Kyvol EA200 Ultrasonic Cool Mist Humidifier User Manual

Kyvol EA200 Ultrasonic Cool Mist Humidifier

Important Safety Instructions

Please read these IMPORTANT SAFETY INSTRUCTIONS before using EA200(WIFI). You may avoid some issues during use of the product by doing so but following the instructions completely to operate the humidifier is not a must.

Before Using the Humidifier

• Check the Power Cord for any signs of damage. If yes, please do not use the humidifier.
• DO NOT place the humidifier in a wet environment.
• Please always keep the humidifier out of the reach of patients, child ren, and pets.
• Please always place the humidifier on a smooth, flat, lint-free, non-metallic, waterproof, and level surface; avoid the direct sunlight.
• Always place the humidifier ≥ 2 feet (60 cm) above the floor, and ≥ 12 inches (30 cm) away from the wall, other appliances, or wooden furniture.
• DO NOT place the humidifier on a carpet, towel, or wood surface; otherwise, it will stove, block the vent and may damage the product.
• DO NOT place the humidifier near open flames and heat sources, such as flames and heat sources, such as

When Using the Humidifier

• DO NOT plug the power cord into an outlet with wet hands.
• DO NOT plug the power cord into an outlet with wet hands.
• DO NOT cover the Nozzle with your hand or any other objects when the humidifier is on to avoid damage to the product or injury.
• DO NOT move or tilt the humidifier during operation.
• DO NOT clean the humidifier when it is connected to a power source or when it is turned on.
• The recommended comfortable environment humidity is between 40% – 60%. Please adjust the mist as needed

After Using the Humidifier

• Always disconnect the power supply by unplugging it when the humidifier is not in use.
• The humidifier requires regular cleaning. Please refer to the instructions mentioned in the section of Maintenance and Care.
• DO NOT clean the humidifier immediately after turning it off. Allow the humidifier to cool down completely before cleaning.
• DO NOT attempt to repair or adjust any electrical/mechanical functions of the humidifier by yourself.

Packing List

•  Humidifier EA200(WI FI) X1
•  Cleaning Brush X1
•  Dustproof Sponge X1
•  User Manual X1

Specifications

Product Overview

Operating Guide

Add Water

1.  Remove the Nozzle first, separate the Water Tank from the Base, turn the Water Tank upside down, loosen the Tank Cap, then fill the tank with clean cool water.
2.  Tighten the Tank Cap, put the Water Tank upright and back on the Base.

Important

•  If the tap water is too hard, we recommend using the filtered or distilled water to avoid white dust. DO NOT use hot water.
•  DO NOT add any essential oils or medicinal tablets into the Water Tank.
•  DO NOT add water into the Base or through Nozzle.
•  DO NOT move the humidifier while the Water Tank is full of water to avoid leakage or Base overfilling.

Power ON / OFF and Mist Adjustment

1.  Plug the Power Cord into a socket.
2.  Rotate the Control Knob clockwise to ON/MIN to turn on the humidifier. The Water Indicator will turn solid green and the is at the minimum level.
3.  Continue rotating the Control Knob clockwise from ON/MIN to MAX to Level steplessly increase the intensity of mist.
4. Rotate the Control Knob counterclockwise from MAX to ON/MIN to reduce the intensity of mist.
5.  Rotate the Control Knob counterclockwise to OFF to turn off the humidifier, and the Water Level Indicator will be off.

Low Water Protection
When there is not enough water in the Water Reservoir, the Water Level Indicator will turn red. The humidifier stops misting to prevent it from overheating and damaging the Atomizer

Operating Via Kyvol App

This operation is available for AF600 (with Wi-Fi) ONLY.

App Downloading and Installation
Option 1:
Search for Kyvol from App StoreTM,/Google PIayTM ,then download and install it on your mobile device.
Note:
Google PlayTM is a trademark of Google Inc., and App StoreTM is a trademark of Apple Inc.
Option 2:
Scan the QR codes below to download and install.

App Registration and Login
Launch Kyvol APP, register an account with your mobile phone number or a valid email address at your first use, then log in.
Note:
For a successful connection, please allow Kyvol APP to use your WLAN & Cellular Data when running it.

Connection Mode

Important
For the humidifier:
Make sure the humidifier has been plugged into a socket.

For Wi-Fi network:

1.  Before connecting, please turn on location service/GPS on your phone and grant all the permissions required by Kyvol App.
2.  Make sure your mobile device is connected to a 2.4GHz Wi-Fi.
3.  Make sure you’ve entered the correct Wi-Fi name and password when connecting.
4.  Make sure the humidifier, your mobile phone and your router are close enough when connecting.

Bluetooth Mode

•  Connect the power cord of the humidifier to a socket.

•  Launch Kyvol App, and tap Add Device.

•  Tap Humidifier, then select the model.

•  Tap Next on the Bluetooth Mode page.

•  Turn on the Bluetooth and Location access on your mobile device

•  Quickly rotate the Control Knob from OFF to ON, then from ON to OFF three times. The WiFi Status
  Indicator will keep flashing red, which means the humidifier is ready for network connection.

•  Tap Search.

•  Select the device model and tap Connect.

•  Select WiFi and enter the correct password; tap Confirm.

•  Connecting.

•  Connected. The WiFi Status Indicator will turn solid.

Wi-Fi Mode

•  Connect the power cord of the humidifier to a socket.

•  Launch Kyvol App, and tap Add Device.

•  Tap Humidifier, then select the model.

•  Turn on the Location access on your mobile device. Tap Wi-Fi Mode, then tap Next.

•  Quickly rotate the Control Knob from OFF to ON, then from ON to OFF three times. The Wi-Fi Status
  indicator will keep flashing red, which means the humidifier is ready for network connection.

•  Select Wi-Fi and enter the correct password; tap Confirm.

•  Connecting.

•  Connected. The Wi-Fi Status Indicator will turn solid on.

Power ON / OFF
Step 1:
Launch Kyvol App.

Step 2:
Select Power On/Off.

Mist Adjustment
Step 1:
Launch Kyvol App.

Step 2:
Select Mist Level

Maintenance and Care

Important

•  DO NOT submerge the Base in the water.
•  Make sure the water does not enter the Base through the Air Outlet, Air Inlet or Control Knob.
•  DO NOT wash any part of this humidifier in the dishwasher; otherwise, it will damage the humidifier.

Daily Maintenance

Step 1:
Turn off the humidifier and unplug the Power Cord from the socket.
Step 2:
Drain water from the Water Tank, Water Reservoir, and Base.

Weekly Maintenance

1.  To property clean your humidifier, we recommend that you remove scale and disinfect the humidifier separately.
2.  DO NOT mix vinegar and bleach solution together. To avoid damage to the humidifier, do not use more than 1 teaspoon of bleach per gallon of water.
3. Please make sure the white sealing ring on the Tank Cap is installed correctly after cleaning to avoid water leakage.

Scale Removal Instructions
Step 1:
Turn off and unplug the humidifier.
Step 2:

1.  Separate the Water Tank from the Base, then remove the Tank Cap. Make sure that the white Sealing ring does not come off.
2.  Drain water from the Water Tank and Base, then remove all accessories and set aside.

Step 3:

1.  Fill the Water Tank halfway.
2.  Add in 1 teaspoon of undiluted distilled white vinegar.
3.  Attach the Tank Cap and shake for 15 seconds.

Step 4:

1.  Place the Water Tank back to the Base.
2.  The vinegar solution will enter the Water Reservoir to loosen mineral scale on the Atomizer, Water Floater, and the bottom of the Water Tank. Leave it for 15-20minutes.

Step 5:

1.  Uncap the Tank Cap and drain the solution.
2.  Wipe the Atomizer and floater with a soft cloth to remove loose mineral deposits.

Step 6:
Flush both the Water Reservoir and Water Tank until the smell of vinegar ( for scale removal) or bleach solution (for disinfection, see below) is gone .

Disinfection Instructions

Step 1:
Follow steps 1 to 2 in the previous section for scale removal.

Step 2:

1.  Fill the Water Tank halfway.
2.  Add ‘/2 teaspoon of bleach.
3.  Attach the Tank Cap and shake for 15 seconds.
4.  Place the Water Tank back to the Base. The bleach solution will enter and disinfect the Water Reservoir and the other components. Leave it for 15-20 minutes.

Step 3:
Follow steps 4 to 6 of the previous section for scale removal to complete the disinfection of the humidifier.

Dustproof Sponge Cleaning

Clean the Dustproof Sponge (located at the bottom of Base) with water or detergent once a month, then put it back in place after cleaning.

End-Of-Season Care and Storage

1.  Follow the cleaning instructions when the humidifier will not be used for at least one week, or at the end of the season. Remove all accessories used in the humidifier. Allow the humidifier and accessories to dry completely before storing it.
2.  DO NOT store water in the Base, Water Reservoir or Water Tank.
3.  Pack the humidifier safely and store it in a cool, dry place.

Troubleshooting Guide

•  If you need any further assistance, please feel free to contact us at support@kyvol.com.
•  Failure to keep the humidifier clean and free of mineral deposits may affect the operation of it.
  Issue| Possible Cause| Solution
  ---|---|---
  | The humidifier is not plugged in.| Make sure the humidifier is properly plugged into a

socket.

The Water Level

lndicator is off.

| No power from the outlet| Try to use other power

outlets.

| The humidifier is not turned on.| Check if the Control Knob is turned to ON/MIN.
| No water in the Water Reservoir.| Make Sure the 1. Spring is fixed correctly to the bottom of the tank so that water can pass through to

the Base.

The Water Level lndicator stays red.

|
| 3. Water Floater was Stuck| Adjust the 3. Water Floater to a horizontal position and make sure it can rise

with water

| Not enough water inside the

tank

| Refill and re-install the

water Tank.

---|---|---
The Water Level| Mist Level is set too low.| Adjust the humidifier to
indicator is green but| | the maximum mist.
there is no or little| Mineral build-up on the| Check if any air comes out
mist produced.| Atomizer.| from the Nozzle. If not,
| | then clean water scale on
| | the atomizer as instructed.
| The Base might be overfilled.| Remove the tank, empty
| | the Base, then place the
| | filled tank on the empty
| | Base.
| Tank may be damaged.| Check for possible cracks
| | in tank. If yes, please
| | replace it.
| Tank Cap is not tightened| Tighten the tank Cap.
| securely.|
| 1. Spring was stuck.| Make sure the 1. Spring is
Tank Leakage| | fixed correctly to the
| | bottom of the tank so that
| | water can pass through to
| | the Base.
| 2. Sealing Ring was not installed| Make sure the 2. Sealing
| on tank Cap.| Ring has been installed on
| | the Tank Cap. Please
| | contact us if it is lost.
The mist makes the| Mist level is set too high for the| 1. Check if the room is too
surrounding tables| room size.| humid and adjust the
or floors damp.| | humidifier to a lower mist.
Condensation occurs| | 40%-60% works best.
around humidifier or| | 2. Open door and windows
on windows/walls.| | or change to a larger room.
| Air Inlet was blocked.| Make sure the humidifier is
| | placed on a hard flat
The mist makes the| | surface of >2 feet above
surrounding tables| | the floor and >12 inches
or floors damp.| | away from the wall. Make
Condensation occurs| | sure the Nozzle is not
around humidifier or| | facing the wall or window.
on windows/walls.| Low indoor temperature leads to| Adjust the room
| liquefaction| temperature to 25°C /
| | 77°F.
The humidification is| Mist level is set too low for the| 1. Adjust the humidifier to
too poor.| room size| the maximum mist. 2.
| | Close door or windows to
| | reduce air ventilation or

change to a smaller room.

---|---|---
| Air Inlet was blocked.| Make sure the humidifier is placed on a hard flat surface of >2 feet above the floor and >12 inches away from the wall. Make sure the Nozzle is not

facing the wall or window.

| Low indoor temperature leads to liquefaction| Adjust the room temperature to 25°C /

77°F.

White dust appears or the black coating on the Base flakes

off.

| The tap water may contain too many minerals.| Please replace it with filtered or distilled water.
Strange odour| Please clean the humidifier.| 1.   Please make sure to clean the humidifier according to the instructions.

2.   Leave the empty Water Tank in a cool place for 12 hours without covering

Tank Cap.

Strange water noise| Water is going down to the

Water Reservoir.

| This is normal while it is

working.

Humidifier is getting too hot.| The humidifier worked for too long| Please power it off and put it in a well-ventilated place

for 10 minutes.

Customer Service

For FAQs and troubleshooting advice, please contact us via:
E-mail:
support@kyvol.com (North America)
support.uk@kyvoI.com (United Kingdom)
Live Chat: www.kyvol.com
Facebook: @kyvolglobal
Instagram: @kyvol_global
Kyvol is happy to be of service.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

•  Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation and service of the product.
•  Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g. during transport, cleaning by inappropriate means, etc.).
•  Natural wear and aging of consumables or components during use (such as batteries, etc.).
•  Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
•  If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza | Alza.co.uk
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz
• alza.de
• alza.hu
• alza.sk
• Kyvol Official Site | Intelligent Robot Vacuum Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>