SHANGHAI M1 Bluetooth Headset User Guide

SHANGHAI M1 Bluetooth Headset

Product Information

Specifications:

• Model: MVFUPPUI
• Compliance: FCC Part 15

Product Usage Instructions

Compliance with FCC Rules:

This device complies with part 15 of the FCC Rules. To ensure proper operation, please adhere to the following conditions:

1. This device must not cause harmful interference.
2. The device must accept any interference received, including undesired operation.

Modifications:

Any changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment. Please refrain from making unauthorized alterations to the device.

FCC ID Information:

The FCC ID for this device should be prominently displayed. Please refer to the product labeling for the correct FCC ID information.

FAQ

What should I do if the device is causing interference?

If the device is causing interference, try relocating it or adjusting its position. Ensure that it is not placed near other electronic devices that may be affected by the interference.

Can I make modifications to the device?

Modifications to the device are not recommended unless expressly approved by the party responsible for compliance. Unauthorized modifications may impact the device’s functionality and compliance.

PACKAGE CONTENTS

Does not include wall charger, please prepare a wall charger with a specification of 5v 0.5-2A for charging

Charging

Type-C
DO NOT charge the headphone through apple Type-C cable, charge it via the type-C cable which is in includes.
Headphone is charging via Type-C cable, when finished, LED indicator light will be changed from (Long bright) to (Long bright).

• Charging time: when charge it for the first time, it should be more than 4 hours and less than 8 hours, to activate the best use of the battery, and after that, each charging only needs 2-3 hours.
• Low battery: Alarming once for each 3 minutes and accompanied by a ” Low battery please charge” voice prompt.
• Please disconnect the Type-C cable when the headset is fully charged, since overcharge will shorten the battery life.

Base

1. Find the charging pins of the headset and base, and put the headset down.
2. The LED lights of the base and headphones are red, indicating that they are charging.
3. After fully charged, the base and headphones of LED lights will be  and blue respectively.
4. Hold the headset close to the base when picking it up. The base and headset will enter an automatic connection state(LED lights of the base and headphones breathe blue). If the LED light of the headset or base flashes red and blue alternately, please refer to the troubleshooting on page 17.

Check your Device’s Output Ports

Connection and Use

NOTE: If the light of the Transmitter or headphone is red and blue alternately and cannot be connected, please refer to page 17 (Troubleshooting).

Optical Connection (Recommended)

Turn on

1. Get power to the transmitter with the wall charger/PC, then turn on the headset. You will hear the “power on” from the headphones.

2. Pairing(LED lights of the base and headphones breathe blue).
   The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally. They are paired.

3. Turn on TV and play sound, enjoy it.
   NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.
   The base is connected to a 3.5mm audio cable and an optical cable at the same time, the base will output the 3.5mm audio cable first. If only the optical fibe output is used, the 3.5mm cable should be unplugged.

RCA (red/white) Connection

Plug in
Please check whether the RCA interface of your TV is an audio output interface before connecting.

Turn on

1. Get power to the transmitter with the wall charger/PC, then turn on the headset. You will hear the “power on” from the headphones.

2. Pairing(LED lights of the base and headphones breathe blue).
   The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally.
   They are paired.

3. Turn on TV and play sound, enjoy it.
   NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.

3.5mm Connection

Plug in

Turn on

1. Get power to the transmitter with the wall charger/PC, then turn on the headset. You will hear the “power on” from the headphones.

2. Pairing(LED lights of the base and headphones breathe blue).
   The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally.
   They are paired.

3. Turn on TV and play sound, enjoy it.
   NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.

Connect to mobile phone bluetooth

1. Please confirm whether the LED light of the headset is red and blue alternately before connecting.
   If not, please long press Multifunction Key for 5 seconds. Then turn on the mobile phone bluetooth. Keep the headset as close to the phone as possible.

2. Search for a device named “BKM500″| on your phone, then click connect.

3. A few seconds later the connection was successful.
   The LED of headphone is blue and flashes slowly, and the phone shows that it is connected. You can hear it in your headphones: Your headset is connected.
   NOTE: Need to manually connect to mobile phone every time. When the mobile phone and the transmitter are turned on at the same time, the headset will automatically connect to the transmitter.

TV Setting

NOTE: Other TVs are similar to the settings. Or contact your TV manufacturer for more details.

Operating Instructions

Multifunction Key

1. Pause/Play music

2. Clear pairing history: Press the Multifunction key and the” -” key at the same time.
   Unable to connect again after clearing, you need to re-pair. This function cannot be used in the call state.

3. Pairing mode: Long press the Multifunction Key for 5 seconds

4. Voice dialing system: Long press the Multifunction key for 1 second.
   You can hear the beep in the headphone.
   (Only available when connected to the mobile phone)

5. Restart the headphone: Long press the Multifunction key for 10 second.

6. DUT model: In the pairing mode, press the Multifunction key and *-” key at the same time for 5 seconds to enter the DUT mode. Exit DUT mode after turning off the headset.

Equalizer Mode Key
In the connected state, click the EQ mode key to switch to different EQ modes to experience different sound effects.
Witching sequence: Pop-Rock-Movie. Defaults to popular mode at the startup.

Power On/Off Key:
After the startup, it automatically enters the pairing state when no device is bound. Enter the connection back state when there is a bound device.

Multifunction Key

1. Clear pairing history: Please turn off the paired headset first, and long press the Multifunction Key for 10 seconds to clear all connected devices (Red and blue lights are on for 3 seconds at the same time ) . After clearing, it will automatically enter the pairing state.
2. Pairing mode: Long press the Multifunction Key for 5 seconds.

Automatic connection:
After power on, the base will automatically connect to the last successfully paired device when there is a pairing record.
The base will automatically connect to the bound device after binding

Note: After Clear pairing history, you need to re-pair and bind the device, otherwise the base will not be able to enter the automatic connection state when it is turned off and then turned on.

Replace the bound device

The supporting equipment has been bound at the factory, and the base and the headset can be automatically connected after turning on. If you need to bind the base with another BKM500 headset, please refer to the following steps:

1. Clear pairing history: Please turn off the paired headset first. Then long press the Multifunction Key for 10 seconds, the red and blue lights are on for 3 seconds at the same time, which means that the base has been emptied successfully.
2. Pair: The base automatically enters the pairing mode after clearing successfully, please check whether the LED light of the headset is flashing red and blue alternately, if not, please long press the Multifunction Key for 5 seconds.
3. Connected successfully: The blue LED light of the base is always on, and the blue LED light of the headphone flashes occasionally. You can hear the sound. Represents a successful connection.
4. Headphones bound to the base: After the pairing is successful, you need to bind the headset to automatically connect the next time you turn it on. please double-click the base to bind (the LED light of the base will flash red 5 times).
   NOTE: Re-binding another headset may result in prolonged connection times in the future.

Troubleshooting

LED Indication

Product specifications

Headphone

Base

After-Sale Service

1 Year Full Warranty
Any problem? Reach out to us at dilbkm1@163.com, our specialists will be sincere to help you.
Your satisfaction is our number one priority!

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Shenzhen shi dichuangxiang ke ji you xian gong si

E-mail: dilbkm1@163.com
Address: jinglongdadao 16hao dong sheng shi dai 6 A 25D ping shan qu Shenzhen guangdong, China

Bluetooth Headset FCC ID: 2BFR6-M1 ;
Bluetooth transmitter FCC ID: 2BFR6-M1A

Documents / Resources

| SHANGHAI M1 Bluetooth Headset [pdf] User Guide
M1, M1 Bluetooth Headset, Bluetooth Headset, Headset
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>