Ardes AR5ST40PN 40PG Stand Fan Instruction Manual
- June 1, 2024
- Ardes
Table of Contents
INSTRUCTIONS FOR USE
STAND FAN
AR5EA40P – AR5ST40PN
AR5ST40PW-AR5ST40PG
WARNINGS
This appliance may be used by children 8 years of age and older and people
with reduced physical, sensory or mental capacities or with a lack of
experience and knowledge if they are adequately supervised or have been
instructed on the safe use of the appliance and are aware of the related
dangers. Children must not play with the appliance. leaning and maintenance
must not be performed by children unless they are under supervision.
Cleaning and maintenance operations must not be performed by children without
supervision. If the power cable gets damaged, it has to be replaced only at a
service centre approved by the manufacturer in order to prevent any risks.
Ensure that the fan is switched off from the supply mains before removing the
guard.
Don’t connect the appliance to the power supply and don’t use it unless it is
completely assembled (see mounting instructions).
ATTENTION : read this booklet carefully it contains important
instructions for a safe installation, use and maintenance. Important
instructions to be kept for future reference.
It is forbidden for the children to play with the device.
This device must be used only for the purpose it was expressly designed; any
use not complying with the instructions contained in the manual is considered
inappropriate and dangerous. The manufacturer is not responsible for possible
damages caused by the inappropriate and/or unreasonable use.
This device is NOT suitable to use it in an explosive environment (in the
presence of flammable substances such as gas, vapor, mist or dust, in
atmospheric conditions when, after ignition, the combustion is spread in the
air).
The packing materials (plastic bags, expanded polystyrene, etc.) must be kept
out of the reach of children or disabled persons since they represent
potential sources of danger.
The installation/assembly of the device will be made/ or according to the
indications of the manufacturer. A wrong procedure may cause damages to
persons, animals or objects, for which the manufacturer cannot be considered
responsible.
Place and use the device on a horizontal and stable surface.
Before use check the integrity of the device and power cable. In case you are
not sure contact a qualified person.
Before powering the device make sure the rating (voltage and frequency)
corresponds to the grid and the socket is suitable for the plug of the device.
Make sure the power system is equipped with proper protection according to the
law in force.
DO NOT power the device using multiple sockets.
If possible, avoid the use of adapters and/or extension cables; if their use
is absolutely necessary, use only materials in compliance with the current
safety regulations and according to the electrical parameters of the adapters.
The device must not be switched on using external timers and/or other remote
control devices which are not specified in this manual.
DO NOT use or store the device near heat sources (heaters, stoves etc.).
DO NOT dip the device in water or other liquids; in case the accidental fall
in the water DO NOT try to take it out, but first of all unplug immediately
the power cable from the socket.
If you use the device for the first time, make sure to remove any label or
protective sheet which blocks its proper functioning.
Plug and unplug the power cable with dry hands and hold it firmly.
Before plugging make sure the start button of the device is in the “OFF”
position (turned off).
Always unplug the power cable to avoid the overheating and avoid stretching it
(do not pull it, tug it or use it to drag the device to which is connected).
Avoid placing the power cable on abrasive or sharp surfaces or in positions
where it can be damaged easily.
DO NOT obstruct totally nor partially the air vents or inserts objects inside.
During the functioning do not touch the device with wet body parts, and in any
case it is recommended to have between you and the standing surface, an
isolating element (for ex. wearing shoes with rubber soles).
During the use the device must be keep at a safety distance from any object
and/or flammable or potentially explosive substance.
In case of malfunction or anomalies during the functioning, switch off the
device immediately, turn off the power and check the cause of the anomalies,
if possible, with the support of a qualified person. Avoid carrying out
operations which are not specified in this manual (such as disassembling
and/or altering).
Always remember to unplug the power cable of the device if it is not used for
a long period, before storing, cleaning or performing any maintenance
operation.
Store and use the device only indoor or in any case protected from weathering
such as rain, direct radiation of the sun and dust. The device is not design
for the external use or storage.
The cleaning and maintenance of the device MUST NOT be done by children
without the supervision of an adult.
Before unplugging the device, switch it off, using the proper command on the
control panel.
DO NOT hang the fan on the wall or ceiling unless this type of installation is
provided and explained in this manual.
Place the device at a proper distance from the objects or surrounding walls
making sure that its functioning will not cause accidental damages.
DO NOT use the device near gas stoves or open flames in general.
DO NOT use the device near curtains or textiles.
DO NOT hang the fan on the wall or ceiling unless this type of installation is
provided and explained in this manual.
DO NOT cover the device during functioning.
DO NOT insert objects or body parts inside the protection grille of the fan.
DO NOT leave the device unsupervised for a long period during functioning.
DO NOT expose yourself for a long period to the air flow generated by the
device because it can cause damage to the health.
If the fan must be stored for a long period and is not used regularly, place
the fan in its original packaging in a dry place. When you use it for the
first time after a long period of inactivity, make sure the fan is clean and
the motor blades turn feely (with the device not powered) without any
restraint.
ASSEMBLING
(see image at last page)
- Front grille
- Lock ring of the fan
- Safety screw of the fan
- Fan
- Lock ring of the back grille
- Back grille
- Motor shaft
- Oscillation knob
- Motor
- Control panel
- Main body screw
- Adjustment rod
- Height adjustment knob
- Base rod
- Feet (4 pieces)
- Bracket
A-B. Locking pin for the rear grille
INSTRUCTIONS FOR USE
Place the fan on a flat, dry and stable surface, and insert the plug of the
fan in a socket. Select the desired speed by pressing the buttons on the
control panel (10):
0 = off 1 = minimum speed 2 = medium speed 3 = maximum speed
OSCILLATION:
For the automatic oscillation from right to left press the knob (8) placed on
top of the motor. To disable it, pull up the knob.
VERTICAL SLOPE:
You can vertically point the front of the fan choosing the desired angle. It
is sufficient to move the front of the fan up or down according to the desired
slope.
ADJUSTMENT HEIGHT
Loosen the height adjustment knob (13), then set the desired height for the
fan. Tighten firmly the knob after adjusting the rod.
N.B: this operation must always be carried out while the fan is turned off.
MAINTENANCE
Before carrying out the regular cleaning operations turn off the fan and
unplug it.
Ensure that the fan is switched off from the supply mains before removing the
guard.
For external cleaning use a soft and dry cloth.
DO NOT dip the device in water, or splash it with any other liquids.
DO NOT use solvents or any other chemical products for cleaning it.
Reinstall the guard after cleaning and before connecting the plug tot he
mains.
When you do not use it, after cleaning it, store the fan in a dry place.
USER INFORMATION
PACKAGING
In order to respect the environment, packaging material must be disposed of
properly in accordance with separate collection.
Check local regulations.
USER INFORMATION
**** “Implementation of Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE)”, pertaining to reduced use of hazardous
substances in electrical and electronic equipment, as well as to waste
disposal.
The symbol of the crossed-out wheelie bin on the equipment or on its packaging
indicates that the product must be disposed of separately from other waste at
the end of its service life.
The user must therefore take the dismissed equipment to suitable separate
collection centres for electrical and electronic waste. For more details,
please contact the appropriate local authority. Suitable segregated collection
of the equipment for subsequent recycling, treatment or environmentally
friendly disposal helps prevent damage to the environment and to human health,
and encourages the re-use and/or recycling of the materials that make up the
equipment. Abusive disposal of the product by the user shall result in the
application of administrative fines in accordance with the laws in force.
GUARANTEE
Terms and Conditions
The guarantee is valid for 24 months.
This guarantee applies only if it has been duly filled in and is submitted
with the receipt showing the date of purchase.
The guarantee covers the replacement or repair of parts making up the
appliance which were faulty at source due to manufacturing faults.
After the guarantee has expired, the appliance will be repaired against
payment.
The manufacturer declines any responsibility for damage to persons, animals or
property due to misuse of the appliance and failure to observe the directions
contained in the instructions.
Limits
All rights under this guarantee and any responsibility on our part will be
voided if the appliance has been:
– mishandled by unauthorized persons
– improperly used, stored or transported.
The guarantee does not cover damage to the outward appearance or any other
that does not prevent regular operation.
If any faults should be found despite the care taken in selecting the
materials and in creating the product, or if any information or advice are
required, please contact your local dealer.
ASSEMBLING
Poly Pool S.p.A. Via Sottocorna, 21/B
24020 Parre (Bergamo) – Italy
Tel. +39 035 4104000 r.a.
Fax +39 035 702716
http://www.ardes.it
e-mail: [email protected]
MADE IN CHINA