VOLLRATH 0644N Tomato Pro Tomato Slicer Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 0644N Tomato Pro Tomato Slicer
Product Information
Specifications:
- Product Models: Tomato ProTM, Econo ProTM, Tomato KingTM
- Usage: Blade replacement and adjustment
- Safety Feature: Pusher head fingers must never contact blades
Product Usage Instructions
Blade Replacement:
- Ensure safe installation and operation by reading and understanding all instructions.
- Handle sharp blades with caution to avoid injury.
- Do not mix old and new blades in the same assembly to prevent excessive blade breakage.
- Wash new blades with warm, soapy water and rinse thoroughly before installation.
- Follow the parts diagram for your equipment when changing blade assemblies.
- Dispose of used blades and assemblies properly.
Adjustments:
- Examine pusher head fingers for nicks or burrs; smooth rough edges with a small flat file.
- Straighten any bent fingers and ensure uniform spacing between them.
- Center the new blade assembly with the sharp side facing the pusher head.
- Replace screws and rubber seals, ensuring the bottom blade fits between the two bottom-most pusher head fingers.
FAQ
Q: What should I do if the pusher head fingers contact the blades?
A: If there is contact between the pusher head fingers and blades, adjustments must be made. Carefully adjust the position of the pusher head fingers using a screwdriver as described in the manual.
Q: Can I reuse old blades in the assembly?
A: It is not recommended to mix old and new blades in the same assembly as this may lead to excessive blade breakage. We suggest changing the complete assembly for optimal performance and safety.
Q: How should I handle sharp blades?
A: Handle sharp blades with caution. Only trained personnel should operate equipment or perform maintenance. Keep the sharp edge away from you when handling blades to avoid cuts and injuries.
Blade Replacement and Adjustment for the Tomato ProTM, Econo ProTM and Tomato KingTM
To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the warning is
ignored.
REPLACING BLADE ASSEMBLY
WARNING
Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal
should operate equipment or preform maintenance.
We suggest you change the complete assembly. Never mix old and new blades in
the same assembly as this may lead to excessive blade breakage.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin
protective oil film. Keep the sharp edge away from you when handling blades.
- Allow yourself ample room to work on a flat, dry surface. Familiarize yourself with the parts diagram for your equipment. Blade assemblies consist of blades, blade blocks, blade block pins, rubber seals, and screws.
- When changing blade assemblies on the Tomato King, close the pusher head so that the pusher head fingers are through the blades resting against the pin stop.
- When changing blade assemblies on the Tomato Pro and Econo Pro equipment, pull the pusher head assembly back away from the blades so it is against the back stop.
- To remove blade assemblies, use the proper tool to remove the four blade block screws (2 at each end). Retain the rubber seals that are mounted on the screws between the blade blocks and the casting.
- Dispose of used blades and blade assemblies properly.
ADJUSTMENTS
- Examine the pusher head fingers. If they are nicked or burred, smooth the rough edges with a small flat file. The spaces between the fingers must be uniform. Straighten any bent fingers.
- Center the new blade assembly between bridge casting posts with the sharp side facing the pusher head. Replace screws and rubber seals. Be certain that the bottom blade fits between the two bottom-most pusher head fingers.
- Check the clearance between the pusher head fingers and blades. Make sure they do not rest on or touch the blades at any point when you move the head through its full travel. If there is contact, adjustments must be made. Pusher head fingers must never contact blades.
To adjust Pusher Head Fingers between blades:
- Carefully insert a screwdriver (B) between the slots in the Pusher Head Assembly (A). Gently tap on the screwdriver (B) (up or down) to alter the location of the Pusher Head Fingers so the slide effortlessly through the blades. See Figure 1.
- It may also be necessary to adjust the Pusher Head Assembly (A) from the back side of the equipment, as well. If needed, carefully insert a screwdriver (B) between the slots in the Pusher Head Assembly. Gently tap on the screwdriver
(B) (up or down) to alter the location of the Pusher Head Fingers so they slide effortlessly through the blades. See Figure 2.
Adjust the Pusher Head Assembly through the Blades:
- Momentarily loosen set screws to the guide rods to adjust the location of the Pusher Head Assembly by pushing/pulling on the guide rod. Once the Pusher Head Assembly is properly located, tighten the set screws. See Figure 3.
Tightening the blades:
Blades must be tightened in alternating sequence
-
Keep blade assembly centered between casting end-posts with a gap of air space between the blade block and post.
-
Tighten screws one-half turn at a time in the following order:
A. Top Right – 1/2 Turn
B. Bottom Left – 1/2 Turn
C. Bottom Right – 1/2 Turn
D. Top Left – 1/2 Turn -
Repeat this sequence until the screws are tight. Check for proper blade tightness by strumming the dull side of the blade to identify a uniform vibration.
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830 Fax: 800.752.5620
Technical Services: 800.628.0832 Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2014 The Vollrath Company, L.L.C.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>