ideal lux SP11 Suspension Lamp Mapa Plus Pendant Light Instruction Manual

ideal lux SP11 Suspension Lamp Mapa Plus Pendant Light

Specifications

• Brand: Mapa Plus
• Model: SP11
• Max Wattage: 11 x 40W
• Voltage: 220-240V, 50/60Hz
• Color: Bianco (White)
• Manufacturer: IDEAL LUX s.r.l.
• Country of Origin: Italy

Product Usage Instructions

• The lighting fitting should be installed by a qualified electrician.
• Follow the assembly instructions in numerical order.

Safety Instructions

• Always disconnect the power supply before installation or maintenance.
• Avoid looking directly at the light source.
• Ensure the external electric cable is replaced only by the manufacturer, retailer, or a qualified electrician if damaged.
• Use appropriate fixing accessories and comply with regulations for installation.
• If the lamp does not turn on, replace the fuse.

Electrical Safety Classes

• Class I: Mandatory grounding with electrical safety ensured by main insulation and a protective conductor connected to the lamp’s metal structure.
• Class II: Electrical safety ensured by main insulation and double insulation or reinforced insulation. No grounding is required.
• Class III: Electrical safety is ensured by a very low voltage supply (less than 50 Volts). No grounding is required.

IP Ratings

• The product has different IP ratings indicating protection against solid particles and moisture.
• Please refer to the manual for specific details.

FAQ

• Q: Can I replace the LED light source?
• A: The LED light source in this product is non-replaceable. Do not disassemble the unit.
• Q: What should I do if the lamp does not turn on?
• A: Check and replace the fuse if needed. If the issue persists, consult a qualified professional for further assistance.

Mapa Plus SP11

• Suspension lamp
• E14 max 11 x 40W / 220~240V 50/60Hz
  • 8021696131924 BIANCO

Features

Dimension

Installation Instructions

• FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
• THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).

2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.

3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.

4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.

5. Always isolate power before commencing installation, maintenance or repair.

6. The luminaire contains certain parts which can be very hot.

7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.

8. Always tighten the screws firmly to avoid contact problems.

9. This fitting should only be installed indoors.

10. Luminaires are not suitable for recessed on normally flammable surfaces.

11. Luminaire is not suitable for direct mounting on normal flammable surfaces.

12. This fitting is only suitable for fixing to the ceiling.

13. This fitting is only suitable for fixing to the wall.

14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.

15. Only use lamps that do not exceed the maximum specified wattage.

16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.

17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.

18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.

19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.

20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.

21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.

22. Class IL electrical safety is guaranteed by the main insulation and double or reinforced insulation.
    Earthing is not necessary.

23. Class III Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.

24. Not Protected

25. Protected against solid objects greater than 50 mm.

26. Protected against solid objects greater than 12 mm.

27. Protected against solid objects greater than 2,5 mm.

28. Protected against solid objects greater than 1mm.

29. Dust protected.

30. Protected against dust infiltration.

31. Not Protected

32. Protected against vertically falling water drops.

33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.

34. Protected against rain.

35. Protected against splashing water.

36. Protected against water jets.

37. Protected against strong water jets.

38. Protected against temporary immersion.

39. Protected against prolonged immersion.

40. The luminaire was not suitable for covering with thermally insulating material.

41. Caution, risk of electric shock.

42. Do not stare at the operatina light source.

CONTACT

IDEAL LUX s.r.l.

• Via Taglio Destro 32
• 30035 Mirano (VE) Italy
• www.ideal-lux.com

IDEAL LUX Warehouse

• Via delle Industrie, 8/D
• 30036 Santa Maria di Sala (Venezia)
• 8.00 – 12.00 / 13.30 – 17.00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>