RFID01 Module

“`html

Product Information

Specifications

• Operates at: 13.56 MHz
• Maximum field strength: 64.666 dBuV/m @ 3m
• Power supply: 3V3 dc (+/- 10%) via J1 connector

Product Usage Instructions

Installation Guide for Host Manufacturers

This installation guide is intended for expert technicians and
host manufacturers to ensure proper installation of the WALLBOX
RFID01 module.

1. Unpack the module and attach the supplied cables if
   necessary.

2. Dismount the final product and prepare it to assemble the
   module.

3. Ensure there is enough space in the device for easy
   installation without affecting other electronics.

4. Install the module inside the host device ensuring the final
   position.

5. Connect the pins or cables as indicated.

Additional Considerations:

• Ensure proper fit of the device within the final product
  without interference with other electronics.

• Use provided cables for installation; contact customer service
  if necessary.

• Power WALLBOX RFID01 module with a 3V3 dc supply.

• Avoid covering PCB antenna with conductive material.

Integration Instructions for Host Product Manufacturers

Refer to KDB 996369 D03 OEM Manual v01 for detailed integration
instructions, including compliance with FCC rules and operational
use conditions.

Compliance

The WALLBOX RFID01 module is approved by the FCC and IC for use
in various end-products. It must not operate with other antennas or
transmitters to ensure proper functionality.

Communication Interface

Overview

The Reader can be controlled using a simple protocol over SPI as
specified by NXP for its CLRC663 IC.

Marking and Labelling of the Product

The product shall contain specific information as silkscreen
printing and labeling as instructed.

FAQ

What power supply should be used for the WALLBOX RFID01

module?

The module must be powered by a 3V3 dc supply through the J1
connector.

Can I cover the PCB antenna with conductive material?

No, avoid covering the PCB antenna with any conductive material
to ensure proper functionality.

“`

User Manual- Wallbox RFID01 module
1 Installation Essential Instructions and Requirements for Users of this Product and Host Equipment Containing This Product
This product has been approved by the Federal Communications Commission (FCC) and Industry Canada (IC). It is accredited as Modular Approval for radio modules under regulations detailed in 47 CFR 15.225 and RSS-210 issue 10 Annex B6. The product is only for use with a 3V3 dc (+/- 10%) power supply to it via the J1 connector shown in Picture 1 below.
Picture 1
The host power supply to the product should be rated to be able to deliver up to 500 milliamps of in rush current for up to 100 milliseconds and supply a constant current of up to 200 milliamps. This product is only authorised for operation using the integral trace antenna contained on the product. It is not authorised for use with any other antenna. RF exposure calculation has been provided with the module certification utilising a worst case 20cm distance to users, RF exposure in the host equipment may need to be re-evaluated. Host equipment incorporating this product must have clearly affixed to it a permanent label stating, “Contains FCC ID: 2BB8L-RFID01” and “Contains IC ID: “31519-RFID01”. The host equipment containing this product must itself be tested and verified that it does not exceed the FCC rules in 47 CFR part 15.225 or RSS-210 Annex B6 including if the host equipment is powered by a mains AC supply, that it does not exceed the AC powerline conducted emissions limits specified in the FCC / RSS-GEN test specifications. A host manufacturer has three options available, either: 1) A Class II permissive change (FCC) or a Class IV permissive change (ISED) must be requested Through Wallbox in order to add the host equipment test evaluation data to the existing certification. 2) The host manufacturer can perform a change in ID followed by a class II permissive change. 3) The host manufacturer can apply for a new FCC ID or IC ID. This product is only authorised for the following rule: Part 47 CFR 15.225 as listed in the Grant of Equipment Authorisation and RSS-210 Annex B6 as listed in the Technical Acceptance Certificate.

The host product manufacturer is responsible for compliance to any other FCC and IC rules that apply to the host not covered by the modular transmitter Grant of Certification/ acceptance certificate.
2 Communication interface
2.1 Overview
The Reader can be controlled using a simple protocol available over SPI as described in Picture 1. The requirements are specified bt NXP for its CLRC663 IC.
This device is a RFID module that operates at 13.56 MHz with a maximum field strength of 64.666 dBuV/m @ 3m.
3 Compliance
A. The user and host equipment that incorporates this RFID reader module must follow all instructions listed in section 1 of this User Manual. B. Changes or modifications to this product not expressly approved by Wallbox could void the user’s authority to operate the equipment. C. This device complies with Part 15 of the FCC Rules. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif contient des émetteurs exemptés de licence qui sont conformes aux RSS(s) d’Innovation, Science et Développement économique Canada exemptés de licence. L’opération est soumise aux deux conditions suivantes : Cet appareil peut ne pas causer d’interférences. Cet appareil doit accepter toute interférence, y compris toute interférence qui peut causer le fonctionnement indésirable de l’appareil.
4 Marking and Labelling of the Product
1. The product shall contain as silkscreen printing the following information,
· The name Wallbox’. · The FCC ID “FCC: 2BB8L-RFID01” · The ISED number “IC: 31519-RFID01” 2. The Serial Number contained on the label affixed to the product shall be formatted as a nine-digit number directly printed on the board. 3. The product shall have affixed to it a Label containing the following including: ·V’ for manual visual inspection. · A’ for Automate Optical Inspection (AOI). ·F’ for functional testing and control. · `ICT’ for In-Circuit-Test applied to ensure the good quality of the design.

4. The label shall be placed as shown in below:

5 Installation Guide
This page indicates the installation guide for host manufacturers. This installation guide is addressed to expert technicians and it must not be available for end users.
Please use the official additional software and documentation in order to ensure the correct installation and use of this module.
Before installing the module ensure the following: – The product where module is to be installed must be compatible with WALLBOX RFID01. Update device in order to ensure that this module is fully compatible with the final product may be necessary. – The only necessary tools to install this product is a screwdriver. Additional tools can be useful to help in the process of install the module in final product.
1. Unpack the module and attach the supplied cables if necessary. 2. Dismount the final product and prepare it to assemble the module. 3. Ensure that there is enough space on the device to ease the installation and to avoid any non-
desired effect on the rest of electronics of the final device. 4. Install the module inside the host device and ensure that the position of the module is the final
one (module should be fixed on the host device to ensure a defined antenna location). 5. Connect the pins or cables following the below indication:

6. Take following considerations: – Make sure this device can fit within the final product without interference with any other
electronic. – Module should be installed with the cables provided if this connection is not available on your
product contact customer service for support. – WALLBOX RFID01 module must be powered by 3V3 dc supply. – Do not cover PCB antenna with conductive material.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 LIST OF APPLICABLE FCC RULES:
Compliance with §15.225 regulation
2.3 SPECIFIC OPERATIONAL USE CONDITIONS:
The module is typically use in industrial, household and general office / ITE and audio & video, EV charging system end-products. The product must not be co-located or operating in conjunction with any other antenna or transmitters.
2.4 TRACE ANTENNA DESIGNS:
The module was designed with the fixed PCB print antenna, any changes or modifications by the OEM integrator will require additional testing and evaluation.
Change in antenna type or maximum gain increase requires C2PC.
2.5 RF EXPOSURE CONSIDERATIONS:
The module has been evaluated and shown compliant with the FCC RF Exposure limits under fixed exposure conditions. OEM integrator shall equipped the antenna to compliance with antenna requirement part 15.203& 15.204 and must not be co-located or operating in conjunction with any other antenna or transmitters, otherwise, a Class II Permissive Change (C2PC) must be filed with the FCC must be applied.
RF exposure calculation has been provided with the module certification with worst case 20cm distance to users, RF exposure in the host equipment may need to be re-evaluated. Distance of 20cm shall be respected from module to users.
2.6 ANTENNAS:
The antenna of the module was deisgned as PCB printed on the PCBA board and the best gain is -3.90dBi. Modification the antenna design may need additional testing and evaluation.
Change in antenna type or maximum gain increase requires C2PC.
2.7 LABEL AND COMPLIANCE INFORMATION:
The final end product must be labelled in a visible area with the following “Contains FCC ID: 2BB8L-RFID01” or “Contains Module FCC ID: 2BB8L-RFID01” . If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users’ manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

A user’s manual for the finished product should include one of the following statements:
For a Class A digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
The User’s Manual for The finished product should include the following statements:
Any changes or modifications to this equipment not expressly approved by the OEM/Integrator may cause harmful interference and void the user’s authority to operate this equipment.
2.9 INFORMATION ON TEST MODES AND ADDITIONAL TESTING REQUIREMENTS:
Data transfer module demo board can control the EUT work in RF test mode at specified conditions. This radio module must not be installed to co-locate and operating simultaneously with other radios in the host system except in accordance with FCC multi-transmitter product procedures. Additional testing and equipment authorization may be required operate simultaneously with other radio.

2.10 ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER:
The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
General Statements
The module is intended only for OEM integrators.
The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed OEM integrator shall not modify and change the fixed designed PCB print antenna, and must not be co-located or operating in conjunction with any other antenna or transmitters, otherwise, a Class II Permissive Change (C2PC) must be filed with the FCC and/or a new FCC authorization must be applied.
The product is typically use in industrial, household and general office / ITE and audio & video, EV charging system end-products.
2.11 ADDITIONAL TESTING, ISED COMPLIANCE STATEMENT:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil contient des émetteurs/récepteurs sans licence qui sont conformes aux RSS sans licence d’Innovation, Sciences et Développement économique Canada. L’exploitation est soumise aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences. 2. Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer
un fonctionnement indésirable de l’appareil.
RF exposure compliant with a distance of equal or above of 20cm from EUT. Users must maintain a safety distance of 20cm with the device.

2.12 ISED MODULAR DISCLAMER:
The transmitter of this system is class B digital device that complies with Canadian ICES-003. Transmitter must not be located or operating in conjunction with any other.
The device is a module. When module is installed in host device, RF features may vary because of the installation. To be compliant with ISED host must ensure that Host products and associated modules (i.e. final product) shall meet all applicable requirements set out in RSS-Gen, including the radio frequency (RF) exposure compliance requirements in RSS-102.
The ISED certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labelled to display the ISED certification number for the module, preceded by the word “Contains” or similar wording expressing the same meaning, as follows: Contains IC: 31519-RFID01.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>