wallbox EIFFEL Mounting Pole Screwed Installation Guide

wallbox EIFFEL Mounting Pole Screwed

General Specifications

• Model: Eiffel
• Weight 30Kg
• Overall dimensions 1705.5 x 350 x 135mm
• Storage Temperature -40 ºC to 70 ºC
• Protection Rating IK10
• Material :
  • Structure: Galvanized + paint
  • Covers: SUS 430 + paint

Installation Instructions

• Ensure that the mounting surface can adequately support the weight of the pedestal and withstand mechanical forces associated with charger usage.
• Appropriate anti-collision protection must be provided by the customer when mounting the Eiffel pedestal in parking spaces.
• The calculation, design and manufacture of the concrete foundation lies in the scope of responsibility of the producer of the site.
• A horizontal, level and sound foundation is required for installation.
• The base must permit an adequate run-off for accumulated water.
• Do not mount the pedestal on asphalt. The stability of the pedestal on asphalt is not guaranteed. Wallbox recommends mounting the Eiffel pedestal on a concrete foundation.
• Install the pedestal in a sufficiently ventilated area. Do not install it in direct sunlight.
• Do not install your Wallbox pedestal near:
  • Flammable, explosive, or combustible materials.
  • Chemicals or Solvents.
  • Gas pipes or steam outlets.
  • Heat emitters such as radiators or batteries.
  • Areas prone to flooding, high humidity and running water.

Overview

1. The Mono Installation pedestal is designed for the installation of one charger.
2. The Dual installation pedestal is designed for the installation of two chargers. For dual installation of Eiffel, an extra mounting plate is required to be purchased separately.
3. Each Wallbox charger is compatible only with a specific model of Eiffel. Compatible chargers:

Tools and Mounting Parts

Required Tools

Included Mounting Parts

Notes

1. For dual installation of Eiffel, an extra charger adapter plate is needed. The extra charger plate is sold as a separate accessory.
2. You can purchase a rain protector plate as a separate accessory if you are planning to install the Eiffel pedestal outdoors. For dual installation, two rain protector plates will be required.
3. Rubber grommets and cabling tools are not included in the installation kit and should be purchased by the customer.

Mounting Base

1. Create a concrete foundation with an empty conduit and lay all the cables in the center of the foundation.
2. Ensure the cables have the appropriate excess length for the remaining installation.
3. Open the packaging and obtain the mounting parts needed for the installation.

Drilling

1. Make a hole in the center of base plate for the power supply cable.
2. Place the base plate on the top of the foundation, draw the power supply cable through the center hole and mark the positions of the four boreholes on the concrete foundation.
3. Remove the base plate and drill four holes
4. Remove the nuts and washers from the anchor bolts. Place the base plate on the foundation and align the four corner holes with the drilled holes.
5. Insert the anchors in the drilled holes and the base plate making sure that they are leveled and at least 40 mm above the top of the foundation.

Mounting

• Remove the pedestal from the packaging and then place the pedestal carefully over the four anchor screws.

• Place the washers and the nuts over the anchor screws and tighten the screws with the socket spanner extension. Tighten the iNDEX screws up to 34 Nm for Masonry and 54Nm for concrete.

• Install the charger according to instructions in its installation manual.
  For Dual installation, you will have to purchase a separate charger adapter plate and install the charger at the back panel of the pedestal.

• Fix the plug holder on the front panel by inserting the screws on the welded nuts.

Drilling Template

DISCLAIMER: Print the drilling template in scale 1:1 (format DIN A3)

Electric Connections

• Open the cover of the connection box and remove the thin plastic cover on required number of cable ports. Only one cable must be drawn through each grommet to ensure the IP protection.
  • You can purchase the Electric connections box and the front adapter plate separately
  • The electrical connection box can be adapted for up to 24 DIN rail mountings to enable dual installation if required.
• Remove the protective caps in the inside of the Electrical Box and center it with the four screws in the inside of the pedestal. 
• Fix the Electrical Box to the pedestal by inserting the four nuts on the screws. Ensure to place the protective caps back on the screws

Electric Wiring: Single Charger

Single Charger: Single Phase

Single Charger: Three Phase

Electric Wiring: Dual Chargers

Two Chargers: Single Phase

Two Chargers: Three Phase

Safety Recommendations

• Follow all the safety and installation instructions carefully. Failure to follow instructions may be a safety hazard and/or cause equipment malfunction.
• Any resulting damage due to disregard or actions contrary to the instructions in this manual is excluded from the product warranty.

Legal Notice

• Any information in this manual may be changed without prior notice and does not represent any obligation on the part of the manufacturer.
• Images in this manual are for illustration purposes only and might differ from the delivered product.

Safety and Maintenance Instructions

• Do not use this product if the enclosure is broken, cracked, open, or shows any other indication of damage. Please contact your distributor.
• The installation, maintenance, and servicing of the Eiffel pedestal must be performed only by qualified personnel in accordance with applicable local regulations. Unauthorized installation and modifications make the manufacturer warranty void.
• A minimum of two installers are required to perform the installation process for Wallbox Eiffel.
• Only Wallbox chargers should be installed on the pedestal.
• Wear Safety shoes, glasses and gloves as required by the local regulations during the installation.
• Protect your pedestal from any external impact.
• Do not use your pedestal under adverse climatic conditions.
• Do not open the door of the pedestal in rain.
• Take appropriate precautions with electronic medical implants.
• Disconnect main service power to the pedestal before cleaning the unit.
• Do not use cleaning solvents to clean any part of the charger or the pedestal. Clean it with a clean, dry cloth to remove dust and dirt accumulation.

Electrical Precautions

• The power supply line must be wired to an existing installation and must be in accordance to the local regulations.
• The pedestal must be permanently connected to the electrical Earth of the installation.

Limited warranty

• Wallbox warrants this product against defects in materials and workmanship for a period of 3 years from the date of purchase.
• During this period, at its discretion, Wallbox will either repair or replace any defective product at no charge to the owner.
• Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original warranty or six months whichever is greater.
• Any defect resulting from any accident, misuse, improper maintenance, or normal wear and tear is not covered by the limited warranty.
• Substitution or incorporation of any part by the client will be considered as incorrect usage.
• Except to the extent permitted by applicable law, the terms of this limited warranty do not exclude, restrict, or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Wallbox for instructions on where to send or bring it for repair.

Disposal Advice

In accordance to the directive 2012/19/EC, at the end of its useful life, the product should not be disposed of as urban waste. It should be taken to a collection center or a distributor that provides disposal of special and differentiated waste.

References

• Home - Wallbox Help Center
• Home - Wallbox Help Center

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>