TCI MINI JOLLY 20 Direct Current Dimmable Electronic Drivers Instruction Manual

TCI MINI JOLLY 20 Direct Current Dimmable Electronic Drivers

Product Information

Specifications

• Brand: MINI JOLLY
• Model: 20 – 1…10 V & PUSH
• Type: Dimmable electronic drivers with DIP-SWITCH
• Origin: Italy
• Weight: 108g / 3.8 oz
• Dimensions: 52mm x 27.5mm x 52mm
• Standards Compliance: CSA, UL, EN, VDE
• Input Voltage: 230V
• Frequency: 50-60 Hz
• Output Current Ripple: 3%
• Standby Power: 0.5W

Product Usage Instructions

DIM-TO-WARM Functionality
The MINI JOLLY drivers support DIM-TO-WARM feature allowing you to adjust light intensity by varying the input voltage between 1 to 10V.

Connection and Installation
Refer to the provided wiring diagram for correct installation. Ensure proper connection of the DIP-SWITCH and PUSH components as per the diagram.

Dimming Settings
To dim the lights, perform the following actions:

• Short push to turn on/off the lights.
• Longer push to increase or decrease light intensity.
• Regulation automatically stops at minimum and maximum values.
• For another on, regulation, or off command, release the push button and give the desired input.

Frequently Asked Questions (FAQ)

• Q: What is the maximum load capacity of the MINI JOLLY drivers?
  A: The maximum load capacity for CB B16A is up to 50 pieces. Please refer to page info17 for more information.

• Q: How can I order accessories like REG 1-10 V or WIRELESS INTERFACES?
  A: You can order accessories like REG 1-10 V with the article code 123999L. For wireless interfaces, please check the available options on the manufacturer’s website.

MINI JOLLY 20 – 1…10 V & PUSH

• Direct current dimmable electronic drivers with DIP-SWITCH

Dimmable multipower drivers – Compact case -1-10V & PUSH

• Rated Voltage
  • 110 ÷ 127 V (2) 220 ÷ 240 V
• Frequency
  • 50-60 Hz
• AC Operation range T
  • AC 99 ÷ 264 V
• DC Operation range
• DC (see page info15)
  • 176 ÷ 280 V
• (NO PUSH mode function)
• Power –
  • 1 ÷ 20 W
  • ≤ 10% (1)
• Stand by power
  • ≤ 0,5 W
• Output current ripple ≤ 3% (1)
• Standards compliance CSA C22.2 no. 223 (2) EN 50172 (VDE 0108) EN 55015
  • EN 61000-3-2
  • EN 61000-3-3
  • EN 61347-1
  • EN 61347-2-13
  • EN 61547
  • EN 62384
  • UL 1310 (2)
  • VDE 0710-T14
• Max. pcs for CB B16A (see page info17)
  • 50 pcs
• In rush current
  • 5A 50µsec

• (1) Referred to Vin = 230 V, 100% load –
• (3) Tc = 75°C for Pout ≤ 16 W
• Pout > 5 W
• (7) 125400BIS – 151400BIS – 125404BIS – 151404BIS:
• order codes for BIS marked products

Accessories not supplied – Accessori non a corredo

Article – Articolo| Code – Codice
REG 1-10 V ( 12.3 )| 123999L
WIRELESS INTERFACES ( W. )| –

Features

•  Multipower driver supplied with dip-switch for the selection of the output current.
• IP20 independent driver, for indoor use (DC MINI JOLLY).
• Class II protection against electric shock for direct or indirect contact (DC MINI JOLLY).
• Driver for built-in use (DC MINI JOLLY BI).
• It can be used for lighting equipment in protection class I and II (DC MINI JOLLY BI).
• Active Power Factor Corrector.
• Current regulation ±5 % including temperature variations.
• Input and output terminal blocks on the same side (wire cross-section up to 1,5 mm2 / AWG15).
• Clamping screws on primary and secondary circuits for cables with diameter: PRI 5-8 mm / SEC 3-5 mm (DC MINI JOLLY).
•   Protections:
  • against overheating and short circuits;
  • against mains voltage spikes;
  • against overloads.
• Thermal protection = C.5.a.

Direct current dimmable electronic drivers with DIP-SWITCH

Wiring diagram

• PUSH diagram
• ADIM diagram

Operation Mode

• Light regulation 0/1 – 100 % by means of PUSH function, 0/1…10 V
• local interface (I=0,35 mA) or 100 Kohm potentiometer.
• (4) Default dimming AM+PWM: 1-25% PWM 2 kHz+25-100% AM.
• (4) Full PWM dimming (240 Hz – 1-100%) and Constant Voltage 12/24V available by removing JP4 on the driver. Enable JP4 to switch to AM+PWM.
• (5) Full AM DIMMING: 1-100%.
• Light regulation 0/1 – 100 % by mains of PUSH function (L mains voltage: 170 Kohm):
  • a short push to turn on and off;
  • a longer push to increase or decrease light intensity;
• regulation automatically stops at minimum and maximum values;
  • for another on, regulation or off command, release the push button and give the desired command again;
  •  dimming level memory at mains restore.
• Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 – 240 Volt mains cable.
• ATTENTION: only use normally open push buttons with no incorporated warning light.
• Specific dimming terminal connection with a 0/1…10 Vdc electronic potentiometer (0/1…10 V local dimming, double insulation required for external connection).

LED Intelligent Driver

• Dimming interface:

• T-PWM digital dimming

• With soft-on and fade in function, visual more comfortable.

• Automatic recognition of 0-10V, 1-10V input signal.

• Dimming range: 0~100%, LED start at 0.01% possible.

• 0-100% flicker-free,High frequency exemption level.

• Innovative thermal management technology, intelligent power life protection.

• Multiple current & wide voltage, suitable for different power LED.

• Non-load output voltage 0V to prevent damages to LED caused by poor contact.

• Short circuit / Over-heat / Over load / Non-load protection, recover automatically.

• Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ

• Up to 50000-hour life time.

• 5 years warranty (Rubycon capacitor).

Super depth dimming technology
Flicker-free
IEEE 1789

• TUV Certificate No. B 17 06 01119 001
• RCM Equipment registration No: E2017013627 Ref: ESV170365
• ENEC Certificate No. U6 17 07 01119 004
• CE
  • EMC Certificate No. BST1702498520001Y-1EC-1
  • LVD Certificate No. BST1709992470001Y-1SC-2

5 in 1 dimming

• 0-10V
• 1-10V
• PWM
• RX
• Push DIM

Model| AD-15-100-700-E1A1| AD-25-150-900-E1A1| AD-36-200-1200-E1A1
---|---|---|---

OUTPUT

| Output Voltage| 10-54Vdc
Max Output Voltage| 58Vdc
Non-load Output Voltage| 0Vdc
Output Current| 100-700mA| 150-900mA| 200-1200mA
Output Power| 1W~15W| 1.5~25W| 2W~36W
Strobe Level| Almost flicker-free / High frequency exemption level.
Dimming Range| 0~100%, LED start at 0.01% possible.
PWM Frequency| ≤3600Hz
Current Accuracy| ±5%
Ripple & Noise| ≤2V

INPUT

| Dimming Interface| 0-10V (1-10V/PWM/RX), Push DIM
Input Voltage Range| 220-240Vac ±10%
Frequency| 50/60Hz
Input Current| <0.15A| <0.2A| <0.3A
Power Factor| PF>0.90/230Vac, at full load| PF>0.93/230Vac, at full load| PF>0.95/230Vac, at full load
THD| ≤20% at 230Vac, at full load
Efficiency(typ.)| 83%| 84%| 87%
Inrush Current(typ.)| Cold start 2.48A at 230Vac

(twidth=25.1μs measured at 50% Ipeak)

| Cold start 2.28A at 230Vac

(twidth=36μs measured at 50% Ipeak)

| Cold start 6.32A at 230Vac

(twidth=60.1μs measured at 50% Ipeak)

Anti Surge| L-N: 1kV
Leakage Current| <0.5mA/230Vac

ENVIRONMENT

| Working Temperature| ta: 50°C tc: 90°C
Working Humidity| 20 ~ 95%RH, non-condensing
Storage Temp., Humidity| -40°C ~ 80°C, 10~95%RH
Temp. Coefficient| ±0.03%/°C (0-50°C)
Vibration| 10~500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes.

PROTECTION

| Over-heat Protection| Intelligently adjusting or turning off the output current if the PCB temperature ≥110°C, , auto recovers.
Over Load Protection| Shut down the output when rated power≥102%, auto recovers.
Short Circuit Protection| Shut down automatically if short circuit occurs, auto recovers.
Non-load Protection| Shut down the output if no load, auto recovers when load back to normal.

SAFETY & EMC

| Withstand Voltage| I/P-O/P: 3750Vac
Isolation Resistance| I/P-O/P: 100MΩ/500VDC/25°C/70%RH
Safety Standards| IEC/EN61347-1, IEC/EN61347-2-13
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2,3,4,5,6,8,11  EN61547
Strobe Test Standard| IEEE 1789

OTHERS

| Dimension| 167×41×32mm(L×W×H)
Packing| 168×43×35mm(L×W×H)
Weight(G.W.)| 165g±10g
Model| AD-15-100-700-E1A1| AD-25-150-900-E1A1| AD-36-200-1200-E1A1
---|---|---|---

OUTPUT

| Output Voltage| 10-54Vdc
Max Output Voltage| 58Vdc
Non-load Output Voltage| 0Vdc
Output Current| 100-700mA| 150-900mA| 200-1200mA
Output Power| 1W~15W| 1.5~25W| 2W~36W
Strobe Level| Almost flicker-free / High frequency exemption level.
Dimming Range| 0~100%, LED start at 0.01% possible.
PWM Frequency| ≤3600Hz
Current Accuracy| ±5%
Ripple & Noise| ≤2V

INPUT

| Dimming Interface| 0-10V (1-10V/PWM/RX), Push DIM
Input Voltage Range| 220-240Vac ±10%
Frequency| 50/60Hz
Input Current| <0.15A| <0.2A| <0.3A
Power Factor| PF>0.90/230Vac, at full load| PF>0.93/230Vac, at full load| PF>0.95/230Vac, at full load
THD| ≤20% at 230Vac, at full load
Efficiency(typ.)| 83%| 84%| 87%
Inrush Current(typ.)| Cold start 2.48A at 230Vac

(twidth=25.1μs measured at 50% Ipeak)

| Cold start 2.28A at 230Vac

(twidth=36μs measured at 50% Ipeak)

| Cold start 6.32A at 230Vac

(twidth=60.1μs measured at 50% Ipeak)

Anti Surge| L-N: 1kV
Leakage Current| <0.5mA/230Vac

ENVIRONMENT

| Working Temperature| ta: 50°C tc: 90°C
Working Humidity| 20 ~ 95%RH, non-condensing
Storage Temp., Humidity| -40°C ~ 80°C, 10~95%RH
Temp. Coefficient| ±0.03%/°C (0-50°C)
Vibration| 10~500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes.

PROTECTION

| Over-heat Protection| Intelligently adjusting or turning off the output current if the PCB temperature ≥110°C, , auto recovers.
Over Load Protection| Shut down the output when rated power≥102%, auto recovers.
Short Circuit Protection| Shut down automatically if short circuit occurs, auto recovers.
Non-load Protection| Shut down the output if no load, auto recovers when load back to normal.

SAFETY & EMC

| Withstand Voltage| I/P-O/P: 3750Vac
Isolation Resistance| I/P-O/P: 100MΩ/500VDC/25°C/70%RH
Safety Standards| IEC/EN61347-1, IEC/EN61347-2-13
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2,3,4,5,6,8,11  EN61547
Strobe Test Standard| IEEE 1789

OTHERS

| Dimension| 167×41×32mm(L×W×H)
Packing| 168×43×35mm(L×W×H)
Weight(G.W.)| 165g±10g

Dimensions

LED Current Selection
Quick options: DIP switch for 8 optional currents’ quick selection ( see the table below ).

•  After current setting by DIP switch, power off and then power on to make the new current effective.
• E.g. LED 3.2V/pcs: 10-54V can power 3-16pcs LEDs in series, 10-22V can power 3-6pcs LEDs, the max quantity of LEDs in series will be subject to the actual voltage of LED.

Wiring Diagram

Push Dimming

• On/off control: Short press.
• Stepless dimming: Long press.
• With every other long press, the light level goes to the opposite direction.
• Dimming memory : Brightness will be the same as previously adjusted when turning off and on again.

Relationship Diagrams

Flicker Test Form

• Marks in the right chart were tested results of different current ranges.
• The output frequency is 0Hz in 100% brightness and its corresponding modulation is 0%, which could not be shown in the right chart.

SWITCH TO BRIGHTER FUTURE
Product data sheet: LIM-12D

Features

• Independent design
• Dimmable constant current driver
• Low ripple current,flicker-free
• DALI-2 certified
• Configurable constant current output via dip-switch
• Switch-Dim function
• Dimming range 0.1…100%
• Push wire connections
• Protections: opencircuit, shortcircuit, overload, overtemperature
• SELV equivalent
• Suitable for use in emergency lighting systems
• Suitable for protection class II luminaires
• Protection class II
• Nominal life-time up to 50,000 h
• 5-year guarantee

Applications

• Office
• Shop
• Hospitality
• Public areas

Approbations & Certifications

• CE,CB,DALI-2

Housing properties

• Housing material: plastic, white.
• Type of protection IP20

Electrical Specifications

INPUT

| Nominal voltage| V| 220 – 240
Nominal frequency| Hz| 0 / 50 / 60
AC voltage range| V| 198 – 264
DC voltage range| V| 176 – 370
Nominal current| A| 0.08
THD (Full load)| %| ≤ 25
Power factor (Full load)| | 0.90C
Efficiency (Full load)| %| 80
NO load| W| ≤ 0.5
Protection class| | II
Inrush current(Cold start)| A pk| 15(th = 100 μs)
Max.units per circuit breaker| | B10: 46 B16: 74 C10: 93 C16: 149

OUTPUT

| Nominal voltage range| V| 2 – 42| 2 – 42| 2 – 42| 2 – 40| 2 – 22| 2 – 20| 2 – 18| 2 – 17
Maximum voltage(Open Circuit)| Vdc| ≤ 54
Nominal current| mA| 150| 200| 250| 300| 550| 600| 650| 700
Current accuracy| %| +/- 5
Current ripple 100Hz| %| ≤ 20
Pst LM| | ≤ 1
SVM| | ≤ 0.4
Nominal power range| W| 0.3 – 6.3| 0.4 – 8.4| 0.5 – 10.5| 0.6 – 12| 1.1 – 12| 1.2 – 12| 1.3 – 12| 1.4 – 12
Maximum power| W| 12
Galvanic isolation| | SELV

ENVIRONMENT

| Ambient temperature range ta| °C| -20 …+45
Maximum case temperature tc| °C| 85
Max. Case temp. In fault contdition| °C| 110
Storage temperature range| °C| -20 …+70
Relative humidity| %| 5 … 85 (Not condensing)
Surge transient protection| kV| 1 | 2  (L/N | LN/PE acc to. EN 61547 Clause 5.7)
Environmental rating| | Indoor
IP rating| | IP 20
Mains switching cycles| | > 100,000
Expected lifetime| ****

h

| 50,000（0.2% / 1’000 h failure rate）

All parameters NOT specially mentioned are measured at 230VAC input ,rated current and 25 of ambient temperature

Protections

• Over temperature
  • Yes
• Over load
  • Yes
• No load
  • Yes
• Short-circuit
  • Yes
• Input overvoltage
• Maximum allowed input voltage 264V AC Output overvoltage
• Yes, Limitation of Output voltage < 54V

The graph is for reference only and the detailed values refer to the parameter table

Wiring Diagram

• Terminal: Captured terminal screws
• Max. cable length – DALI system: 300 m
• Dimensions(LxWxH): 132x30x20 mm
• Mounting hole spacing，length 126.3 mm
• Weight: 110 g

• PRI

• Cable cross-section: 0.75-2.5□/AWG 18-14

• Stripping: 6mm

• SEC

• Cable cross-section: 0.5-1.5□/AWG 20-16

• Stripping: 6mm

• Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs.

• Remarks

• Touch current : lower than 0.7 mA, according to EN 60598-1 annex. G and EN 61347-1 annex A

• Standards

• EN 61347-1

• EN 61347-2-13

• EN 62384

• EN 55015

• EN 61000-3-2

• EN 61000-3-3

• EN 61547

• EN 60598-1

• EN 62386-101

• EN 62386-102

• EN 62386-207

• EN 62386-209

• IEE1789

• (EU) 2019/2020

Product data sheet: IE-45D
Features

Independent design

• Dimmable constant current driver
• Low ripple current.flicker-free
• DALl-2 certified
• Configurable constant current output via dip-switch
• Switch-Dim function
• Dimming range 0.1 … 100%
• Push wire connections
• Protections: opencircuit, shortcircuit, overload, overtemperature
• SEL V equivalent
• Suitable for use in emergency lighting systems
• Suitable for protection class 11 luminaires
• Protection class II
• Nominal life-time up to 50,000 h
• 5-year guarantee

Applications

• Office
• Shop
• Hospitality
• Public areas

Approbations & Certifications

• CE,CB,DALl-2

Housing properties

• Housing material: plastic, white.
• Type of protection IP20

Electrical Specifications

OUTPUT

| Nominal voltage range| V| 25-70| 25-70| 25-70| 25-64| 25-56| 25-50| 21-43
Maximum voltage(Open Circuit)| Vdc| ,;; 80
Nominal current| mA| 350| 500| 600| 700| 800| 900| 1050
Current accuracy| %| +/- 5
Current ripple 100Hz| %| ,;; 20
Psi LM| | ,;; 1
SVM| | ,;;0.4
Nominal power range| w| 9-24.5| 12.5-35| 15-42| 17.5-45| 20-45| 22.5-45| 22.5-45
Maximum power| w| 45
Galvanic isolation| | SELV
ENVIRONMENT

| Ambient temperature range ta| oc| -20 … +50
Maximum case temperature tc| oc| 85
Max. Case temp. In fault contdition| oc| 110
Storage temperature range| oc| -20 … +70
Relative humidity| %| 5 … 85 (Not condensing)
Surge transient protection| kV| 1 12 (LIN I LN/PE ace to. EN 61547 Clause 5.7)
Environmental rating| | Indoor
IP rating| | IP 20
Mains switching cycles| | > 100,000
Expected lifetime| ****

h

| 50,000 (0.2% I 1’000 h failure rate)

All parameters NOT specially mentioned are measured at 230VAC input ,rated current and 25°C of ambient temperature

Protections

• Over temperature
  • Yes
• Over load
  • Yes
• No load
  • Yes
• Short-circuit
  • Yes
• Input overvoltage
• Maximum allowed input voltage 264V AC
• Output overvoltage
• Yes, Limitation of Output voltage < 80V

The graph is for reference only, and the detailed values refer to the parameter table

• Terminal: Push in terminals
• Max. cable length – DALI system: 300 m
• Dimensions (LxWxH): 135x72x24 mm
• Weight: 180 g

PRI

• Cable cross-section: 0.75-2.5/AWG 20-14
• Stripping: 8mm

SEC

• Cable cross-section: 0.5-2.5 /AWG 20-14
• Stripping: 8mm
• Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs.

Remarks

Touch current: lower than 0.7 mA, according to EN 60598-1 annex. G and EN 61347-1 annex A

Standards

• EN 61347-1
• EN 61347-2-13
• EN 62384
• EN 55015
• EN 61000-3-2
• EN 61000-3-3
• EN 61547
• EN 60598-1
• EN 62386-101
• EN 62386-102
• EN 62386-207
• EN 62386-209
• IEE1789
• (EU) 2019/2020

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>