Kyvol TL-L30 Robot Vacuum User Manual

June 1, 2024
KYVOL

TL-L30 Robot Vacuum

“`html

Product Information

Specifications

  • Model: TL-L30 Robot Vacuum

  • Main Features: Collision sensor, cliff sensor, universal wheel,
    2-in-1 water tank

  • Accessories: Main unit, charging dock, mop bracket, cleaning
    brush

Product Usage Instructions

Safety Instructions

It is important to follow these safety instructions:

  • Read the user manual carefully before using the product.
  • Only dismantle the lithium-ion battery by professionals for
    proper disposal.

Battery and Charging

Instructions for battery and charging:

  • To disassemble the battery, follow these steps when abandoning
    the robot vacuum cleaner.

  • Ensure the robot vacuum cleaner is turned off before removing
    the battery pack.

  • Consult professionals for battery recycling.

Product Maintenance

Regular maintenance is essential for optimal performance:

  • Clean the dust box and water tank regularly.
  • Replace the mop and cleaning brush as needed.

FAQ

Common Problems

Refer to the troubleshooting section in the user manual for
common problems and solutions.

FCC Warning

Ensure compliance with FCC regulations for device operation.

Troubleshooting

If you encounter issues with the robot vacuum, consult the
troubleshooting guide in the user manual for assistance.

“`

TL-L30 Rob ot V acuum
User Manual
Please read this manual carefully before using the product and keep it properly.

Contents

Safety instruction

01

Common Problems

13

Product Introduction

03

Troubleshooting

14

Production Installation

06

Basic parameters

15

Product Use

08

FCC WARNING

15

Product Maintenance

09

Safety instruction

Use instructions
· This product is only used for floor cleaning in home environment, and should not be used in outdoor, non-floor, commercial or industrial environment. · This product may not be used by people with physical, sensory or intellectual disabilities and people without relevant experience and knowledge (including children), unless there is a guardian’s care or guidance to ensure that they can use this product safely. · Do not let children use the robot vacuum cleaner as a toy. When the robot vacuum cleaner works, please supervise children and pets to keep them away as far as possible. · If the charging dock is damaged, it must be replaced with special components purchased from its manufacturer or maintenance department. · Do not place children or pets and anything on the stationary or running robot vacuum cleaner. · Do not place the cleaning brush in the area where children can touch it. · Do not use it in suspended environments (such as duplex floors, open balconies and furniture tops) without protective fences. · Do not use it in an environment where the temperature is higher than 35, lower than 0 or there are any liquids and sticky objects on the ground. · Do not use it to clean any burning objects. · Before use, please put away the wires on the floor of your home to avoid dragging when the robot vacuum cleaner is running. · Please put away the fragile items, valuables and sundries (such as vases, plastic bags and mirrors, etc.) on the ground to avoid the damage of household items caused by the obstruction or slight collision of the main unit during operation.

· Do not let the robot vacuum cleaner suck hard objects or sharp objects (such as decoration waste, glass and nails, etc.). · Do not use mopping mode on the carpet. · Please clean and maintain the robot vacuum cleaner and charging dock in the power-off state. · Do not turn the robot vacuum cleaner upside down on the ground for a long time. · Do not wipe with wet cloth or wash the main unit and charging dock with any liquid. · Please use this product according to the instructions in the manual or quick guide. Any loss caused by improper use shall be borne by the user. · If it is needed to transport products, please ensure that the robot vacuum cleaner is turned off, and it is recommended to use the original packaging box for packaging protection. · This product’s laser radar meets the IEC 60825-1:2014 Standard for Class 1 laser product safety and does not produce laser radiation hazardous to the human body.
01

Safety instruction
Battery and charging
· Do not use any third-party battery, charging dock or power adapter. · Do not disassemble, repair or modify the battery or charging dock without permission. · Do not place the charging dock near the heat source (such as radiator, etc.). · Before scrapping this product, you must disconnect the power supply and take the battery out of the machine for environmental protection. · If it is not used for a long time, please turn off the robot vacuum cleaner after being fully charged and put it in a cool and dry place. It is recommended to charge at least once every three months to avoid battery damage.

Instructions on environmental protection
The chemical substances contained in the built-in lithium-ion battery of this product will pollute the environment. Please dismantle it by professionals before scrapping it, and hand it over to a professional battery recycling agency for centralized disposal.
Steps to disassemble the battery The following information is only applicable when the robot vacuum cleaner is abandoned, not the daily operation instructions: 1. Let the robot vacuum cleaner run until it can’t be cleaned with low power without touching the charging dock; 2. Turn off the robot vacuum cleaner; 3. Remove the screws of the battery pack of the robot vacuum cleaner; 4. Take out the battery pack and press the fastener to pull out the connector plug of the battery pack.

02

Product Introduction

List of accessories

2-in-1 water tank

Main brush Rubber brush Main brush cover Filter screen ×2

Main unit
Note: The illustrations of products, accessories and user interface in the manual are schematic diagrams for reference only. Due to the product updating and upgrading, there may be some differences between the physical products and the schematic drawings. Please take the physical products as the standard.

Charging dock

Mop bracket

Mop×2

Side brush×2

Cleaning brush

330L Robot Vacuum Cleaner User Manual
Please read this manual carefully before using the product, and keep it properly.
User Manual

03

Quick Guide

Product Introduction

Main unit
Collision sensor
On-off button Recharging button Laser

Cliff sensor
Universal wheel
Battery pack Side brush
Main brush Main brush cover Left wheel/Right wheel
Mop bracket

Charging electrodes

On-off button

Recharging button

Press for a long period of time, powering-on or powering-off Press for a short period of time, cleaning or pausing

In operation, press for short time, main unit pauses In pausing, press for short time, start recharging In recharging, press for short time, stop recharging Press and hold for 5s to restore factory settings

+ , press for 3s to reset Wi-Fi to enter network configuration

2-in-1 water tank

Description of button indicator status of the main unit

White light is always on

Power-on is completed / normal work / charging is completed / standby

White light flashes

In recharging / connecting to the network / upgrading

White light breaths

In charging / powering-on

Yellow light is always on Not networking

Yellow light flashes

Reset Wi-Fi / abnormal state

Yellow light breaths

Charge when the power is lower than 20%

Light distinguishes

in sleeping

04

Product Introduction
2-in-1 water tank
Rubber cover Water injector Dust box Water tank Fastener
Mop bracket
Mop
Mop bracket

Charging dock (against the wall)
Power adapter Charging shrapnel
05

Production Installation
1. Place the charging dock against a wall, and connect the power supply

0.5m

Tips:

1.5m

0.5m

· Do not expose the charging dock to direct sunlight.

· Make sure there is more than 1.5m space in front of the charging dock and more

than 0.5m space on both sides.

· Pay attention to the power cord, otherwise it may be dragged by the robot,

causing the charging dock to move or power off.

2. Remove the anti-collision protection strip and protective film
Before use, be sure to remove the anti-collision protection strips on both sides of the main machine.

3. Power on and charging
At initial use, long press ” ” button for 3 seconds to power on, and manually place the main unit onto the charging dock by aligning the pole piece with the charging electrode. In daily use, you can start intelligent recharging by directly pressing ” ” button.
Tips: · When main unit fails to power on due to low battery level, place it on charging dock for charging. · The main unit will start up automatically after connected to the charging dock, and cannot be shut down during charging.

06

Production Installation
Installation of 2-in-1 water tank and mop bracket
1. Take out the 2-in-1 water tank, open the rubber cover of the 2-in-1 water tank, inject clean water into the water tank and fasten the rubber cover; soaking and water injection are forbidden.

3. Align the positioning hole and install the mop bracket into the bottom of the 2-in-1 water tank according to the direction shown in the figure.

4. Install the 2-in-1 water tank into the main unit according to the direction shown in the figure, and confirm that the fastener is installed in place.

2. Put the wrung wet mop into the mop bracket and stick it on the hook and loop.

Tips: · Do not inject hot water into the 2-in-1 water tank to avoid deformation of the water tank. · It is forbidden to shower or soak the 2-in-1 water tank! It is forbidden to use cleaning products such as detergent, disinfectant and solid detergent to avoid corrosion and blockage of the 2-in-1 water tank. · When injecting water, take out the 2-in-1 water tank separately, only clean water can be used, and the small water flow at the water injection port can be injected into the water tank. · When using the mopping function, soak the mop cloth first, wring it until it doesn’t drip, and then install it on the mop bracket for use; after mopping the floor, please take out the 2-in-1 water tank and mop bracket in time, and pour out the remaining water in the water tank. · Do not use the mopping function when no one is at home. · Because of production inspection, there may be a small amount of water in the 2-in-1 water tank, which is a normal phenomenon.
07

Product Use

Power-On/Off
Press” “for 3s, indicator light is on and the main unit is on. When the main unit is not charged and paused, press” “for 3s to make it power-off.
Vacuumming/Mopping
In the powered-on state, press the” “button for short and the main unit will automatically enter the vacuumming/mopping state according to the installed accessories.
Pause
When main unit is in operation, press any button to cease operation; Press button” “to continue sweeping; Press button” “to return it to charging dock for charging and finish current sweeping task.
Sleep
Unless during charging, the main unit will go to sleep automatically when it is left idle for 5 minutes, and power off automatically when it has slept for 6 hours. In sleep status, press any button will wake main unit up. Tips: Main unit will not go to sleep when charging on the charging dock.
Equipment recharge
In the power-on state, press the ” ” button for short, and the main unit will enter the recharging mode; when the main unit is cleaned, it automatically enters the recharging mode, and the white indicator light flashes; when the power level of the main unit is too low during cleaning, it will recharge automatically.

Add water or clean mop to the 2-in-1 water tank halfway
If it is needed to add water or clean the mop during the cleaning process of the main unit, press any button for short to pause, then remove the 2-in-1 water tank to add water or clean the mop, and then put it back into the water tank and mop, and press the ” ” button for short to continue working.
Reset Wi-Fi
When the main unit is turned on, press and hold the” “+” ” buttons for 3s until you hear a sound prompt, and when the indicator is in a yellow flashing state, it means that the WiFi reset is successful. Equipment network distribution: open the APP to add equipment, and follow the APP prompts. Tips: Only Wi-Fi network in 2.4GHz frequency is available to this product.
Global cleaning
Start the global cleaning through the APP or short press the” ” buttons. The main unit will first use the” bow ” shape clean the whole house along the way, then clean along the edge, and automatically recharge after the edge cleaning.
Edge Cleaning
Select edge cleaning in APP. After the main unit automatically identifies the cleaning area, it will be cleaned along the edge. After the cleaning, the main unit will automatically return to the charging dock.
Zone cleaning
Set the zone cleaning in the APP, the host will clean the zoned area with the machine, and automatically recharge after the cleaning is completed.
08

Product Use

Fixed-point cleaning
Select where to scan in the APP, and then set the target point on the map. The main unit will automatically plan the route to the target point. The target point is the center, and the cleaning is carried out in a square area of 2m × 2m. It will automatically recharge after cleaning is completed. The default suction gear is strong gear, and the suction can be switched.
Scheduled cleaning
User can schedule a cleaning task in App, and main unit will start the cleaning task as scheduled and return to charging dock upon end of the task. Tip: If the Do Not Disturb mode is turned on, scheduled cleaning will not be performed during the Do Not Disturb time period.
Virtual Wall/Restricted Area
A virtual wall/restricted area can be set in the APP to prohibit the main unit from entering the area that does not need to be cleaned. Tip: · Before using this function, you need to save the map in the APP. · Moving the main unit or aggravating the obvious changes in the environment may cause the original map to fail and the virtual wall/restricted area to be lost.
Do Not Disturb Mode
During the Do Not Disturb time period, the main unit will not respond to breakpoints to continue scanning, schedule cleaning, or actively broadcast voices. Do not disturb mode is enabled by default, and the default time period is from 23:00 to 9:00. You can turn Do Not Disturb on/off within Do Not Disturb, or set a time period. Tip: During the Do Not Disturb time period, the indicator light will turn off after the main unit is charged for 1 minute.

Continue to scan
During the cleaning process, it will automatically recharge when the battery is low. After charging, it will automatically return to the interruption point to continue cleaning. If you manually end the cleaning, move or operate the main unit during the recharging or charging process, this breakpoint continuous cleaning will be canceled.
Suction adjustment
The cleaning suction of the main unit can be set through the APP, and the default is the standard gear.
Robot searching
The robot searching can be set through the APP, and the location of the main unit can be found through the sound of the robot vacuum cleaner.
Volume adjustment
The volume of the robot vacuum cleaner can be controlled and adjusted by APP, and the volume can be adjusted to 0, 10%, 20%, 30%…100%.
Firmware upgrade
The APP can control the device to upgrade the firmware; During the upgrade process, when the main unit is on the charging dock or the power is greater than 30%, it is not allowed to start cleaning during the upgrade.
09

Product Maintenance
Cleaning of 2-in-1 water tank
1. Press the fastener on the left and right sides of the 2-in-1 water tank inward and pull it out horizontally from the main unit.

3. Open the rubber cover of the 2-in-1 water tank and pour out the remaining water in the water tank.

Fastener
2. Open the dust box cover of the 2-in-1 water tank, pour out the garbage inside and clean the dust box with a cleaning brush.

4. Install the 2-in-1 water tank back to the main unit.

Tips: After mopping the floor, please take out the water tank in time, pour out the remaining water in the water tank in time, clean the mop and dry it to avoid odor and mildew.
10

Product Maintenance
Mop bracket
Hold both sides of the mop bracket by hand, and vertically pull out the bottom of the 2-in-1 water tank according to the direction shown in the figure.
Filter screen
Open the dust box cover of the 2-in-1 water tank as shown in the figure, then press the buckle to pull out the filter and clean it.

Main brush
1. Turn over the main unit, lift the fastener and remove the main brush cover. 2. Take out the main brush upward. 3. Cut the hair wound on the main brush with a knife on the cleaning brush and clean the main brush. 4. Install the main brush back and press the fixing fastener of the main brush cover.
Main brush cover Fastener
Main brush
Cleaning method of main brush

Tips: · After washing the filter screen, please be sure to dry it before using it. · In order to avoid blockage of the filter screen, it is recommended to clean the filter screen regularly. · It is recommended to replace the filter screen every 3 months.

Cut hair

Clean up dirt

Tips: It is recommended to replace the main brush every 6-12 months to ensure the cleaning effect.

11

Product Maintenance
Cleaning method of rubber brush
Side brush
1. Turn over the main unit and remove the side brush fixing screw. 2. Remove and clean the side brush. 3. Replace the side brush and lock the screws.

Sensor
Please use a soft dry cloth to clean the cliff sensor regularly. Cliff sensor
Tips: Do not use chemicals such as detergent or spray to clean the sensor.

Tips: It is recommended to replace the side brush every 3-6 months to ensure the cleaning effect.
12

Common Problems

Problem
Unable to power on
Unable to charge
The main unit cannot return to charge The main unit behavior is abnormal The main unit is offline The main unit cannot connect to Wi-Fi Abnormal sound during cleaning
Cleaning capacity is declined
Fail to do scheduled cleaning
Unable to continue scanning
Whether it is needed to cut off the power supply of the charging dock and turn it off when charging is completed

Solution
The battery is low and please charge it before using it.
The charging dock is not powered on and please make sure the power connection is successful. The contact of the charging electrode is poor and please clean the charging shrapnel of the charging dock and the charging pole piece of the main unit. The ambient temperature is too low(below 0) or too high(above 35).
Please make sure there is enough space around the charging dock. Please ensure that the identification area on the surface of the charging dock is free from dust and dirt. The charging dock is not powered on. Please power on the charging dock before using it.
Please turn it off and turn it on again.
Please make sure that the main unit is successfully connected to the network, and that the main unit is always in the range of Wi-Fi signal.
Please make sure that the main unit and the charging dock are within the range of Wi-Fi signal, and the signal is good. Please try resetting Wi-Fi before pairing.
The main brush, the side brush, the left/right wheel or the universal wheel may be entangled with foreign matters. Please power it off and clean it up.
The dust box is full, please clean it. The filter screen is blocked, please clean it. The main brush is entangled by foreign matter, please clean the main brush.
Please make sure that the main unit is not in Do Not Disturb mode. Scheduled cleaning cannot be performed in this mode. Please confirm that the main unit is connected to the network. If the main unit is not connected to the network, the time cannot be synchronized, and the scheduled cleaning will not start.
Please make sure that the host is not in Do Not Disturb mode, it will not continue to scan in this mode. Operating the APP to recharge, short pressing the recharge button, or transporting the host back to the dust collection station will not continue to sweep.
During daily use, the standby power consumption is extremely low, and there is no need to turn off the power. Keeping the charging state is conducive to the best performance of the battery. If it is not used for a long time, please cut off the power supply of the charging dock and power it off for storage. It is recommended to charge the battery once every 3 months to prevent the battery from being damaged due to over-discharge.
13

Troubleshooting

Fault Message
Please confirm that the laser ranging sensor is not blocked and then start
Clean cliff sensor and relocate robot
Check collision sensor and remove any foreign object on it
Place robot on a horizontal ground and start it
Remove any obstacle around robot and try again
Place confirm that the 2-in-1 water tank has been installed in place
Make sure the mop is installed
Please put the main unit back into the charging dock
Low battery level. Please charge robot
In case the driving wheel is abnormal, please check and clean the driving wheel
In case the side brush is abnormal, please check and clean the side brushing
In case the main brush is abnormal, please check and clean the main brush

Solution
The laser ranging sensor is blocked or stuck by foreign objects, please remove the blocking objects or foreign objects; if it cannot be removed, please move the host to a new location to start. Robot is off ground. Relocate and restart robot. Cliff sensor is dirty. Clean the sensor. Collision sensor is jammed. Remove foreign object by tapping the sensor. If there is no foreign object, relocate and restart robot. When starting, the tilt of the main unit is detected. Please put the main unit on the level ground and restart. The wheel is suspended, please move to a new position to start. Robot may be jammed or trapped. Remove any barrier around it. Please install the 2-in-1 water tank back and confirm that the 2-in-1 water tank has been installed in place. Replace the mop and make sure the mop bracket is in place. In case recharging is failed, the main unit can’t sense the position of the charging dock. Please put the main unit back to the charging dock. The power is too low, so the main unit can’t start normally. Please put the main unit back in charging dock for charging.
The driving wheel may be entangled with foreign matter, please power it off and clean it up.
The side brush may be entangled with foreign matter, please power it off and clean it up.
The main brush may be entangled with foreign matter, please power it off and clean it up.
14

Basic parameters

Main unit
Product Name Model Size Rated Power Rated Voltage Voltage
Battery capacity
Net weight Wireless Connection

Robot Vacuum TL-L30 325×325×97mm 40W 14.4V 20V 2600mAh (nominal capacity), 2500mAh (rated capacity)
2.8kg Wi-Fi IEEE 802.11b/g/n 2.4GHz

Charging Dock

Model Dimensions Rated input Rated outpu

GDZTL-L1 150×128×84mm 20V 0.6A 20V 0.6A

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
15

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals