ideal lux Firenze AP2 Firenze Indoor Wall Light 2Lt Instruction Manual

ideal lux Firenze AP2 Firenze Indoor Wall Light 2Lt

Product Specifications

• Model: Firenze AP2
• Socket Type : E14
• Maximum Wattage : 2 x 40W
• Voltage: 220~240V, 50/60Hz
• Dimensions: 380mm x 330mm x 170mm
• Color Options : BIANCO (8021696012902), ORO (8021696020846)

Product Usage Instructions

Installation Guidelines:

Before starting the installation process, please ensure that the following steps are followed:

1. Read the assembly instructions carefully by following the numerical progression provided.
2. The lighting fitting should be installed by a qualified electrician for safety reasons.

Safety Instructions:

For safe operation and maintenance of the product, adhere to the following safety guidelines:

• Always consult local authorities regarding proper disposal methods.
• Ensure that installation is carried out by a qualified electrician according to regulations.
• Replace any damaged external electrical cables only with those provided by the manufacturer, retailer, or a qualified electrician.
• Disconnect the power supply before starting any installation or maintenance procedures.
• Avoid touching hot surfaces on the product.
• Use appropriate fixing accessories specific to the materials involved.
• Do not disassemble the LED light source as it is non-replaceable.
• If the lamp does not turn on, replace the fuse with a new one.
• Ensure proper electrical safety with grounding as required for Class I and Class II devices.

Protection Classes:

The product conforms to various protection classes for electrical safety:

Class I : Grounding mandatory

• Class II : Double insulation, no grounding required
• Class III : Safety ensured by low voltage, no grounding required

Dust and Solid Particle Protection:

The product offers different levels of protection against solids and dust:

• Protected against solid bodies larger than 50mm (IP0…)
• Protected against solid bodies larger than 12mm (IP5…)
• Protected against solid bodies larger than 2.5mm (IP1…)
• Protected against solid bodies larger than 1mm (IP2…)
• Fully protected against dust ingress (IP…0)

FAQ

• Q: Can the LED light source be replaced?
  • A: No, the LED light source is non-replaceable. Do not attempt to disassemble it.
• Q: What should I do if the lamp does not turn on?
  • A: In case of a non-functioning lamp, try replacing the fuse with a new one.
• Q: Is grounding mandatory for this product?
  • A: Grounding is mandatory for Class I devices to ensure electrical safety.

FEATURES

Wall lamp

• E14 max 2 x 40W / 220~240V 50/60Hz
• 8021696012902 BIANCO
• 8021696020846 ORO

DIMENSIONS

INSTALLATION

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED.

PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE. 1

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards.
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing not necessary.
23. Class III Electrical safety is guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. The luminaire was not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL LUX s.r.l.

• Via Taglio Destro 32 30035 Mirano (VE) Italy
•   www.ideal-lux.com

IDEAL LUX Warehouse

• Via delle Industrie, 8/D 30036 Santa Maria di Sala (Venezia)
• 8.00 – 12.00 / 13.30 – 17.00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>