LINEAR HAE00072 Smart WiFi Wall Station Instruction Manual
- June 6, 2024
- LINEAR
Table of Contents
Manufactured by:
Nortek Security and Control, LLC
760-438-7000
www.nortekcontrol.com
Linear Smart Wi-Fi Wall Station (HAE00072)
Programming / Installation Instructions
This Wi-Fi wall station allows direct operation of the door operator and light
using the buttons. When connected to your local wireless access point, you can
check status, get notifications, open or close the door, and manage user
access from any location via the Linear Android or iOS app.
Requirements
To use with the app you will need:
- a Wi-Fi network with internet connectivity
- a strong Wi-Fi signal in the garage where you are installing the wall station
- an Android or iOS smartphone or tablet.
See page 5 for instructions on downloading and installing the Linear garage door app.
Wi-Fi Wall Station Functions
Printed in China for Nortek Security and Control, LLC.Copyright© 2020 Nortek
Security and Control, LLC
10029898 Rev-A
Installing the Wi-Fi Wall Station
Test Wi-Fi Signal Strength
Before you affix the Wi-Fi wall station to the wall, survey your location to
check the Wi-Fi signal. To do this, take your smartphone or tablet, connect it
to your Wi-Fi network and then place your device on the wall where you want to
attach the wall station.
If you have 2 or 3 bars on your device for the Wi-Fi network, the signal is
strong and you can proceed. If not, use one of these options to extend your
Wi-Fi network’s range.
- Move your Wi-Fi router closer to the garage.
- Purchase a Wi-Fi range extender.
The Wi-Fi wall station must receive a strong signal from your home’s Wi-Fi router to work.
Choose Placement of Wall Station
The wall station is typically mounted inside the garage on the wall adjacent
to the door into the house. Wall the station can be mounted in any convenient
place on a drywall-covered wall with wood studs and filled with blown-in or
batt insulation.
If possible, avoid affixing the wall station:
- to a solid brick or concrete walls
- to metal studs or walls with metal inside
- on top of or near AC electrical lines.
Mount Wall Station
Follow the instructions in the diagram to the right
See page 3 to connect the wall station to your mobile device through the Linear app.
IMPORTANT
Wire polarity is critical with the Wi-Fi wall station.
Wire the Wall Station
Always unplug the opener head unit’s AC power cord before wiring or
repositioning the wall station!
Connect the wall station to the garage door opener head unit using either the
supplied or pre-existing wires.
Use the wire that has a mark to connect the COMMON (COM) terminals. Make sure
that you connect the COM terminal on the wall station to the COM terminal on
the garage door opener head unit.
Next, connect the WALL STATION (WS) terminal on the wall station to the WALL
STATION (WALL) terminal on the garage door opener head unit.
Test the Wall Station
Once you have connected the wall station to the garage door opener head unit,
test if working properly by using the wall station to operate the light and
door by taking the following steps.
• Plug the garage door opener head unit’s AC power cord back into an outlet.
• Wait a few moments until the LED on the wall station comes on.
• Press the light button to turn the light on and off.
• Press the cycle door button to operate the door. If you are unable to
operate the garage door using the wall station’s buttons, please go to the
Troubleshooting guide on page 6.
Using the Wall Station
Vacation Lock for Additional Security
1 Open the wall station’s cover to access the Programming Buttons. Press the
VACATION LOCK ( ) button to prevent remote controls from opening the door
after the door is
completely closed. When the Vacation Lock is activated, the remote controls
can close the door, but not open it. The door can still be opened or closed by
using the wall station’s UP/ DOWN ARROW pushbutton.
NOTE: To signal that the vacation switch is locked, the opener’s light
will flash and the alarm will sound five times if remote control is activated
in an attempt to open the door.
2 Press the wall station’s VACATION LOCK ( ) button again to unlock and return
the operator to normal operation.
Wall Station Reset
If you change your home router or password you will need to RESET your Wall
Station.
1 To do a Wall Station RESET press the WiFi Link ( ) button for 10 seconds,
the RED LED blinks and then turns solid RED. The Wall Station is now ready to
re-link to a new or updated home router.
2 To re-boot the Wall Station for software updates, press the RESET ( )
button.
Controlling the Opener’s Light
- The opener’s light can be turned ON by pushing the wall station’s on/off ( ) button. The light will stay on until the button is pressed again or the opener is cycled.
- To DECREASE the light brightness press the dimmer( button.
- To INCREASE the light brightness press the brighter button.
LED Lights on the Wall Station
The Wi-Fi wall station has two LED lights that convey information at a glance.
Linear app Installation
Download, Register and Activate Application
Use your smartphone or tablet to visit your app store to download and install
the Linear application. On initial use, you’ll be asked to register and create
an account. Once complete, sign in with your new account information.
Connect the Opener to the app Stand near the Wi-Fi wall station. On your mobile device in the Linear app, after creating your place (i.e your home, or barn, or vacation home) tap the plus sign at the bottom right of the screen to Connect Your Device. Follow directions in-app to Connect Your Device.
Use the Linear app
The app’s main screen indicates the current state of the garage door and
allows operation. If your garage door is fully closed, the app will show the
door fully closed. If the garage door is partially or fully open, the app will
show the door open.
To close or open the garage door, tap the garage door icon. Likewise, tap the
light icon to turn the garage door light on or off.
For a detailed view of the device, tap a device icon. From here you can adjust
the brightness of the light, and you can view a history of who operated the
device.
Manage Your Devices and Members
Tap the Site Menu icon (three circles stacked on top of each other) located in
the top left of the screen. From here you can remove devices from your site,
invite new members to join your site, and remove existing members from your
site.
Invite Others
To invite a new member, select the Invite New Member button at the bottom of
the Site Menu. You will be asked to set their permission level. There are
three classes of members in this application:
- You, the Linear app administrator, created the site and added devices.
- Administrators, who can invite others, set/ change permissions, and operate and view all devices.
- Regular members, who can operate and view only specified devices.
TROUBLESHOOTING GUIDE
Condition/LED Color| Possible Cause| Possible Solution
The Wall station does not power on.| 1. Incorrect wiring| 1. Check wall
station wiring for correct polarity.
2. Confirm the head unit is plugged in and has power.
3. Call tech support.
RED| 1. Wall station has not been as- signed to an access point.
2. Wall station is not within range of its assigned access point.
3. Antenna interference.| 1. Use the mobile app to configure the wall
station’s access point.
2. Relocate the wall station or relocate the home’s access point.
3. Ensure the area around the wall station is free from metal objects and
electrical wires. Refer-
ence page 2 of this manual for checking Wi-Fi signal.
YELLOW| 1. Checking for updates| 1. No action is required from the user;
this behavior is normal and temporary.
WARNING: Changes, modifications or adjustments not expressly approved by
Nortek Security and Control, LLC could void the
user’s authority to operate this equipment. There Are No User Serviceable
Parts.
NOTICE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
NOTICE: This device complies with part 15 of the FCC. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Manufactured by:
Nortek Security and Control, LLC
760-438-7000
www.nortekcontrol.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>