VICTA 2691588-B Mulchmaster 560 Lawn Mower Owner’s Manual

June 5, 2024
VICTA

VICTA 2691588-B Mulchmaster 560 Lawn Mower

VICTA-2691588-B-Mulchmaster-560-L

Deck Group

Note:
Unless noted otherwise, use the standard torque specifications

  • 20 CH86859AW 1 CHASSIS, 560, Aztec Silver
  • 25 —– 1 GEARBOX CURTAIN
  • (Not a serviceable part)
  • 30 CH85985A 1 PLUG, 4 Stroke Models Only
  • 40 CH86939AW 1 BUMPER
  • (Includes screws) 50 CH86897AW 1 WEAR PLATE PACK
  • (Includes screws & washers)60 CH86861AW 1 SEGMENT
  • 70 —– 1 MULCHING PLUG
  • (Not a serviceable part) 80 CH86885AW 1 KNOB, Mulch Plug
  • 90 CH86893AW 1 MULCH PLUG PACK
  • (Includes Ref. Nos. 70 & 80)
  • 100 CH87226A 1 DISCHARGE FLAP ASSEMBLY
  • 110 CH86895AW 1 CHUTE PACK
  • (Includes screws & washers) 120 CH86899AW 1 SKID PLATE PACK
  • (Includes screws & washers)
  • 140 CH88436A 1 REAR FLAP PACK, 560
  • 160 CH86898AW 1 BELT COVER PACK
  • (Includes screws & washers)

Engine & Blade Group

Note:
Unless noted otherwise, use the standard torque specifications

  • REF NO PART NO QTY DESCRIPTION
  • 10 123P32-0031-H5 1 ** ENGINE, Briggs & Stratton 850 Series
  • 80 HA21320D 3 BOLT, Taptite, HW, 3/8 UNC x 30
  • 90 HA22277D 3 WASHER, Engine Mounting
  • 271 EE14476A 1 PULLEY & SLEEVE, Engine, 4-Stroke, 7/8″
  • 290 CA09442G 1 BLADE DISC, Oval
  • 300 —– 2 BLADE, Mower, Lo-Lift
  • 305 CA09507B 2 BLADE, Hi Lift
  • 310 —– 2 BOLT, Blade
  • 320 CA09347A 2 WASHER, Blade Tension
  • 330 HA25276BZ 2 WASHER, Belleville
  • 340 CA09241D 2 NUT, Nylock, 3/8 UNC
  • 350 EE14484B 1 BOLT, Flanged, Blade Disc
  • 360 EN73054B 1 WASHER, Blade Disc
  • 370 CA09276B 1 KIT, Blade & Bolt, Hi-Profile (1 Pair)
  • (Includes Ref. No. 305, 310, 320, 330 & 340) 380 CA09584B 1 KIT, Blade & Bolt, Lo-Lift (1 Pair)
  • (Includes Ref. No. 300, 310, 320, 330 & 340)
  • 390 CA09277S 1 KIT, Hardware, Bolt, Washer, Nut (1 Pack)
  • (Includes Ref. No. 310, 330 & 340) 400 CA09277P 1 KIT, Hardware, Blade, Washer, Nut , Bulk Pack (50 Pairs)
  • (Includes Ref. No. 310, 330 & 340)

Note
Engine Style may vary from illustration. To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service.

Handles & Controls Group

Note:
Unless noted otherwise, use the standard torque specifications

  • REF NO PART NO QTY DESCRIPTION
  • 20 HA20492D 4 BOLT, Hex Head, M8 x 65
  • 30 CH87047GW 2 HANDLE, Lower, 560
  • 40 CH80854GZ 2 PLATE, Saddle, Heavy
  • 50 VV17130D 2 PLATE, Saddle
  • 60 —– 4 NUT, Nylock, M8
  • 70 CH88061P 1 WINGED LOCKING LEVER PACK V2
  • (2 Sets Included, Kit includes Lever, Washer & Nut)
  • 100 CH87048G 1 HANDLE, Upper, 560 S/P
  • 120 CH88439A 1 BAIL ARM ASSEMBLY
  • 130 HA24982D 1 NUT, Nylock, M6
  • 140 CH86788A 2 SLEEVE, Bearing
  • 150 80079136 1 UPPER HANDLE ASSEMBLY
  • (Includes Ref. Nos. 100, 120, 130, 140 &160)
  • 160 CH87424A 1 CABLE, Drive Clutch
  • 170 —– 1 CLAMP, 22mm
  • (Not a serviceable part)
  • 80 —– 1 SCREW, M5 x 18
  • (Not a serviceable part)
  • 200 TC05064B 1 THROTTLE, Pro Control
  • (Includes Ref. Nos. 170 & 180)
  • 220 CH86896AW 1 TENSIONER MOUNT PACK 560

Wheels Group

Note:
Unless noted otherwise, use the standard torque specifications

  • 10 —– 4 SCREW, Hex Flange, M5 x 16 (Not a serviceable part.)
  • 20 —– 6 SCREW, Pan Torx Trilobe, M6 x 19 (Not a serviceable part.)
  • 30 —– 1 * SCREW, Pan Torx, Self Tap, ST4.2 x 16 (Not a serviceable part.)
  • 40 CH84142A 2 RING, Sealing
  • 50 CH84185U 2 BUSHING, Rear Axle
  • 70 —– 1 * SCREW, Pan Torx, Self Tap, ST4.2 x 10 (Not a serviceable part.)
  • 80 —– 2 SLEEVE, Fixed
  • 85-1 —– 1 SPRING, RH, Black (Not a serviceable part.)
  • 85-2 —– 1 SPRING, LH, Yellow (Not a serviceable part.)
  • 90 —– 1 DRIVE GEAR(Not a serviceable part.)
  • 95 —– 1 SLEEVE, Drive(Not a serviceable part.)
  • 100 —– 2 PIN, Roll 1/8 x 3/4 SP(Not a serviceable part.)
  • 110 CH86881AW 1 AXLE, Front
  • 120 CH86276A 2 BUSHING, Front Axle
  • 130 CH81445A 4 DUST SEAL
  • 140 80084367 2 BEARING(Replaces Part Nos. HA25463A)
  • 150 CH88275D 4 RETAINING PLATE, Axle
  • 160 CH87420A 1 BRACKET, Gearbox 560
  • 180 80080431 1 KIT, Variable Speed
  • 185 CH87296A 1 GEARBOX GT-MC600
  • 190 CH86938AW 1 AXLE, Rear
  • 190-1 —– 1 GEAR, Over – Run Clutch, RH Black(Not a serviceable part.)
  • 190-2 —– 1 GEAR, Over – Run Clutch, RH Yellow(Not a serviceable part.)
  • 200-1 CH86816S 1 OVER RUN CLUTCH KIT
  • 200-2 CH86823S 1 OVER RUN SPRING KIT
  • 210 CH85943A 1 SPRING
  • 220 HA25131D 2 E-CLIP
  • 240 CH82847A 2 SEAL, Drive Wheel
  • 250 CH86334A 4 WHEEL, Pro, 8″
  • 260 CH86333A 2 WHEEL, Pro, 8″, REAR
  • 250-1 —– 2 WASHER, Wheel, Front(Not a serviceable part.)
  • 250-2 —– 2 BUSHING, Wheel, Front(Not a serviceable part.)
  • 250-3 —– 2 WASHER, Wheel, Front
  • 251 CH86298A 4 CAPTIVATED CLIP, Wheel
  • 350 CH86112A 4 HUBCAP, Black
  • 370 CH86862AW 1 CONLINK
  • 400 80085135 1 V-BELT, 6736 Power Rated (Replaces Part Nos. CH85666A)

Hardware Identification & Torque Specifications

The guides and ruler furnished below are designed to help you select the appropriate hardware.

Standard Hardware Sizing
When a washer or nut is identified as 1/2” (M8), this is the Nominal size, meaning the inside diameter is 1/2 inch (8mm metric thread diameter); if a second number is present it represents the threads per inch (distance between threads). When bolt or capscrew is identified as 1/2 – 16 x 2” (M8 – 1.25 x 50), this means the Nominal size, or body diameter is 1/2 inch (8mm metric thread diameter), the second number,16, represents the threads per inch, (distance between threads). The final number is the body length of the bolt or screw, 2 inches (50mm).

Torque Specification Chart

FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)


Hardware Grade

|

No Marks

SAE Grade 2

|

SAE Grade 5

|

SAE Grade 8

Size Of Hardware| in/lbs

ft/lbs

|

Nm.

| in/lbs

ft/lbs

|

Nm.

| in/lbs

ft/lbs

|

Nm.

8-32| 19| 2.1| 30| 3.4| 41| 4.6
8-36| 20| 2.3| 31| 3.5| 43| 4.9
10-24| 27| 3.1| 43| 4.9| 60| 6.8
10-32| 31| 3.5| 49| 5.5| 68| 7.7
1/4-20| 66| 7.6| 8| 10.9| 12| 16.3
1/4-28| 76| 8.6| 10| 13.6| 14| 19.0
5/16-18| 11| 15.0| 17| 23.1| 25| 34.0
5/16-24| 12| 16.3| 19| 25.8| 29| 34.0
3/8-16| 20| 27.2| 30| 40.8| 45| 61.2
3/8-24| 23| 31.3| 35| 47.6| 50| 68.0
7/16-14| 30| 40.8| 50| 68.0| 70| 95.2
7/16-20| 35| 47.6| 55| 74.8| 80| 108.8
1/2-13| 50| 68.0| 75| 102.0| 110| 149.6
1/2-20| 55| 74.8| 90| 122.4| 120| 163.2
9/16-12| 65| 88.4| 110| 149.6| 150| 204.0
9/16-18| 75| 102.0| 120| 163.2| 170| 231.2
5/8-11| 90| 122.4| 150| 204.0| 220| 299.2
5/8-18| 100| 136| 180| 244.8| 240| 326.4
3/4-10| 160| 217.6| 260| 353.6| 386| 525.0
3/4-16| 180| 244.8| 300| 408.0| 420| 571.2
7/8-9| 140| 190.4| 400| 544.0| 600| 816.0
7/8-14| 155| 210.8| 440| 598.4| 660| 897.6
1-8| 220| 299.2| 580| 788.8| 900| 1,244.0
1-12| 240| 326.4| 640| 870.4| 1,000| 1,360.0
NOTES

1.     These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.

2.     Recommended seating torque values for locknuts:

a.     for prevailing torque locknuts – use 65% of grade 5 torques.

b.     for flange whizlock nuts and screws – use 135% of grade 5 torques.

3.      Unless otherwise noted on assembly drawings, all torque values must meet this specification.

Common Hardware Types

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals