Digi Pas DWL-5800XY 2-Axis Inclination Sensor Module User Guide
- June 9, 2024
- Digi-Pas
Table of Contents
DWL-5800XY 2-Axis Inclination Sensor Module
User Guide
2-Axis Precision Sensor Module
DWL-5800XY
QUICK START GUIDE
DWL-5800XY 2-Axis Inclination Sensor Module
Calibration
Digi-Pas® device is calibrated in the factory for maximum accuracy.
Users can re-calibrate when necessary. for detail calibration please refer to
the Instruction manual available online
Cleaning
Do not use harsh chemicals, strong detergents or cleaning solvents to clean
the device.
Kit Contents
- Sensor module
- Sensor to DB-9 male cable
- RS422/485 serial converter *
- Female DB-9 lead cable
- Calibration Certificates
- Quick Guide
Note: 2 Converter driver available at digipaks website visit: https://www.digipas.com/5800xy
Safety Precautions
- Ensure the circular multipole plug align with the receptacle on the sensor module by following the locking guide.
- Secure the circular multipole plug by screwing it clockwise.
Direct serial RS422/485 connection diagram
Multiple sensor connection diagram using control box
DWL-5800XY PC sync software
DWL-5800XY Professional PC Sync Software is available for download at
digipas.com website.
PROFESSIONAL PC SYNC SOFTWARE & DRIVER: https://www.digipas.com/5800xy
SAMPLE CODE: https://www.digipas.com/samplecode
DWL-5800XY Instruction manual/Programing guide
Quick guide and instruction manual & device driver are available at Digi-Pas
website:
URL: hitps://www.digipas.com/manual5800xy
Connection Pin-out
Pinout of the circular multipole connector of the tilt sensor module 
Sensor DB-9 Male cable connector pin-out
| Pin No. | Description |
|---|---|
| 1 | GND |
| 2 | N.0 (No Connection) |
| 3 | GND (without Control Box) or Signal 1 (For Control Box only) |
| 4 | GND (without Control Box) or Signal 2 (For Control Box only) |
| 5 | Power Input (Regulated 9V DC) |
| 6 | RS485 – A (Non-inverting Receiver Input/Tx+) |
| 7 | RS485 – B (Inverting Receiver Input/Tx-) |
| 8 | RS485 – Z (Inverting Driver Output)/Rx-) |
| 9 | RS485 – Y (Noninverting Driver Output / Rx+) |
Technical Specification
| Dimension (mm) | 90 x 60 x 33 |
|---|---|
| Weight (Approx.) | 1200g |
| Power Voltage | 9V t1V DC |
| Output Mode | RS485 (full duplex) |
USB, RS232, and SPDT Relay.
Wireless Bluetooth connectivity (optional)
Waterproof Rating| IP65
Operating Temperature| 10°C to +40°C
Storage Temperature| -30°C to +80°C
Notes :
– Product specification and appearance ore subject to change for product
improvement without prior notice.
– *Control Box is required
Warranty
Digi-Pas® Digital level is warranted to the original purchaser to be free from
defects in workmanship and material. JSB Tech will, at its option, repair or
replace any defective part which may malfunction under normal and proper use
within a warranty period of 1 (one) year from the date of shipment. This one-
year warranty clause is NOT applicable to European Union (EU) member states.
Purchases made in EU member states will be covered by the existing consumer
laws across the European Union, which provide statutory warranty rights in
addition to the coverage of one year warranty period. The foregoing warranty
shall not apply to defects resulting from misuse, abuse, or transfer by the
Buyer, Buyer-supplied software or interfacing, or unauthorized modification or
operation outside of environmental specifications for the product. JSB Tech
does not warrant that the operation of the instrument software, or firmware,
will be uninterrupted or error-free. The exclusive remedy under any and all
warrants and guarantees expressed herein, and we shall not be liable for
damages from loss or delay of equipment uses, consequential, or incidental
damage. No other warranty is expressed or implied. JSB Tech specifically
disclaims the implied warranties of merchantability and fitness for a
particular purpose.
https://www.digipas.com/manual5800xy
JQC-2-05801-99-004
Technical Support
Email : info@digipas.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>