Anker 522 Portable Power Station User Manual

Anker 522 Portable Power Station

Product Usage Instructions

• Charging the Power Station
  To recharge the power station, use the provided DC input port with a compatible charger. Follow the provided specifications for input wattage to ensure safe and efficient charging.

• Using the Power Station

  • For USB-A and USB-C ports, devices can be plugged in for automatic charging. Unplugging the devices will turn off charging automatically.
  • The car socket and AC output port require manual activation using the corresponding on/off buttons before charging.
  • Keep Power Saving Mode turned on to avoid unnecessary power drain, except when charging low-powered devices like CPAP machines or cameras.

• Power Saving Mode
  Switch on Power Saving Mode to automatically turn off the power station when all devices are fully charged. This helps prevent wastage of power. Turn off Power Saving Mode for stable charging over extended periods.

• Flashlight Mode
  To use the ambient light, press the button once. Hold the button for 2 seconds to activate SOS mode in case of emergencies.

• Troubleshooting
  If the power station malfunctions, perform a factory reset by inserting a paper clip or pin into the reset hole for 1 second. If issues persist, contact support for assistance.

FAQ

Q1: What's the maximum power output of the AC port?

A1: The max power output of the AC port is 300W. Devices exceeding this limit will trigger an automatic shutdown.

Q2: Can I recharge the product while charging connected devices?

A2: Yes, you can recharge the product while charging connected devices.

Q3: Can this product power a CPAP?

A3: Yes, this product can power a CPAP machine. Remember to disable Power Saving Mode when using it for CPAP machines.

Q4: Will this product lose power automatically if not powered off?

A4: Yes, when the car socket or AC control button is turned on, even without connected devices, there will be some power consumption. It's advisable to keep Power Saving Mode on except for specific device charging needs.

Q5: What kind of solar charger can charge this product?

A5: Any 11V-28V solar charger with a DC 8mm (DC 7909) male connector can charge this product.

Overview

Recharging

• Please fully charge the product before using it for the first time
• When your portable power station only has 1% battery remaining, the indicators will flicker to remind you to recharge the device.

Charging

1. The USB-A and USB-C ports support plug and charge. When devices are plugged in, they will start charging automatically; when devices are unplugged, they will turn off automatically.
2. The car socket and AC output port do not support plug and charge. Use the corresponding on/off buttons to turn them on before charging.
3. To avoid draining the battery, we recommend keeping Power Saving Mode turned on except when you are charging low-powered devices like CPAP machines and cameras.

Power Saving Mode

• Switching on the power saving mode prevents wasting power by automatically turning off the Power Station once all your devices are fully charged.
• Switching off the power-saving mode will enable stable charging over an extended period, such as for time-lapse photography or for sleeping with a CPAP machine.

LCD Screen Guide

1. Power Saving Mode

2. High-Temperature Alert
   When this icon shows, stop using the product and leave it to cool down until the icon disappears.

3. Low-Temperature Alert
   When this icon shows, stop using the product until the icon disappears.

4. USB-C Input/Output Port

5. USB-A Output

6. Car Charging

7. AC Charging and Voltage Frequency

8. Remaining Battery

9. Remaining Battery in Hours

10. Current Input Power

11. Current Output Power

Flashlight Mode

Press the button once to turn on the ambient light

Hold the button for 2 seconds lo turn on SOS mode.

Troubleshooting

Resetting Your Power Station

If your Power Station isn’t working correctly, insert a paper clip or pin into the reset hole for 1 second for a factory reset. If the Power Statton still doesn’t work, please contact support@anker.com.

Specifications

Attention
Not permitted on aircraft.

IMPORTANT SAFETY INSTRUCTIONS

WARNING
When using this product, basic precautions should always be followed, including the following:

Read all the instructions before using the product.

• To reduce the risk of injury, close supervision is necessary when the product is used near children.
• Do not put your fingers or hands into the product.
• Do not expose the product to rain or snow.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
• To reduce the risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the product.
• Do not use the product above its output rating. Overload outputs above the rating may result in a risk of fire or injury to persons.
• Do not use a product that is damaged or modified Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not operate the product with a damaged cord or plug, or a damaged output cable.
• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.
• Do not be exposed to fire or high temperatures. Exposure to fire or temperatures above 130°C may cause an explosion.
• To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed servicing.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained
• When charging a device, the product may feel warm, this is a normal operating condition and should not be cause for concern.
• When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
• Do not clean the product with harmful chemicals or detergents
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other
• Do not use or store the power station in direct sunlight for an extended period, such as in a car, cargo bed, or any other place where it will be exposed to high temperatures. Doing so may cause the product to malfunction, deteriorate, or generate heat.
• Do not use the product for applications such as data servers or medical equipment where a malfunction in an emergency could seriously endanger human life or property.

Storage and Maintenance instructions

1. Store the product between 32°F-104 °F (0°C-40°C). Avoid exposing the product to rain or using the product in a humid environment.
2. To preserve the battery lifespan, charge to 100% after use. If you plan to store your power station, recharge to 100% every 3 months.
3. Keep the product on a flat surface when using, charging, and storing.

FCC Statement

This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

The following importer is the responsible party.

• Company Name: Fantasia Trading LLC
• Address  5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
• Telephone:+ 1-800-988-7973

IC Statement

• This Class B digital apparatus complies with Canadian ICES-003.
• This digital apparatus complies with CAN ICES-003 (B)/NMB-003(B)

Customer Service

• support@anker.com
• support.mea@anker.com (For Middle East and Africa Only)
• (US/CA) + 1 (800)988 7973
• (UK) +44 (0) 1604 936200
• (DE)
  • +49(0)69 9579 7960
  • +49 (800) 0002522 (Anker SOLIX)
• (Middle East & Africa) +971 520750842
• (UAE) +971 8000320817
• (KSA) +966 8008500030
• (Kuwait) +965 22069086
• (Egypt) +20 8000000826
• (AU) +61 3 8331 4800
• (TR) +90 0850 460 14 14
• (RU) +8 (800) 511-86-23
• (India) +91 18003138831

For FAQs and more information, please visit:
anker.com/support.

For tutorial videos, FAQs, manuals, and more information, please visit:
https://support.anker.com

Or scan the QR code below:

Warranty

Warranty Card
Register and activate your warranty and priority customer service.

Anker Portable Power Station’s Warranty Policy

• All Anker portable power stations purchased on AnkerDirect and Anker authorized resellers come with a limited warranty (“warranty”) as set out below. By using an Anker portable power station, you are agreeing to be bound by the terms of the Anker limited warranty.
• We provide a 5-year limited warranty for purchases made on AnkerDirect and Anker authorized resellers. The warranty period starts from the date of purchase.
• Anker:s limited warranty is restricted to the country of purchase. The limited warranty is void on items taken outside the country they were originally bought in or shipped to directly from an authorized online purchase.

Exclusions and Limitations
Not covered under warranty:

• Products that are damaged or modified.
• Products operated with a damaged cord, plug, or output cable.
• Products that are disassembled.
• Products that are cleaned with harmful chemicals or detergents.
• Non-quality related issues (after 30 days of purchase).
• Products purchased from unauthorized resellers.
• Products without sufficient proof of purchase.
• Products that have been refunded.
• Products with an expired warranty.
• Lost, stolen or complimentary items.
• Damage from outside sources.
• Repairs through 3rd parties.
• Damage from misuse of products (including, but not limited to falls, use of the product over its output rating, exposure of the product to rain or snow, extremely low air pressure, and extreme temperatures).
• Purchases from illegitimate resources.
• Batteries that are damaged when not used for a long time or not properly maintained according to the user manual.

Anker is Not Liable For:

• Loss of data incurred from the use of Anker products.
• Returning personal items sent to Anker.

When returning items with a prepaid shipping label provided by Anker, Anker takes responsibility for any damage or loss incurred in transit. When returning items for non-quality issues, the buyer assumes responsibility for any damage or loss incurred in transit. Anker does not provide refunds for items damaged in transit due to non-quality-related warranty claims.

• For warranty claims, you can send an email to:
• US/CA/UK/DE/JP: support@anker.com
• MEA: support.mea@anker.com
• CN: CED-CN@anker.com.

Or you can call us at:

• US/CA:+ 1 800-988-7973
• UK: +44 (0) 1604 936 200
• DE: +49 (0) 69 9579 7960
• UAE: +971 8000 320 817
• KSA: +966 8008 500 030
• Kuwait: +965 2206 9086
• AU: +61 3 8331 4800
• TR: +90 (850) 460 1414
• RU: +8 (800) 511 8623
• JP: +81 03 4455 7823
• Egypt: +20 8000 000 826
• CN: +86 400 0550 036
• KR: +82 02-1661-9246
• IN: +91 1800 3138831
• Middle East & Africa: +971 520 750 842

This page is attached to the Anker warranty page, and Anker reserves the right to final interpretation of the content.

Register Your Anker PowerHouse Today

Why Register?

1. Hassle-Free Warranty: Confirm the 5-year warranty for your Anker PowerHouse.
2. Fast Customer Service: Enjoy exclusive customer service and get what you need quickly.
3. Receive the Latest News: Get exclusive first looks at new products and instant updates on official events.

Scan the QR code below to enter the smart self-service page for more information about your PowerHouse.

Why Registering Matters

Contact Us

• US/CA/UK/DE/JP support@anker.com
• MEA support.mea@anker.com
• CN CED-CN@anker.com
• Learn More https://support.anker.com.

Just scan and register to activate your 5-year warranty with priority customer service.

Scan the QR code below to enter the smart self-service page for more information about your PowerHouse.

51005003905 V02

References

• Anker Support
• Anker Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>