Prorenfort PRO-E-2477AC 47 Inch Amber-White LED Safety Warning Light Bar Instruction Manual
- June 1, 2024
- Prorenfort
Table of Contents
- Prorenfort PRO-E-2477AC 47 Inch Amber-White LED Safety Warning Light Bar
- WARNING!!
- Wiring Information
- Flash Patterns
- Hardware List – Surface Mount – Bag 1
- Hardware List – Strap/Gutter Mount – Bag 2
- Mounting Installation – Surface Mount
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Prorenfort PRO-E-2477AC 47 Inch Amber-White LED Safety Warning Light Bar
Instruction Manual
WARNING!!
Failure to follow instructions can short-circuit lamp.
Installer must ensure that the Ground (black wire) be connected first before
connecting Power (red wire) or any other wires. Additionally, all wires MUST
only connect to Ground other than the Power (red wire) – refer to the Wiring
Information below.
Wiring Information
| Function | Wire Colour | Connect To |
|---|---|---|
| Ground | Black | – Ground |
| Power | Red | +12/24 V DC |
| Left Warning Signal | Brown | – Ground |
| Right Warning Signal | Orange | – Ground |
| Take-Down Light | Green | – Ground |
| Alley Light | Blue | – Ground |
| Flash Pattern Selection | Yellow | – Ground |
Lamp should be fused with a 10 Amp Fuse ( ATM10 sold separately )
Flash Patterns
| NO. | Flash Patterns |
|---|---|
| 1 | Random Patterns |
| 2 | Rotating Flash |
| 3 | Alternating Single Flash |
| 4 | Alternating Double Flash |
| 5 | Alternating Quad Flash |
| 6 | Alternating Quint Flash |
| 7 | Alternating Mega Flash |
| 8 | Alternating Ultra Flash |
| 9 | Alternating Single Flash / Alternating Quad Flash |
| 10 | Alternating Single Flash / Alternating High Intensity Single Flash |
| 11 | Alternating Double-Quad Flash |
| 12 | Alternating Single-Quad Flash |
| 13 | Simultaneous Single Flash |
| 14 | Simultaneous Double Flash [ SAE Class 1 ] |
| 15 | Simultaneous Quad Flash |
| NO. | Flash Patterns |
| --- | --- |
| 16 | Simultaneous Quint Flash |
| 17 | Simultaneous Mega Flash |
| 18 | Simultaneous Ultra Flash |
| 19 | Simultaneous 8 Single Flashes / 4 Quad Flashes |
| 20 | Simultaneous 8 Single Flashes / 6 Fast Single Flashes |
| 21 | Simultaneous Double Flash / Simultaneous Quad Flash |
| 22 | Simultaneous Single Flash / Simultaneous Quad Flash |
| 23 | Left Side Steady & Right Side Double Flash |
| 24 | Simultaneous Single Flash (2Hz) |
| 25 | Simultaneous Double Flash (2Hz) [ SAE Class 1 ] |
| 26 | Simultaneous Triple Flash (2Hz) |
| 27 | Simultaneous Quad Flash (2Hz) |
| 28 | Simultaneous Quad Flash (Split) |
| 29 | Steady Corner Light |
Hardware List – Surface Mount – Bag 1
Hardware List – Strap/Gutter Mount – Bag 2
Mounting Installation – Surface Mount
Step 6: Repeat Step 1 to Step 5 for the other side.
Step 7: Mount to vehicle using your own mounting bolts, not supplied. Make
sure to remove mounting pads shown in Mounting Diagram 1.
Step 1: Steps 1 to 6 of “Mounting Installation – Surface Mount” must be completed first before proceeding. Place the [ Lock Bracket ] x1 in position as shown in Figure 7-ii & using the [ M8 – Form A Flat Washer ] x1, [ M8 – Form A Spring Washer ] x1, [ M8 – Form A Hex Nut ] x1 & [ M8 – 45mm Hex Bolt ] x1, tighten the Lock Bracket in place as shown in Figure 7-iv. If instructions are unclear, please refer to the Mounting Diagram 2 below. Repeat this step for the other side.
Step 2: Following Mounting Diagram 1 & Mounting Diagram 2. Using the [
Tightening Hook ] x1, adjust according to vehicle (it is recommended to
mount along the B-Piller). Repeat this step for the other side.
Step 3: Once positioned, using the [ M6 – Form A Flat Washer ] x1, [
M6 – Form A Spring Washer ] [ M6 – Form A Hex Nut ] x1 & [ M6 – 15mm Hex
Bolt ] x1, tighten the Tightening Hook in place.
Refer to Mounting Diagram 3. Repeat this step for the other side.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>