Shanghai Xiangcheng Communication Technology P8 AI POS Terminal User Guide

Shanghai Xiangcheng Communication Technology P8 AI POS Terminal

Technical Specs

ATTENTION

Warning

• Read all instructions and safety information before use to avoid injury.
• The limit operating ambient temperature of the device declared by the manufacturer is -10~45°C.

Battery safety

• Charge battery only at ambient temperatures ranging from 0~40°C.
• Dispose of used batteries according to manufacturer’s instructions.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer.

Statement

• The equipment damage caused by natural disasters, falling, self disassembly and non-compliance with the operation specifications is not covered by the free warranty.
• Some details of this document may be inconsistent with the real object due to the update iteration of the product. Please take the real object as the standard, and our company reserves the right to interpret this document.

Product Diagram

• NFC Card Reader
  NFC antenna locates at the bottom of the screen and on the printer cover. It’s used to sense chip and acquire data through contactless way.

• IC Card Reader
  Used for inserting the bank chip card and getting information securely.

• Magnetic Stripe Card Reader
  Used for reading encrypt information stored in corresponding cards.

• Camera
  Used for taking photos, unlock the device by face recognition and complete intelligent recognition base on it.

• Scanner
  Used to capture and identify 1D and 2D code.

• Power Button
  Used for change the running states of device, such as pressing 2~3 seconds to power on/off or screen capture and pressing 10 seconds to restart automatically when device is crashed.

• Function Button
  Used for adjusting the volume or serving as the shortcut of scan. The function can be customized.

• Pogo pin
  The 8-pins expanded interface is severed as the channel to connect the charging cradle for better power supply or finish data transmission between different devices.

• Hand Stripe Ring
  Used to fix the hand strap for easy carrying.

Card Selection Instruction

Printer instructions

1. Support 2 inch thermal paper roll with specification of 5740mm (wφ)
2. Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter;

Note : If the printed paper is blank, please check whether the pap-er roll has been installed in the correct direction.

Package List

FCC STATEMENT

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this standard during product certification for use next to the Body with the minimum separation distance of 0mm. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is compliance to FCC RF Exposure requirements and refers to FCC website

https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm
search for FCC ID: 2A2UU-P8 All transmission frequencies of U-NII-1,U-NII-2A and U-NII-3 comply with 47 CFR FCC Part15.407(g) and the manufacturer declares that their transmission is maintained within the U-NII-1, U-NII-2A and U-NII-3 bands.

References

• FCC OET Authorization Search

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>