ROPEFLEX RXP2 Stationary Pulley Bracket User Manual
- June 1, 2024
- ROPEFLEX
Table of Contents
ROPEFLEX RXP2 Stationary Pulley Bracket
Specifications
- Model: PULLEY SYSTEM 32-4110 REV.B
- Maximum User Weight: 300 pounds
Product Information
The PULLEY SYSTEM is a versatile fitness equipment designed to provide a comprehensive workout experience. It includes various components such as pulley assembly, slider rail, hardware, and safety features to ensure a safe and effective exercise routine.
Product Usage Instructions
Assembly Instructions
- Identify all components listed in the Box Contents section of the manual.
- Follow the PULLEY SYSTEM ASSEMBLY INSTRUCTIONS & MANUAL for step-by-step guidance on assembling the equipment.
- Ensure all parts are securely tightened before each use.
Important Precautions
- Read all instructions in the manual before using the equipment.
- Only use the equipment on a level surface and ensure proper floor protection.
- Avoid children under 12 and pets near the equipment during operation.
- Check and replace any worn parts immediately.
Safety Guidelines
- Always wear athletic shoes for foot protection while exercising.
- Avoid grabbing the rope in a way that prevents the drum from rotating.
- If you experience pain or dizziness during exercise, stop immediately and cool down.
FAQ
- Q: Where can I find the serial number of the product?
- A: The serial number is located on the equipment or on the box. If not found, please check the equipment itself.
- Q: What is the maximum weight capacity of the PULLEY SYSTEM?
- A : The equipment is designed to support a maximum user weight of 300 pounds.
PLEASE REGISTER YOUR NEW PRODUCT
To register your product online please go to:
www.ropeflex.com/warranty-and-registration
The product serial number is located on the equipment or is shown in the box below
SERIAL NUMBER
If a serial number is not shown please check the equipment
WARNING DECAL PLACEMENT (IF APPLICABLE)
The decals shown here have been placed on the equipment in indicated locations. If any of the decals are missing or illegible, call us toll-free at 650.549.5888, Monday through Friday, 9 a.m. until 5 p.m. Pacific Time, to order replacement decals. Apply replacement decals in the locations shown.
CAUTION
PINCH POINTS KEEP HANDS CLEAR NO LOOSE CLOTHING OR LONG HAIR NEAR THE ROTATING DRUM
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions before using this equipment.
- Read all instructions in this manual and assemble as described before using this equipment.
- It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of all precautions.
- Use this equipment only on a level surface. Cover the floor beneath to protect the surface.
- Keep children under 12 and pets away from the equipment at all times.
- Make sure all parts are properly tightened each time you use this machine. Replace any worn parts immediately.
- Make sure the adjustment knobs are fully engaged / disengaged before using the equipment.
- Always wear athletic shoes for foot protection while exercising.
- This equipment is designed to support a maximum user weight of 300 pounds.
- Pull on one the rope only and never grab a rope in a way that prevents the drum from rotating. Never attempt to hang on the rope or frame. Pull rope with hands only.
- If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ROPEFLEX assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
Box Contents
ITEM/ QUANTITY /DESCRIPTION
- 1/ 1/ PULLEY SYSTEM ASSEMBLY
- 2 /1 /PULLEY SLIDER RAIL
- 3 /2/ Zinc Locknut, 3/8″-16
- 4 /20/ 3/8″ Washer
- 5 /2 /Steel Socket Head Screw 3/8″-16 x 3.75″
- 6 /2/ Spacer for Rail Mounting Screw
- 7 /4/ Steel Socket Head Screw 3/8″-16″ x 1″
- 8 /2/ Steel Socket Head Screw 3/8″-16 x 4.5″
- 9 /4/ Oversized Washer for 3/8″ Screw Size
- 10 /2/ Wall Bracket
- 11 /2/ ½” Washer
- 12 /4/ ½” x 2.5” Wood Screw
PULLEY ASSEMBLY Parts List
ITEM QUANTITY DESCRIPTION
- 1/ 1/ PULL PIN
- 2/ 1/ SHELVE PLASTIC
- 3/ 1/ Lock Nut 1/2″-13″
- 4/ 1 /Lock Nut 3/8″-16″
- 5 /4 /Lock Nut 5/16″-18″
- 7 /4 /SLIDES
- 8/ 1/ PULL KNOB
- 10 /1 /PULLEY HANDLE (OPTIONAL)
- 11/ 1 /MAIN STEEL BRACKET
- 12/ 4 /Shoulder Screw
- 13/ 1 /Hex Nut 1/2-13″
- 14/ 3 /Washer 1/2″
- 15/ 2/ Washer
- 17 /1/ CARRIAGE BOLT
Tools Required for Installation (Not Included)
9/16″ Hex Socket (for Part #3 and also to Remove/Attach PULLEY SYSTEM HANDLE)
5/16″ Hex Key (for Part #12 and also to Remove/Attach bottom bolts of SLIDER RAIL)
Product Installation
STEP 1 to 4 for Configuration 1
1-1 If using existing rack holes, please follow these instructions: install Steel Socket Head Screw 3/8″-16 x 4.5″, spacer, washer, and nut into the bottom rack holes first. Use the 5/16″ hex key. Slide the pulley assembly in through the top of the slider rail and proceed to install screw, spacer, washer, and nut into the top rack holes in the same configuration as the top. When installing the slide rail using existing rack holes, refer to the following figure for suggested install configuration.
1-2 If not using existing rack holes, drilling is necessary. Please follow these instructions: measure a distance of 37 in. and drill clearance holes for 3/8″ fasteners into existing rack. Fasten the bottom first of the sliding rail as shown below using 5/16″ hex key using the fasteners included. Slide pulley assembly through top of rail and then fasten the top of sliding rail as shown below.
1-3 To keep rope from being free from pulley system, remove only the handle using a 9/16″ Hex Socket and position rope within (as shown below). Re- attach the handle in your desired direction.
1-4 Tighten all screws.
Sample Configuration 1
Sample Configuration 2
Sample Configuration 3 – Wall installation with brackets
Equipment Maintenance
WARNING: Routine inspection and maintenance is of critical importance to ensure maximum safety and performance. We use the highest quality materials available, but wear is inevitable. Be advised that dangerous conditions can arise even during a warranty period. A warranty does not negate the owner’s responsibility to thoroughly, carefully and daily inspect the machine. Consult your physician before starting your exercise program. For your own safety, do not begin any exercise program without proper instruction.
Check Rope
While the machine is not in use carefully inspect the rope for damage and tears. Carefully inspect the connection of rope ends and make sure that stitching (threads) are not torn or damaged. Do not use equipment until damaged rope has been replaced.
Upholstery
Wipe down after every workout. Periodically take the time to use a mild soap or mild vinyl upholstery cleaner. Avoid using any abrasive cleaner not intended for use on vinyl. Keep sharp or pointed objects out of your pockets and clear of all upholstery.
Nuts/Bolts/Fasteners
Periodically inspect all nuts and bolts. Tighten if needed. If bolts seem to loosen periodically, use Loctite 242 for a long-term cure. Go through a re- tightening sequence periodically to ensure that all hardware is properly tensioned.
Adjustments / Locking Pins / Tightening Knobs
Check all pieces for signs of visible wear or damage. Check springs in Snap Links and Pop Pins for proper tension and alignment. If the spring sticks or has lost its rigidity, replace it immediately.
Anti-Skid Surfaces
Replace if they appear worn or become slippery.
Warning Instruction Labels
Inspect and familiarize yourself with all safety warnings and other user information on decals. Replace decals if damaged, illegible, or removed.
Warranty
We strive to offer the simplest and fastest resolution to all product-related concerns. Our warranty service program gives its customers the option to return the product for repair, exchange or refund if the product is determined to be defective.
-
All products are warranted to the original purchaser.
-
Warranties apply and cover all defects in material and workmanship.
Frame (excluding coating): Lifetime
Rope, Sheaves, Bearings and Labor: One-Year -
The customer is responsible for the cost of shipment to ROPEFLEX. Company “ship to” address for product returns and service will be provided once the RMA has been issued. It will be at ROPEFLEX’s discretion to determine the party responsible for cost of shipment back to the customer.
-
Out-of-warranty products are repaired only with the customer’s prior approval.
-
15-Day 100% Satisfaction Guarantee includes a full refund of the purchase price, less shipping, handling and restocking fee equaling 15% of price during purchase. Email for more details. If you decide to return a ROPEFLEX product, simply email us within 15 days to ask for a return authorization number (RMA). Items must be returned in original condition and packaging and postmarked no later than 2 weeks after the date of return authorization.
If you have any questions regarding ROPEFLEX equipment or any instruction found in this document, please call 650.549.5888 for assistance