SEALEY DCDST Diamond Core Drills Stand Instruction Manual

DCDST Diamond Core Drills Stand
Instruction Manual DIAMOND CORE DRILLS STAND
MODEL NO: DCDST

DCDST Diamond Core Drills Stand

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR  WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 

SAFETY

Only use on firm, level, unobstructed surfaces which are capable of supporting the stand and drill.
Ensure stand is fixed to surface capable of supporting stand, drill and work piece.
Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.
‰ WARNING! Failure to comply with these instructions may result in damage to the stand or other property and/or personal injury.
‰ WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which  cannot be built into this product, but must be applied by the operator

INTRODUCTION

Lightweight aluminium diamond core drill stand features tilting mechanism and base plate with anchor fitting. Handle and wheels for ease of
transport. Ideal for use with Model No’s DCD110V and DCD230V Diamond Core Drills.

SPECIFICATION

Maximum Drill Bit Diameter:………………………………. Ø200mm
Travel Length:……………………………………………………. 600mm

OPERATION

4.1. ATTACHING DRILL TO STAND REF. FIG 1
4.1.1. The drill is attached to the stand using the drill clamp (fig.1)
4.1.2. Remove one half of the drill clamp by means of the screws, slot the drill into place and replace the clamp.
4.1.3. Secure the clamp by using the two locking handles.
4.2. SECURING STAND TO THE GROUND
4.2.1. To bolt the stand to the ground, drill a hole for a securing bolt a suitable distance away from your intended drilling area.
Note: You do have some adjustment on the drill base but plan before you drill.
4.2.2. The base can be levelled using the 4 levelling bolts. Adjust these before securing the anchor bolt.
4.3. SETTING THE ANGLE
4.3.1. Loosen the angle adjustment bolt and the brace locking handle, slide up or down until you get the desired angle

MAINTENANCE

5.1. Keep clean, remove the spatter from the cradle guide channels.

TROUBLESHOOTING

Clean the machine thoroughly and reassemble the drill and check for run-out again.

ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:** Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park,
Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk ****www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
LP100.V7 Issue 3 (H,2,3) 19/04/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>