures and content with a high frame rate.

13| LED (2)| Channel mode

OFF: Low frequency band. ON: High frequency band.

14| ID| Channel mode button

Press briefly to change the transmission channel.

Long press to switch between low and high frequency band.

The same channel must be set for the transmitter (TX) and receiver (RX).

15| LEDs

(1, 2, 4, 8)

| Channel display

0000 to 1111

16| SW| Switch mode

One receiver (RX) to multiple transmitters (TX). Up to 32 transmitters can be used.

17| SP| Splitter mode

One transmitter (TX) to multiple receivers (RX). Up to 4 receivers can be used.

Both TX and RX must be set to SP mode.

Receiver (RX)

Connection for the 12V/1A power adapter

2| HDMI OUT| HDMI output

Connection for an HDMI display unit, e.g. HDTV monitor/monitor, projector, etc.

3| AUX OUT| Audio output

Audio output to external speakers.

The HDMI output also serves to transmit audio signals, which can also be used.

4| IR IN| Infrared receiver

Infrared receiver connection.

5| USB K/M| USB port for keyboard and mouse

It allows controlling the PC using the keyboard and mouse.

6| RST| Reset button

Press the reset button for longer than 5 seconds to reset the device to factory defaults.

Important:

Use a straightened paper clip or similar object for this purpose. Never use a pointed object, such as a needle!

7| PWR| Power LED

It lights up when the device is powered on.

8| LINK| Link LED

The LED flashes when the receiver receives incoming data.

9| STA| Status LED

It lights up when the transmitter (TX) and receiver (RX) are linked and the HDMI signal is connected. This LED does not light up for AUX audio.

---|---|---
10| MODE| Mode button

Press the button to change the display mode: Graphic or Video mode.

(Long press to optimise signal transmission).

11| LED (1)| Display mode

OFF: Graphic mode -> Lowest latency (lag).

Ideal for transmitting static content without much lag, such as PC, images, etc.

ON: Video mode -> Lowest number of “dropped frames” (omitted images).

Ideal for transmitting motion pictures and content with a high frame rate.

12| LED (2)| Channel mode

OFF: Low frequency band. ON: High frequency band.

13| ID| Channel mode button

Press briefly to change the transmission channel.

Long press to switch between low and high frequency band.

The same channel must be set for the transmitter (TX) and receiver (RX).

14| LEDs

(1, 2, 4, 8)

| Channel display

0000 to 1111

15| SW| Switch mode

One receiver (RX) to multiple transmitters (TX). Up to 32 transmitters can be used.

16| SP| Splitter mode

One transmitter (TX) to multiple receivers (RX). Up to 4 receivers can be used.

Both TX and RX must be set to SP mode.

Installation location and range

If possible, you should perform a function test first. During the test, the transmitter should be only a few metres away from the receiver. Only when signal transmission works correctly should you place the devices at their final installation locations. This way, you can ensure that only the installation location causes the problems and not, for example, a low-quality HDMI cable.

• Place the transmitter and receiver so they stand freely. Do not place them behind other devices (e.g. behind a TV set). Otherwise, the radio signal will not be transmitted, and radio communication will not be possible (or the range will be too short).
• Never place the transmitter and receiver near other radio equipment (e.g. Internet router, repeater, etc.).
• For an optimum range, there should be as few walls/furniture etc., between the transmitter and receiver as possible, as they can significantly reduce the range.
• Assuming a direct line of sight and open field surroundings, the range of transmission of the radio signals between the transmitter and receiver is up to 150 metres. Obviously, this transmission range cannot be achieved indoors because of many factors affecting radio transmission. Try reorienting the antennas or choose a different installation location if necessary.
• Reduce the distance between the devices, use for example a longer (and high-quality) HDMI cable.
• Use suitable padding to protect the surfaces of valuable furniture against pressure marks, scratches and stains.

Getting Started

• First switch off all the devices that you wish to connect with the transmitter and receiver modules.

Antennae

• Screw the antennas to the rear of the receiver (RX) and transmitter (TX).
• When using the device for the first time, the antennas should point vertically upwards (the orientation of the antennas may vary, see “Installation location and range”).

Splitter mode: 1 transmitter, 1 receiver

• Set the switch on the receiver (RX) and transmitter (TX) to Splitter mode (SP).

Receiver (RX)

• Connect a monitor to HDMI OUT.
• Connect the power adapter (12V/1A).

Transmitter (TX)

• Connect a source device (HDMI IN), such as a laptop, PC, DVD player, set-top box, etc.
• Connect an optional monitor to HDMI OUT (loop-through function).
• Connect the power adapter (12V/1A).

The LINK LED on the transmitter (TX) and receiver (RX) flashes once the connection has been established. The STA LED on the transmitter (TX) and receiver (RX) is lit continuously during signal transmission.

When the monitor is connected to the receiver, and there is no signal, ensure the transmitter and receiver are set to Splitter mode (SP). Disconnect the receiver and transmitter from the power adapter. Reconnect the transmitter and then the receiver to the power adapter.

Switch mode

• In switch mode, transmission takes place via channel switching. In this way you can bind several transmitters or receivers with different channels, see illustration under 11.3.

1 transmitter to 1 receiver

• Set the switch on the receiver (RX) and transmitter (TX) to Switch mode (SW).

Receiver (RX)

• Connect a monitor to HDMI OUT.
• Connect the power adapter (12V/1A).

Transmitter (TX)

• Connect a source device (HDMI IN), such as a laptop, PC, DVD player, set-top box, etc.
• Connect an optional monitor to HDMI OUT (loop-through function).
• Connect the power adapter (12V/1A).

Multiple transmitters to 1 receiver

• Choose a different channel for each transmitter.
• You can toggle between the transmitters (sources) by switching the channels on the receiver (RX).

Up to 32 transmitters can be used.

Installing the remote control

There are two options for remote control of the units.

• Control via the infrared remote function (repeater function).
• Control via the keyboard and mouse (USB).

Infrared control (repeater function)

• Connect the infrared receiver to the receiver (IR IN) and the infrared transmitter to the transmitter (IR OUT). Incoming infrared signals are relayed directly to the receiver.

Point the infrared transmitter towards the target device.

USB keyboard and mouse

• Connect the keyboard and mouse to the “USB K/M” port on the receiver (RX).
• Connect a PC to the “USB PC” port on the transmitter (TX). Use the supplied USB cable.

The keyboard and mouse commands are transmitted to the connected PC, allowing its remote operation.

Installing the audio transmission

HDMI to HDMI

• Audio is transmitted from the transmitter (TX) to the receiver (RX) via HDMI. The receiver and transmitter are connected only via the HDMI cable.

AUX to HDMI

• The audio signal is transmitted from the transmitter’s (TX) AUX IN port to the receiver’s (RX) HDMI OUT port. Use the supplied 3.5 mm audio cable for this purpose.

It is also possible to transmit audio without an image.

HDMI to HDMI/AUX

• The audio signal is transmitted from the transmitter’s (TX) HDMI to the receiver’s (RX) AUX OUT port and the HDMI OUT port. Audio is output via the HDMI and AUX outputs on the receiver.

HDMI/AUX to HDMI/AUX

• The audio signal is sent to the transmitter (TX) via the AUX IN port.
• The audio signal is transmitted to the HDMI OUT and AUX OUT ports on the receiver. Audio signals sent to the transmitter (TX) via the HDMI IN port are not transmitted.

HDMI to AUX

• The audio signal is transmitted from the transmitter’s (TX) HDMI port to the receiver’s (RX) AUX OUT port.
• Connect the supplied 3.5 mm audio cable to the AUX OUT port on the receiver (RX). The AUX-OUT is connected to a TV, active speaker or amplifier.

AUX to AUX

• The audio signal is transmitted from the transmitter’s (TX) AUX IN port to the receiver’s (RX) AUX OUT port.
• Use the supplied 3.5 mm audio cable for this purpose. The AUX OUT port is used to connect a TV, active speakers or amplifier.

Example configurations

HDMI via WLAN

Splitter (1 to N)

Switcher (1 to 1, N to 1)

• Warning: The same channel must be set for the transmitter and receiver.

Troubleshooting

Transmission range may vary depending on the environment. Solid objects such as steel, concrete or brickwork may reduce transmission range or cause signal loss.
Other power-consuming wireless devices or household appliances (e.g. Wi-Fi routers, microwave ovens, air conditioners, etc.) may interfere with the device. Please keep the HDMI receiver and HDMI transmitter away from these sources of interference.

g Ensure there are no signal interferences and you are within transmission range.

g Restart all devices.

g Reset the receiver to factory defaults.

No connection can be established| g Make sure you are within transmission range.

g Restart all devices.

Monitor connected to the receiver (RX) has no signal.| Re-pair receiver (RX) and transmitter (TX):

1.    Switch the RX and TX off.

2.    Set the RX mode switch to SP (splitter).

3.    Set the TX mode switch to SP (splitter).

4.    Switch the RX and TX on.

5.    Connect the TX port HDMI-IN to the RX port HDMI-OUT using an HDMI cable.

è RX and TX start pairing.

è The RX and TX status LEDs STA flash.

6.    Wait until the RX and TX status LEDs STA stop flashing.

è You have re-paired the RX and TX.

è The RX transmits signals to the connected monitor.

Cleaning And Care

Important:

• Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They can damage the housing and can cause the product to malfunction.
• Never immerse the monitor in water or expose it to wetness or increased humidity.
• Use a dry, lint-free cloth to clean the monitor and always switch it off before cleaning it.
• Use a slightly damp or wet cloth or sponge to clean the camera.

Disposal And Declaration

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website): in our Conrad offices at the Conrad collection points at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Declaration of Conformity (DOC)

• Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.
• Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads
• Enter the product item number in the search box. You can then download the EU declaration of conformity in the available languages.

Technical Data

Receiver (RX)

• Rated voltage ………………………………………………………..12 V/DC 1 A
• Dimensions recheiver without antenna (W x H x D) …….166 x 29 x 76 mm
• Dimensions recheiver with antenna (W x H x D) …………166 x 142 x 108 mm
• Weight ………………………………………………………………….283 g

Transmitter (TX)

Rated voltage ………………………………………………………..12 V/DC 1 A
Dimensions transmitter without antenna (W x H x D) …..166 x 29 x 76 mm
Dimensions transmitter with antenna (W x H x D) ……….166 x 142 x 108 mm
Weight ………………………………………………………………….283 g

Infrared receiver

• Cable length ………………………………………………………….147 cm (without plug)

Infrared transmitter

• Infrared transmitter cable length ……………………………….147 cm (without plug)

General information

• Compression …………………………………………………………H.264
• HDMI ……………………………………………………………………HDMI 1.3 and HDCP 1.3
• Latency …………………………………………………………………≤0.3 seconds
• Video format ………………………………………………………….1080p/720p/576p
• Audio format ………………………………………………………….HDMI
• Resolution ……………………………………………………………..max. 1080p/60 Hz
• HDMI port ……………………………………………………………..HDMI Type-A (19-pin female)
• USB-A cable length ………………………………………………..approx. 1150 mm (without plug)
• Operating temperature ……………………………………………0 to +45 °C
• Operating humidity …………………………………………………0 – 80% (non-condensing)
• Storage temperature ……………………………………………….-10 to +60 °C
• Storage humidity …………………………………………………….0 – 80% (non-condensing)

Power adapter

• Input voltage ………………………………………………………….100 – 240 V/AC, 50/60 Hz, 0.5 A
• Output voltage ……………………………………………………….12 V/DC, 1 A
• Cable length ………………………………………………………….147 cm (without plug)

WLAN

• WLAN standard ……………………………………………………..IEEE 802.11a/n/ac, 5 GHz
• Frequency range …………………………………………………..5.180 – 5.240 GHz
• Channel bandwidth …………………………………………………20, 40, 80 MHz
• Transmission power ……………………………………………….max. 16 dBm
• Range …………………………………………………………………..max. 150 m

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing.

Copyright 2024 by Conrad Electronic SE.

References

• Conrad Electronic » Alle Teile des Erfolgs
• Conrad Electronic – Alle Teile des Erfolgs
• Conrad Electronic » All parts of success
• Contact
• Download center
• Conrad Electronic Online Shop » Alle Teile des Erfolgs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>