wallbox B034A Pedestal Eiffel Installation Guide

Table of Contents

wallbox-B034A-Pedestal-Eiffel-product-image

A. Ensure that the mounting surface can adequately support the weight of the pedestal and withstand mechanical forces associated with charger usage.
B. Appropriate anti-collision protection must be provided by the customer when mounting the Eiffel pedestal in parking spaces.
C. The calculation, design and manufacture of the concrete foundation lies in the scope of responsibility of the producer of the site.
A horizontal, level and sound foundation is required for installation.
E. The base must permit the adequate run-off for accumulated water.
F. Do not mount the pedestal on asphalt. The stability of the pedestal on asphalt is not guaranteed.
Wallbox recommends mounting the Eiffel pedestal on a concrete foundation.
G. Install the pedestal in a sufficiently ventilated area. Do not install it in direct sunlight.
Do not install your Wallbox pedestal near:
- Flammable, explosive, or combustible materials.
- Chemicals or solvents.
- Gas pipes or steam outlets.
- Heat emitters such as radiators battery
- Areas prone to flooding, high humidity and running water.

The Mono Installation pedestal is designed for the installation of one charger.
The Dual installation pedestal is designed for the installation of two chargers.
For dual installation of Eiffel, an extra mounting plate is required to be purchased separately.
Each Wallbox charger is compatible only with a specific model of Eiffel. Compatible chargers:

Required tools

wallbox-B034A-Pedestal-Eiffel-01

Included Mounting Parts

Notes

wallbox-B034A-Pedestal-Eiffel-03

For dual installation of Eiffel, an extra charger adapter plate is needed. The extra charger plate is sold as a separate accessory.
You can purchase a rain cover plate as a separate accessory if you are planning to install the Eiffel pedestal outdoors. For dual installation, two rain covers plates will be required.
Rubber grommets and cabling tools are not included in the installation kit and should be purchased by the customer.

wallbox-B034A-Pedestal-Eiffel-04

Build a concrete foundation with an empty conduit and lay all the cables in the center of the foundation.
Ensure the cables have appropriate excess length for the remaining installation.
Open the packaging and obtain the mounting parts needed for the installation.

Place the drilling template on the top of the foundation, pass the power supply cable through the center hole and mark the positions of the four boreholes on the concrete foundation.
Remove the drilling template and drill four holes.
Remove the nuts and washers from the anchor bolts.
Insert the anchors in the drilled holes making sure that they are leveled and at least 40mm above the top of the foundation.

Remove the pedestal from the packaging and then place the pedestal carefully over the four anchor screws.
Place the washers and the nuts over the anchor screws and tighten the screws with the socket spanner extension.
Tighten the iNDEX screws up to 34 Nm for Masonry and 54Nm for concrete.
Install the charger according to instructions in its installation manual.
For Dual installation, you will have to purchase a separate charger adapter plate and install the charger at the back panel of the pedestal.
Fix the plug holder on the front panel by inserting the screws on the threaded holes.

wallbox-B034A-Pedestal-Eiffel-10

Open the cover of the connection box and remove the thin plastic cover on required number of cable ports. Only one cable must be drawn through each grommet to ensure the IP protection.
- You can purchase the electric connections box and the front adapter plate separately.
- The electrical connection box can be adapted for up to 24 DIN rail mountings to enable dual installation if required.
Remove the protective caps in the inside of the Electrical Box and center it with the four screws in the inside of the pedestal.
Fix the Electrical Box to the pedestal by inserting the four nuts on the screws. Ensure to place the protective caps back on the screws.

Safety Recommendations

Follow all the safety and installation instructions carefully. Failure to follow instructions may be a safety hazard and/or cause equipment malfunction.
Any resulting damage due to disregard or actions contrary to the instructions in this manual is excluded from the product warranty.

Legal Notice

Any information in this manual may be changed without prior notice and does not represent any obligation on the part of the manufacturer.
Images in this manual are for illustration purposes only and might differ from the delivered product.

Safety and Maintenance Instructions

Do not use this product if the enclosure is broken, cracked, open, or shows any other indication of damage. Please contact your distributor.
The installation, maintenance, and servicing of the Eiffel pedestal must performed only by qualified personnel in accordance with applicable local regulations. Unauthorized installation and modifications make the manufacturer warranty void.
A minimum of two installers are required to perform the installation process for Wallbox Eiffel.
Only Wallbox chargers should be installed on the pedestal.
Wear Safety shoes, glasses and gloves as required by the local regulations during the installation.
Protect your pedestal from any external impact.
Do not use your pedestal under adverse climatic conditions.
Do not open the door of the pedestal in rain.
Take appropriate precautions with electronic medical implants.
Disconnect main service power to the pedestal before cleaning the unit.
Do not use cleaning solvents to clean any part of the charger or the pedestal. Clean it with a clean, dry cloth to remove dust and dirt accumulation.