Menglang 6S Over-Ear Hi-Fi Stereo Foldable Wireless Headphones Instruction Manual

Menglang 6S Over-Ear Hi-Fi Stereo Foldable Wireless Headphones

Package Contents

Before use

1. Tum off the headset.use the charging cable to connect the charger/computer/charging bank/etc to charge;
   Note: Before using the headset for the first time charge for at least 2 hours;

2. The red LED will tum on to indicate that the unit is charging; Once fully charged,the red LED will tum blue. Tips: Do not tum on the headset when charging the headset, or else it will lower the quality and the life of the battery.

CONNECT

1. Place headset within 3Sftfrom Bluetooth-enabled device.
2. ****Long press, the headset will be turned on. You will hear a prompt.
3. After opening the phone Bluetooth,dick the < 6S > to pairing.
4. The headset will automatically tum off after half an hour without pairing.
   NOTE : If the red and blue lights flash alternately,the Bluetooth is not connected; The BLUE light is always Or\ indicating that the Bluetooth is connected; Red light alw on, indicating that the headset is low battery/tUm off/charging.

AUDIO LINE

Operation

POWER BUTTON

• Power on/Off
• Tum on/off the headphone

VOLUME

• NexWolume+
• Press once: the next song/channel Long press: increase the volume

AUDIO

1. Audio 1/0 Interface
2. Connect the external device with 3.5mm audio cable, achieve audio output, e.g.speaker.

MIC

• MIC

LIGHT

• Indicator light

CARD SLOT

• TFcard slot
• Insert TF card, playing MP3 song files

CHARGE PORT

• Micro Charging Port.

VOLUME

• Previous/Volume-
• Press once: the previous song/channel Long press: decrease the volume

CALL BUTTON

• Play/pause/call control
• Control music and calls

M

• Equalizer/Bluetooth/FM/TF
• Press once to change the sound effect(6 choices); Long press 3s to switch the mode among Bluetooth, FM, TF.

Safety Information

• If no pairing connection after the headset enters the pairing mode, please tum off the headset to save power.
• Do not perform other operations while pairing the headset to prevent the program error.
• Please select a proper volume while using to prevent damage to your ears.
• Please note that a good environment for using the headset can avoid damage to the headset
• Please charge the headset after a long time of none-use.
• When it’s charging with a USB cable, please tum off the power in order to avoid noise.

Reset

If headphones have any connection or function problems, please reset the headphones.

1. Delete the Bluetooth pairing information on the phone.
2. Long press the M button for 3 seconds until the flash quickly with red and blue.
3. Connect to the phone Bluetooth again. (If the above operation does not woric, please try again.)

Specification

Model Distortion Play Mode SensitMty Driw,

Speaker material Charge time

Temperature

| 6S

s 1%At lKHz Wired/Wireless 10S±.3dB

40MM

NsFeB

.!:1 hours 1S”Cto3 S”C

| Type

Frequency Range Impedance ReceiveRange Frequency Range Max support Battery Capacity

Charge port

| Headset 2.4-2.483SG

320

10Meter 20HZ-20KHz

32G

SOOmAh

USB

---|---|---|---

Q&A

1. Q: Does the Mic work while wired?
   A:Yes; You need to plug in the 3.5mm audio cable In order to ensure better sound reception,you can call at the microphone

2. Q: Can the Bluetooth headphones be paired with multiple devices? A:.lt is recommended that you do not connect two devices at the same time, which may cause Bluetooth interruption or channel error, If another device
   is not needed, it is recommended to cancel Bluetooth pairing directly

3. Q: How to use FM mode?
   A: Long press the M key to enter the radio mode. Continue to press the middle key to search for the radio signal. The radio mode can only sound after searching forthe radio signal.

4. Q: What if the Headphones is defective OR it just doesn’t meet your expectation?
   A: We admit that the headphones might be defective on rare occasions.
   If that happens, please contact us. and we will give you a satisfactory reply within 24 hours.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>