ROPEFLEX RX2500D Dual-Station Oryx Rope Trainer Instruction Manual

ROPEFLEX RX2500D Dual-Station Oryx Rope Trainer

Product Specifications

• Model: RX2500
• Maximum User Weight: 300 pounds

Product Usage Instructions

Assembly Instructions
Follow the steps below to assemble your RX2500:

1. Step 1 (Standard RX2500 Configuration)
   Parts Required: RX2500 Seat support plate, RX2500 Seat stand, ORYX Seat Hardware Required: Screws (Qty. 8), Washers (Qty. 4)
   Tools Required: Philips #2 Screw Driver

2. Attach RX2500 Seat support plate to RX2500 Seat stand.

3. Install and completely tighten the screws.

4. Attach item from step 1-2 to ORYX Seat.

5. Install and completely tighten the hardware (use screw & washer).

6. Step 2 (for Hipervision enabled RX2500)
   Parts Required: RX2500 Main Mast, Base
   Hardware Required: Screws, Washers
   Tools Required : Philips #2 Screw Driver

7. Attach RX2500 Main Mast to Base as shown and completely tighten the hardware.

8. Use leveling shims as required by placing them between the base and main mast bottom bracket.

Important Precautions

• Read all instructions in the manual before using the equipment.
• Ensure that all users are informed of safety precautions.
• Use the equipment on a level surface and protect the floor beneath it.
• Keep children under 12 and pets away from the equipment.
• Check and tighten all parts before each use, replacing any worn parts immediately.
• Ensure adjustment knobs are fully engaged/disengaged before use.
• Wear athletic shoes for foot protection during exercise.
• Avoid grabbing the rope in a way that prevents drum rotation or attempting to hang on the rope.
• If you experience pain or dizziness while exercising, stop immediately.

Frequently Asked Questions (FAQ)

• Q: Where can I find the serial number of the product?
  A: The serial number is located on the equipment or in the box below SERIAL NUMBER. If not found, please check the equipment.

• Q: What should I do if any warning decals are missing or illegible?
  A: Contact us at 650-549-5888 to order replacement decals. Apply replacement decals in the indicated locations.

PLEASE REGISTER YOUR NEW PRODUCT
To register your product online please go to: www.ropeflex.com/warranty-and- registration
Product serial number is located on equipment or is shown in the box below

SERIAL NUMBER
If serial number is not sown please check equipment

ORYX – RX2500
Assembly Instructions & Manual DOC: 32-1016
Configuration subject to change

WARNING DECAL PLACEMENT

The decals shown here have been placed on the equipment in indicated locations. If any of the decals are missing or illegible, call us toll-free at 650-549-5888, Monday through Friday, 9 a.m. until 5 p.m. Pacific Time, to order replacement decals. Apply replacement decals in the locations shown.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions before using this equipment.

1. Read all instructions in this manual and assemble as described before using this equipment.
2. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of all precautions.
3. Use this equipment only on a level surface. Cover the floor beneath to protect the surface.
4. Keep children under 12 and pets away from the equipment at all times.
5. Make sure all parts are properly tightened each time you use this machine. Replace any worn parts immediately.
6. Make sure the adjustment knobs are fully engaged / disengaged before using the equipment.
7. Always wear athletic shoes for foot protection while exercising.
8. This equipment is designed to support a maximum user weight of 300 pounds.
9. Pull on one the rope only and never grab a rope in a way that prevents the drum from rotating. Never attempt to hang on the rope. Pull rope with hands only.
10. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-  existing health problems. Read all instructions before using. ROPEFLEX  assumes no responsibility for personal injury or property damage sustained by  or through the use of this product.

Contents / Parts List

Tools Required for Assembly

• 3/8 Hex Key
• 3/16 or 1/4 Hex Key for 5/16” Button
• 5/16 Hex Key for 3/8” or ½” Socket Head Screws

Product Assembly

STEP 1 (Standard RX2500 Configuration)

• Parts :
  • RX2500 Seat stand
  • RX2500 Seat
• Hardware :
  • Button Head Screw 5/16” x 1”
  • Washer 5/16”
• Tools:
  • 3/16 or 1/4 Hex Key for 5/16” Button Head Screws

1. Attach RX2500 Seat support plate to RX2500 Seat stand.
2. Install and completely tighten hardware (use screw only).
3. Attach item from step 1-2 to ORYX Seat (Box 2).
4. Install and completely tighten hardware (use screw & washer).

STEP 2 (for Hipervision enabled RX2500 refer to page 11)

• Parts:
  • RX2500 Main Mast
  • RX2500 Base
  • RX2500 Seat Assembly
• Hardware:
  • Button Head Screw 5/16” x 1”
  • Washer 5/16”
• Tools:
  3/16 or 1/4 Hex Key for 5/16” Button Head Screws

1. Attach RX2500 Main Mast to Base as shown and completely tighten hardware (use screws and washers). Use leveling shims as required by placing between base and main mast bottom bracket.
2. Attach RX2500 Seat Assembly to RX2500 Base as shown and completely tighten hardware (use screws and washers). 

Product Assembly (GEN 2)

STEP 3

• Parts:
  • Assembly from STEP 2
  • RX2500 Rope Drum
• Hardware:
  • Button Head Screw 5/16” x 1”
  • Washer 5/16”
• Tools:
  3/16 or 1/4 Hex Key for 5/16” Button Head Screws

1. Tilt assembly from STEP 2 and lay it down as shown.
2. Attach RX2500 Rope Drum to assembly from STEP 2 and completely tighten hardware on both sides (use screws and washers).
3. Attach sensor cable from the Drum to the connector on the RX2500 Main Mast. Ensure full insertion, most of the time a “click” will be heard and felt.
4. Tilt machine back up to a standing position.

Product Assembly (GEN 3)

STEP 3.A

• Parts:
  • Assembly from STEP 2
  • RX2500 Rope Drum
• Hardware:
  • Button Head Screw ½-13” x 1”
  • Washer ½”
• Tools:
  • 5/16 Hex Key for ½-13” Button Head Screws

1. Tilt assembly from STEP 2 and lay it down as shown.

2. Attach sensor cable from the Drum to the connector on the RX2500 Main Mast. Ensure full insertion, most of the time a “click” will be heard and felt.

3. Tuck cable and connected connectors inside the mast and attach RX2500 Rope Drum to assembly from STEP 2. Fully tighten hardware on both sides (use screws and washers).
   TAKE EXTRA CARE NOT TO DAMAGE SENSOR CABLES DURING THIS PROCESS

4. Tilt machine back up to a standing position.

Product Assembly – Pulley Assembly (REVISION A)

STEP 4.A

• Parts:
  • Assembly from STEP 3
  • RX2500 Pulley Assembly
• Hardware:
  • Button Head Screw 7/16” x 5/8”
  • Washer 7/16”
• Tools:
  3/8 Hex Key for 7/16” Socket Screws

1. Attach Pulley Assembly to assembly from STEP 3 and completely tighten hardware (use screws and washers).

2. Attach optional pulley assemblies along the mast, removing filler set screws as required. Product Assembly – Pulley Assembly (REVISION B)
   STEP 4.B

   • Parts :
     Assembly from STEP 3
     RX2500 Pulley Assembly REV.B

   • Hardware :
     Socket Head Screw 3/8-16 or 5/16-18

   • Tools:
     5/16 Hex Key for 3/8” Socket Head Screws or
     3/16 or 1/4 Hex Key for 5/16” Button

3. Attach Pulley Assembly REV B. to assembly from STEP 3 by sliding it from top of the rail as shown below. Use pull pin to fix pulley in different positions.

4. Install “stop screw” as shown and tighten it with an appropriate hex key

Product Assembly – LCD Display (GEN 1)

STEP 5

• Parts:
  • Assembly from STEP 4
  • Display Bracket
  • LCD Display
• Hardware:
  • Button Head Screw 5/16” x 1”
  • Washer 5/16”
  • Thread Forming #4-20 Screw
• Tools:
  • 3/16 or 1/4 Hex Key for 5/16” Button Head Screws
  • Philips #2 Screw Driver

1. Attach Display Bracket as shown and tighten hardware (use screws and washers).

2. Remove bottom screw from LCD display, mount display on bracket and install Thread Forming #4-20 Screw.
   Do not over-tighten screw to avoid stripping newly formed plastic threads

3. Attach sensor connector from RX2500 Mast to newly installed LCD Display.

Product Assembly – Hipervision enabled RX2500 (GEN 2)

If the RX2500 was purchased with the Hipervision Bluetooth module please review the following installation procedure while performing STEP 2 on page 6 Tools :

• 3/16 or 1/4 Hex Key for 5/16” Button Head Screws
• 9/64 Hex key for #8-32 battery cover screws

STEP 2.1

1. Connect male sensor cable connector to female receptacle on the RX2500 base. Ensure good connection. Electrical tape may be used but is not required to prevent connectors from separating.
2. Assemble main mast as shown and secure it with screws.
3. Battery cover is secured by 2 screws. RX2500 ships with batteries preinstalled. Remove cover only to replace batteries.

Product Assembly – Hipervision enabled RX2500 (GEN 3)
GEN 3 Hipervision enabled RX2500 machines integrate the wireless module inside the main mast. Battery port can be accessed from the back of the machine as shown.

Equipment Maintenance

WARNING: Routine inspection and maintenance is of critical importance to ensure maximum safety and performance. We use the highest quality materials available, but wear is inevitable. Be advised that dangerous conditions can arise even during a warranty period. A warranty does not negate the owner’s responsibility to thoroughly, carefully and daily inspect the machine. Consult your physician before starting your exercise program. For your own safety, do not begin any exercise program without proper instruction.

1. Check Rope
   While the machine is not in use carefully inspect the rope for damage and tears. Carefully inspect connection of rope ends and make sure that stitching (threads) are not torn or damaged. Do not use equipment until damaged rope has been replaced.

2. Upholstery
   Wipe down after every workout.
   Periodically take the time to use a mild soap or mild vinyl upholstery cleaner. Avoid using any abrasive cleaner not intended for use on vinyl.
   Keep sharp or pointed objects out of your pockets and clear of all upholstery.

3. Nuts/Bolts/Fasteners
   Periodically inspect all nuts and bolts. Tighten if needed. If bolts seem to loosen periodically, use Loctite 242 for a long-term cure.
   Go through a re-tightening sequence periodically to ensure that all hardware is properly tensioned.

4. Adjustments / Locking Pins / Tightening Knobs
   Check all pieces for signs of visible wear or damage.
   Check springs in Snap Links and Pop Pins for proper tension and alignment.
   If the spring sticks or has lost its rigidity, replace it immediately.

5. Anti-Skid Surfaces
   Replace if they appear worn or become slippery.

6. Warning Instruction Labels
   Inspect and familiarize yourself with all safety warnings and other user information on decals. Replace decals if damaged, illegible, or removed.

WARRANTY

We strive to offer the simplest and fastest resolution to all product related concerns. Our warranty service program gives its customers the option to return the product for repair, exchange or refund if the product is determined to be defective.

• All products are warranted to the original purchaser.
• Warranties apply and cover all defects in material and workmanship.
  • Frame (excluding coating): Lifetime
  • Rope, Sheaves, Bearings and Labor: One-Year
• Customer is responsible for the cost of shipment to ROPEFLEX. Company “ship to” address for product returns and service will be provided once the RMA has been issued. It will be at ROPEFLEX’s discretion to determine the party responsible for cost of shipment back to customer.
• Out-of-Warranty Products are repaired only with the customer’s prior approval.
• 15 Day 100% Satisfaction Guarantee includes full refund of purchase price, less shipping, handling and restocking fee equaling 15% of price during purchase. Email for more details. If you decide to return a ROPEFLEX product, simply email us within 15 days to ask for a return authorization number (RMA). Items must be returned in original condition and packaging and postmarked no later than 2 weeks after the date of return authorization.

If you have any questions regarding ROPEFLEX equipment or any instruction found in this document, please call 650-549-5888 for assistance.

References

• Warranty and Registration | ROPEFLEX - Strength & Conditioning Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>