The Home Depot RH4FBL3PW LED White Selectable Strip Light Instruction Manual
- June 1, 2024
- THE HOME DEPOT
Table of Contents
The Home Depot RH4FBL3PW LED White Selectable Strip Light
Specifications:
- Dimming Functions: 0/1-10VDC, PWM signal, Variation of resistance unit
- Recommended Dimmers: LUTON NTSTV-DV, LEVITON DS710-10Z / IP710,LEGRAND
- Wiring Instruction: L (Black), N (White), Green/Yellow DIM + DIM (Refer to light label for wire color of DIM+ and DIM-)
- CCT Tunable: 30K/35K/40K/50K
Product Usage Instructions
Installation Precautions:
Before installing the LED strip light, ensure the following precautions are
taken:
- Turn off the power supply before installation or maintenance.
- Ensure proper earth grounding for safety.
- Check for any shipping damage and contact the manufacturer if necessary.
Dimming Functions:
This product supports 3 dimming functions: 0/1-10VDC dimming,PWM signal
dimming, and Variation of resistance unit dimming.
Choose the appropriate dimming method based on your requirements.
CCT or Wattage Tunable:
Adjust the wattage or CCT (Correlated Color Temperature) by following these
steps:
- Press the screws on both sides of the lamp to open it.
- Adjust wattage by dialing as needed.
Installation Methods:
This product supports two installation methods: Surface Mounting and Hanging.
Surface Mounting:
- Drill holes at corresponding positions based on product length.
- Drive rubber plugs into the holes.
- Clamp the disc to the lamp.
- Lead the wire into the lamp and connect wires according to safety requirements.
- Install the lamp body back to the chassis.
LED Strip Installation Instructions
Cautions
- Can not use the electric generator to test the LED light.
- Please abide by related country, regional and local law and regulations when install this fixture.
- Please turn off the power before installation or maintenance.
- Proper earth grounding is required to ensure safety.
Notice
- To avoid possibility of electrical shock or fire, the installation personnel must have professional electric knowledge.
- Please wear gloves to avoid injury before installation.
- If any smoke or spark of the wire happened, please turn off the power immediately and notify relevant personnel.
Attention
- Please check if there is any damage during shipping. If so, please contact manufacturer timely.
- Please read the installation instruction carefully to check whether all the accessories are complete. After confirmation, then install the fixture according to installation steps.
Wiring Diagram & Instruction
3 dimming functions are available in this high bay light
- Constant current can be achieved by 0/1-10VDC dimming
- PWM signal dimming
- Variation of resistance unit dimming.
Description:
This product is 0/1-10V dimming,below dimmers are recommened:
Brand| Model
LUTON| NTSTV-DV
LEVITON| DS710-10Z / IP710
LEGRAND| RH4FBL3PW
Wiring Instruction
- L: Black
- N: White
- : Green/Yellow
- DIM +
- DIM –
(As for the wire color of DIM+ and DIM-, pls check the light label.)
Please choose the appropriate dimming way according to your needs.You can also
choose not to use this function.
Round lampshade or square lampshade will not affect the installation method or
function expansion of the product.
CCT or Wattage Tunable
Step1. Press the screws on both sides of the lamp by hand to open the lamp, Wattage can be adjusted via dialing.
Two installation methods: A Surface Mounting, B Hanging
(Please choose the most suitable installation method for the purchased product
as per your needs.)
Surface Mounting
Step 1. According to the different lengths of the product, drill holes at the corresponding positions and drive the rubber plugs from the accessory kit into the holes (Figure 1)
Step 2. Clamp the disc from the accessory kit to the lamp (this step can be omitted if the light fixture can completely cover the junction box on the wall) (figure 2)
Step 3. Press the screws on both sides of the lamp by hand to open the lamp (Figure 3)
Step 4. Lead the wire into the lamp and install the lamp chassis by using the screws in the accessory kit (figure 4)
Step 5. Connect the wires according to safety requirements, and then install the lamp body back to the chassis, By using a extra mounting bracket, the lights can be connected in series (Figure 5) (Product connection: 20W lamps can be connected to maximum 50pcs, 40W 20pcs, and 60W 12pcs, and 100W 6pcs)
Hanging Installation
Step 1. Hang one end of the installation rope in the accessory kit on the wall or hook (Choose accessories according to your needs) (Figure 6)
Step 2. Fasten the other end of the installation rope to the lamp (Figure 7)
Step 3. Press the screws on both sides of the lamp by hand to open the lamp.
Step 4. Connect the wires according to safety requirements, and then install the lamp body back to the chassis (Figure 8)
Extra Accessory Option Installation:
- Product lengthening,
- Sensor,
- Backup driver, 4: Wire Guard.
Product lengthening
Step 1. Use the screws in the accessory kit to lock the bracket onto one lamp (figure 9) Step 2. Align the other lamp to the bracket and lock the screws (Figure 10) (Product connection: 20W lamps can be connected to maximum 50pcs, 40W 20pcs, and 60W 12pcs, and 100W 6pcs).
AC PIR Sensor
Step 1. Press the screws on both sides of the lamp by hand to open the lamp.
Step 2. Assemble the PIR sensor onto the lamp (Figure 11), connect the wires according to the wiring instructions, and then assemble the disassembled lamp back. (Figure 12)
DC Motion Sensor
Step 1. Press the screws on both sides of the lamp by hand to open the lamp.
Step 2. Assemble the DC sensor to the corresponding position (Figure 13).
Step 3. Connect the wires according to the wiring instructions,adjust sensing mode as per demand, and then assemble the disassembled lamp back. (Figure 14)
Backup driver
Step 1. Press the screws on both sides of the lamp by hand to open the
lamp.
Step 2. Assemble the backup driver to the lamp chassis (Figure 15)
Step 3. Connect the wires according to the wiring instructions, and assemble the disassembled lamp back. (Figure 16)
Wire Guard
After installing the product is completed, install the barbed wire on the lamp
with screw.(Figure 17/18)
Frequently Asked Questions (FAQ)
Can I use an electric generator to test the LED light?
No, it is not recommended to use an electric generator for testing. Please refer to professional electric knowledge for installation.
What should I do if there is smoke or spark from the wire during installation?
Immediately turn off the power and notify relevant personnel to address the issue.
How many lamps can be connected in series?
For product connection, 20W lamps can be connected to a maximum of 50pcs, 40W to 20pcs, 60W to 12pcs, and 100W to 6pcs.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>