Ardes AR5A107D Ceiling Fan With Light User Manual
- June 1, 2024
- Ardes
Table of Contents
INSTRUCTIONS FOR USE
CEILING FAN WITH LIGHT
AR5A107D
AR5A107D Ceiling Fan With Light
Warnings
This appliance may be used by children 8 years of age and older and people
with reduced physical, sensory or mental capacities or with a lack of
experience and knowledge if they are adequately supervised or have been
instructed on the safe use of the appliance and are aware of the related
dangers.
Children must not play with the appliance.
Cleaning and maintenance operations must not be performed by children without
supervision.
This appliance must be installed by professionally qualified personnel.
Since the installation of the equipment sets, the power of the network must be
done, according to the installation rules, through flexible cable plug or by
all pole switch that provide full disconnection under overvoltage category III
conditions.
Contacts opening distance shall not be less than 3 mm.
Equipment must be installed at the height of at least 2,3 meters from the
floor (2,3 meters means from the floor to the bottom of the fan).
WARNING: when the appliance is connected to the mains, do not touch the
rotating blades and stay away from them.
This appliance can operate at 50Hz or 60Hz without adjustments.
ATTENTION : read this booklet carefully it contains important
instructions for a safe installation, use and maintenance.
Important instructions to be kept for future reference.
Remove the packing and make sure that the appliance is intact. In case of
doubt do not use it and address to an after-sales service recommended by the
manufacturer. Do not allow packaging materials like bags and staples can be
reached by children.
Before connecting the appliance, check if the electrical voltage and frequency
of the circuit correspond to those indicated on the appliance.
The manufacturer is not responsible for any eventual damages caused by
improper or faulty use.
The unit must be connected to a good ground conductor Equipment must be
installed at the height of at least 2,3 meters from the floor (2,3 meters
means from the floor to the bottom of the fan).
Since the installation of the equipment sets, the power of the network must be
done through flexible cable plug or by pole switch with contact opening
distance not less than 3 mm.
For the installation of the apparatus used a cable type H05 VVF.
Before maintenance and cleaning operations turn off the product and disconnect
from the mains power supply turning off the system switch.
This appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and off by
the utility.
If the appliance is out of work, switch it off without tampering it. If any
repair is required please contact only our after-sales centres and ask for
original spare parts. Otherwise safety of the appliance can be compromised.
The use of every electrical appliace calls for the awareness of some basic
rules, such us:
-do not touch the appliance with wet hands or feet
-never expose the appliance to atmospheric conditions (rain, sun…)
Do not use the device in the presence of potentially explosive or flammable
liquids or gases.
Do not leave the appliance plugged in when not in use. Swith it off and unplug
it when it is not in use.
Technical informations
- Screw terminal
- Support plate
- Support hook
- Support rod
- Screws for fixing the cap (4 pcs.)
- Cap
- Pin for fix the support rod
- Safety stopper and washer
- Motor
- Switch for reversible function
- Screws for fix the decotative glass
- Lamp holder
- Decorative glass
- Screws for secur the blades to the motor
- Blades
- Blades support
- Screws and nuts for secur the blades to the blades support
- Pull cords chain
Assembling
Make sure you have all the components before
beginning installation. To prevent damage, attach the motor to the support rod
on a soft surface or use the polystyrene contained in the package.
-Open the carton box and take out the fan (fig. 1)
-Assemble the support plate on the ceiling using two or more screw anchors and appropriate washers. Attention: the provided screw are for wood joist. The electric cables coming out from the ceiling must be insert on the central holes of the support plate (fig. 2).
– Remove the safety stopper and washer from the safety pin then remove the
safety pin from the support rod (fig. 4). Insert the support rod through the
cap.
-Loosen the screw placed on the bottom part of the support rod and insert the electric cables coming out from the motor through the support rod (fig. 5).
-Fix the support rod to the motor housing using the safety pin and lock it using the washer and the safety stopper (fig. 6 and 7).
-Tighten the screw placed on the bottom part of the support rod (fig. 8).
-Unscrew the 4 screws placed on the support plate.
-Hang the fan to the hook on the support plate using the cap’s hole and connect the electrical cables (fig. 9). NB: arrange the electrical connection as shown in fig. 3.
-Remove the fan from the hook and fix the cap to the support plate making sure the holes of the cap are coincident to the holes of the support plate. Fix the cap by using the 4 screws previously unscrewed.
ATTENTION: make sure to tighten the screws very well and that the groove
of the plastic ball fit the jut of the cap (fig. 10).
-Fix the blade support to the blades by using the provided screws and nuts (fig. 11). N.B: The blades are double face – one side is wood and another side is wood with straw insert. Before fix the blades support take care of the blades’s side that you prefer.
-Unscrew the screws and washer from the motor and remove the paper protection. Place the blades with blade support on the motor making sure that the holes are coincident and fix them by using the washer and screws previously unscrewed (fig. 12).
-Install the light bulb (E27 type Max 60W not provided) in the lamp holder -Install the decorative glass and fix it using the provided screws. Take care to do not tight the screws too much or the decorative glass can get broken (fig. 13).
ELECTRICAL CONNECTION:
Instructions for use
The ceiling fan is provided with 2 pull cord chain and switch for reversible
function that allows to invert the rotation of the blades.
The pull cord chains control the light and the speed; the function of the pull
cord chains are as below:
Speed pull cord chain: you can select maximum speed (pulling the chain once),
medium speed (pulling the chain twice) or minimum speed (pulling the chain
thrice).
Light pull cord chain: you can turn on or off the light of the fan.
Maintenance
Before carrying out the regular cleaning operations and before replacing the
lamp turn off the fan and disconnect it from the electrical supply.
For external cleaning use a soft and dry cloth.
DO NOT dip the device in water, or splash it with any other liquids.
DO NOT use solvents or any other chemical products for cleaning it.
User Information
PACKAGING
In order to respect the environment, packaging material must be disposed of
properly in accordance with separate collection.
Check local regulations.
DISPOSAL
USER INFORMATION
“Implementation of Directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE)”, pertaining to reduced use of hazardous substances in
electrical and electronic equipment, as well as to waste disposal.
The symbol of the crossed-out wheelie bin on the equipment or on its packaging
indicates that the product must be disposed of separately from other waste at
the end of its service life.
The user must therefore take the dismissed equipment to suitable separate
collection centres for electrical and electronic waste.
For more details, please contact the appropriate local authority.
Suitable segregated collection of the equipment for subsequent recycling,
treatment or environmentally-friendly disposal helps prevent damage to the
environment and to human health, and encourages the re-use and/or recycling of
the materials that make up the equipment.
Abusive disposal of the product by the user shall result in the application of
administrative fines in accordance with the laws in force.
GUARANTEE
Terms and Conditions
The guarantee is valid for 24 months.
This guarantee applies only if it has been duly filled in and is submitted
with the receipt showing the date of purchase.
The guarantee covers the replacement or repair of parts making up the
appliance which were faulty at source due to manufacturing faults.
After the guarantee has expired, the appliance will be repaired against
payment.
The manufacturer declines any responsibility for damage to persons, animals or
property due to misuse of the appliance and failure to observe the directions
contained in the instructions.
Limits
All rights under this guarantee and any responsibility on our part will be
voided if the appliance has been:
– mishandled by unauthorized persons
– improperly used, stored or transported.
The guarantee does not cover damage to the outward appearance or any 0other
that does not prevent regular operation.
If any faults should be found despite the care taken in selecting the
materials and in creating the product, or if any information or advice are
reauired. olease contact vour local dealer.
AR5A107D.181123
Poly Pool S.p.A. Via Sottocorna, 21/B
24020 Parre (Bergamo) – Italy
Tel. +39 035 4104000 r.a. – Fax +39 035 702716
http://www.ardes.it
e-mail: polypool@polypool.it
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>