Prorenfort PRO-E-2232 Warning Light Bar Instruction Manual
- June 1, 2024
- Prorenfort
Table of Contents
Prorenfort PRO-E-2232 Warning Light Bar
Product Information
Specifications:
- Series: E-2232
- Product: Warning Light Bar
- Power Source: Cigarette Power Adaptor
Product Usage Instructions
Pattern Selection:
This Light comes with a Cigarette Power Adaptor. Press the button once to change patterns.
Flash Patterns:
| NO. | Flash Patterns |
|---|---|
| 1 | Random Patterns |
| 2 | Alternating Single Flash / Simultaneous Quad Flash |
Installation Safety Instructions:
-
* Properly install with an understanding of automotive electronics systems.- Ensure a proper fuse is installed.
- Avoid damaging vehicle components during installation.
Cleaning and Maintenance:
Use only soap and water to clean the outer lens. Do not use a pressure washer. Regularly inspect and operate the product to ensure proper functioning.
Grounding:
For optimum efficiency, make a good electrical connection to chassis ground by connecting the ground wire directly to the NEGATIVE [-] post or a solid metal body/chassis part.
FAQ
Q: Can I mount the warning light using magnets?
A: As roof construction and driving conditions vary, the use of any magnetic or suction cup mounted warning light on the outside of a vehicle while in motion is not recommended and is at the sole discretion and risk of the user.
Pattern Selection
This Light comes with a Cigarette Power Adaptor;
Press button once to change patterns
This unit may not be factory-set to Flash Pattern #1 Note: Cutting wires voids the warranty
Flash Patterns
- Random Patterns
- Alternating Single Flash / Simultaneous Quad Flash
- Steady Light
- Alternating Triple Flash
- Alternating Single Flash
- Alternating Quad Flash
- Simultaneous Single Flash
- Simultaneous Double Flash
- Alternating Triple Flash / Simultaneous Triple Flash
- Alternating Single Flash / Alternating Triple Flash / Simultaneous Triple Flash
- Simultaneous Quad Flash
- Simultaneous Single Flash
SAFETY FIRST – READ THIS INFORMATION BEFORE INSTALLATION
- Proper installation of this product requires the installer to have a good understanding of automotive electronics systems and procedures.
- All products must have proper fuse installed.
- If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr any holes and removes any metal shards or remnants. Install grommets into all wire passage holes.
- If this manual states that this product may be mounted with suction cups or magnets, clean the mounting surface with 50/50 mix of isopropyl alcohol and water, then dry thoroughly.
- Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag deployment area. The user/installer assumes full reponsibility to determine proper mounting location based on providing ultimate safety to all passengers inside the vehicle. Install only where vehicle manufacturer recommends.
- For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE [-] post. At a minimum, it may be attached to a solid metal body or chassis part that will provide an effective ground path as long as the light system is to be used.
- If this product uses a device to activate or control this product, make sure that this control is located in the area that allows both the vehicle and the control to be operated safely.
- Do not attempt to activate or control this device in a hazardous driving situation.
- Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
- Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking [crazing] and discoloration. Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
- It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.
- FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
MAGNET INSTALLATION
WARNING: As roof construction and driving conditions vary, the use of any
magnetic or suction cup mounted warning light on the outside of a vehicle
while in motion, is not recommended and is at the sole discretion and risk of
the user.
Holding power of magnetic mounting systems is dependent upon surface finish,
surface flatness, and thickness of the steel mounting surface. Therefore, to
promote proper magnetic mounting;
- Mounting surface and magnets must be kept clean, dry and free of foreign particles that prevent good surface contact.
- Ensure that mounting surface is flat.
- To prevent sliding of light assembly on mounting surface, quick acceleration and hard stops should be avoided.
STROBE LIGHT
- WARNING: The strobe light power supply is a high voltage device. Do not remove strobe tubes or dismantle strobe lightheads in the system while it is in operation. Wait 10 minutes after turning off power before starting work or any troubleshooting.
An unfused installation may cause damage to equipment, fire, or injury to you or others. Ensure that a fuse is installed.
IMPORTANT ELECTRICAL WARNINGS!!
- DO NOT use a cigar lighter socket as a power source for this or any electrical accessory! Use a 12 volt accessory power port or auxiliary power outlet of sufficient capability. Do not exceed the manufacturers’ power rating for the selected port/outlet!
- DO NOT pull on the power plug wires when removing the plug from the outlet! To remove, firmly grasp the power plug housing and pull.
- ANY DEVIATIONS FROM THE ABOVE ELECTRICAL GUIDELINES WILL VOID THE PRODUCT WARRANTY.
- IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not interfere with or compromise the operation or efficiency of any vehicle equipment!
- IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle components and equipments.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>