VOLLRATH 15018 3.5 Blade Replacement Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 15018 3.5 Blade Replacement
Specifications:
- Model: Table Top Model / Wall Mount Model
- Blade Type: Sharp blades for cutting food products
- Material: Stainless steel blade assembly
- Dimensions: Varies based on model
- Weight: Varies based on model
Product Usage Instructions
1. Safety Precautions: Handle sharp blades with caution to prevent cuts and injuries. Only trained personnel should operate the equipment.
Blade Installation:
- Remove the pusher head assembly based on the model type.
- Raise the bumpers approximately 2 inches (5.0 cm).
- Carefully remove the old blade assembly by loosening the thumbscrew.
- Install the new cutting blade assembly securely and tighten the thumbscrew.
Assembly Alignment: Slide bumpers down guide rods, position pusher head assembly, and check alignment before use.
Maintenance: Lubricate the guide bar with mineral oil or Petrol-Gel after each use to ensure smooth operation.
FAQ
Q: Can I use cooking oil for lubrication? A: No, do not use cooking oil as it may damage the equipment. Use mineral oil or Petrol-Gel for lubrication.
Q: How often should I replace the cutting blade assembly? A: Replace the cutting blade assembly when it becomes dull or damaged for efficient cutting performance.
Installation Instructions
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal
should operate equipment or preform maintenance.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.
-
Remove the pusher head assembly:
Tabletop models: Slide the pusher head off the rod guides.
Wall mount models: Remove the locking pin (J). Lift handle and slide the pusher head off the guide rods. Place pin back into the hole on the handle assembly to prevent loss.- A Guide Rods. Guides and align the pusher head onto the blade set.
- B Handle. Used to lower and raise the pusher head block
- C Guides. Used for smooth and consistent operation of pusher head on the guide rods
- D Pusher Head Assembly. Made up of the pusher head block (and “T” handle for tabletop models).
- E Bumpers. Cushions the stop of the pusher head.
-
Raise the bumpers approximately 2” (5.0 cm).
-
Loosen thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
-
Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
-
Slide bumpers down guide rods to contact base assembly. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.
-
Lubricate the guide bar with mineral oil or Petrol-Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
-
F Thumbscrew. Used to secure the pusher head block or the blade assembly.
-
G Pusher Head Bock. Pushes the food product through the blade set.
Specifically sized to match the corresponding blade assembly. -
H Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block
-
I Base Assembly. Holds the guide rods and blade assembly.
-
J Locking Pin. Secures the pusher head to the handle.
-
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A. Main Tel: 800.624.2051 or 920.457.4851 Main
Fax: 800.752.5620 or 920.459.6573 Customer Service: 800.628.0830 Canada
Customer Service: 800.695.8560
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036 Countertop Warming Products: 800.354.1970 All
Other Products: 800.628.0832
© 2016 The Vollrath Company L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>