NoDon 2-FP-21 Module Chauffage Fil Pilote User Guide

NoDon 2-FP-21 Module Chauffage Fil Pilote

Specifications

• Product Name: Module Chauffage Fil Pilote
• Function: Heating Module with Pilot Wire
• Language: French (FR)

Installation

1. Ensure the power source is switched off before installation.
2. Connect the heating module to the pilot wire following the provided instructions.
3. Mount the module securely in a suitable location.
4. Turn on the power and follow the setup procedure detailed in the manual.

Operation

1. Set the desired temperature using the control interface.
2. The module will regulate the heating output based on the temperature settings.
3. Monitor the system for any unusual behavior and refer to troubleshooting if needed.

Maintenance

1. Regularly check for dust accumulation and clean the module as necessary.
2. Inspect the pilot wire connections for any loose fittings or damage.
3. Keep the surrounding area clear to ensure proper ventilation for the module.

FAQ
Q: Can I use this heating module with any type of pilotwire?
A: It is recommended to use the specified pilot wire compatible with the module for optimal performance.

PILOT WIRE HEATING MODULE

• Reference: SIN-2-FP-21
• Power supply: 230V AC ~ 50Hz
• Consumption: <1W
• Heater maximum power: 3680 W
• Metering of Instant power (W) and cumulated
• Energy (Wh) – compatible home automation gateway
• needed (see the “Support” section on nodon.fr)
• Pilot wire management: 6 modes
• Radio frequency range: 868.0 to 868.6 Mhz
• RF power max: +10dBm
• Range: up to 30m indoor

Operational temperature

• The SIN withstands ambient temperatures :
  • Between -20 and 40° in the open air.
  • Between -20 and 35°C in a flush-mounted box.
  • Between -20 and 40°C in the NodOn DRB (Din Rail Box).
  • Between -20 and 40°C in the NodOn BPS (Surface-Mounted Box).
• Protection rating: IP 20
• Pairing: up to 18 controllers
• EEP (EnOcean Profile): D2-01-0C
• Dimensions: 41 mm (l) x 44 mm (L) x 16.9 mm (h)
• Weight: 29 g
• Warranty: 2 years

USE CAUTIONS

• Never use the device if it is not correctly installed and placed inside a connecting box in conformity with the current norms.
• Keep the product far away from liquids.

CONTACT

• NodOn SAS
• 121 rue des Hêtres
• 45590 St CYR EN VAL
• (FRANCE

AFTER SALES SERVICE

nodon.fr/en/ “support” section support@nodon.fr

PRODUCT SUPPORT

Go directly to the product support page at nodon.fr/sin-2-fp-21

SOPORTE DE PRODUCTOS

Vaya directamente a la página de soporte del producto en nodon.fr/sin-2-fp-21
PRODUKT-SUPPORT
Gehen Sie direkt zur Supportseite des Produkts auf nodon.fr/sin-2-fp-21

APPROVALS AND CERTIFICATIONS

Hereby, NodOn SAS declares that this radio equipment is conform to the RED directive 2014/53/UE. The integral text of the EU declaration of conformity is available at the following online address: nodon.fr/en/ ”support” section.
The presence of this symbol on a product indicates that this one is conform to the European directive 2012/19/UE. Find out more about the provisions in force in your region regarding the separate collection of electrical and electronical devices. Respect the local rules and do not  throw out the product with common domestic wastes. The correct rejection of ancient products allows to preserve the environment and health.

This product must be used indoor only.
The device is used 20 cm or more from the human body.
This product is conform to EnOcean radio protocol.

DANGER OF ELECTROCUTION

BEFORE ANY INSTALLATION MAKE SURE THE POWER SUPPLY IS DISCONNECTED TO AVOID ANY RISK OF ELECTROCUTION.

Directly cut the power supply from the breaker box to avoid any risk of electrocution. This relay switch is designed to be used power up, a wrong installation can create a fire or an electric shock. If you are not confident about electrical installation, please ask a professional.
The relay switch must be installed and connected carefully following the instructions of this user guide. We will not be responsible for any loss or damage resulting from a non-respect of the instructions of this user guide. Cut the power supply before any operation and don’t do any modification if the LED is still ON.

INSTALLATION

NodOn Pilot Wire Heating Module allows to connect any type of pilot wire heater to a compatible EnOcean network. Thanks to its compact size, the Pilot Wire Heating Module can be installed behind the grommet of  the pilot wire heater.

TIP

Add the Pilot Wire Heating Module to the electric panel with NodOn DIN Rail Box.
Optional accessory

MODULE INPUTS/OUTPUTS

Each terminal can accept a cable of 2.5mm² maximum, stripped of 8mm.

INSTALLATION DIAGRAM

1. Cut the power supply.

2. Dismantle the grommet connecting your pilot wire heater.

3. Cable the module according to diagram figure 1.
   Warning: Make sure the pilot wire of your heater is well connected on the FP terminal before turning the power supply back ON.

4. Reinstall the grommet.

5. Turn the power supply back ON.

USE
During the first power up, the module default state is “Comfort” and the LED is green.

To change the mode, press briefly once on the button.

*Incrementation of the 4 module’s modes:**

The module LED will blink to confirm the activation of thenext mode:

• Comfort Eco: LED blinks orange once
• Eco No Frost: LED blinks orange twice
• No Frost Stop: LED blinks orange 3 times
• Stop Comfort: LED blinks orange 4 times

*Note: Used with a home automation gateway, 6 modes are available: Comfort, Comfort -1°C, Comfort -2°C, Eco, No Frost and Stop. To change the mode, follow the instructions of your home automation gateway.

PAIRING PROCEDURE
To add a remote or a wall switch (EnOcean compatible) you must enter the pairing mode.
Module must be power supplied.

1. Launch the pairing by doing 3 consecutive presses (<2 seconds) on the module button.
   The LED blinks red.

2. You have 30 seconds to pair your controller by briefly pressing (in less than a second) on the button of your choice.
   

3. The LED of the module will blink green twice, confirming the pairing of the two devices.

Note: if the LED blinks orange during the pairing procedure, it means that more than 18 controllers are paired and that no more controller can be paired. You must remove one controller to add a new one.

CONTROLLER USE
Your remote works by channel.

Your wall switch works by channel.

USE OF YOUR SOFT BUTTON
To pair your Soft Button with the module

1. Launch the module pairing mode (see “Pairing Procedure”)
2. You have now 30 seconds to pair your Soft Button by doing 5 brief consecutive presses on the button.
3. The LED of the module will blink green twice, confirming the pairing of the two devices.

The Soft Button will work as follows:

PAIRING WITH A HOME AUTOMATION GATEWAY

For more details on how to pair a home automation gateway or other compatible products, please consult the “Support” section on nodon.fr/en/

UNPAIRING PROCEDURE
Do the same procedure as pairing (see “Pairing procedure”).

RESET PROCEDURE
Module must be power supplied.

1. Press more than 5 seconds on your module’s button. The LED blinks orange.
2. Press once again the button (short press) to confirm the reset. If the reset is correct, the LED blinks alternatively in red and green and stays green. Start again if necessary.
3. Your module has now its original settings.

References

• Fabricant domotique OBL - OEM - ODM pour la Maison Connectée
• Fabricant domotique OBL - OEM - ODM pour la Maison Connectée
• Smart Home & Building - OEM ODM OBL solutions for IoT products
• Technical Support NodOn | Product documentation, tutorial, use cases
• Supports Archive - NodOn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>