ideal lux Pegaso SP3 Pendant Light 3Lt Instruction Manual

ideal lux Pegaso SP3 Pendant Light 3Lt

Specifications

DIMENSION

Installation Instructions

The installation must be completed by a qualified electrician. Follow the assembly instructions by reading the numerical progression.

1. Ensure that the power supply is switched off before beginning installation.
2. Use appropriate mounting accessories for the material to which the lamp will be fixed. The included accessories may not be suitable for all types of surfaces.
3. The lamp should only be used with E14 bulbs and should not exceed the maximum specified wattage.
4. Maintain the minimum safety distance between the lamp and the surface below as indicated in the instructions to prevent fire hazards.
5. After installation, ensure that the lamp is securely fastened to avoid falling.

Safety Instructions

This fitting is produced and tested in accordance with the relevant European safety standards (EN 60598-1). It cannot be disposed of as household waste. For disposal, please contact your local authorities.

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).

2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.

3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.

4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.

5. Always isolate power before commencing installation, maintenance or repair.

6. The luminaire contains certain parts which can be very hot.

7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.

8. Always tighten the screws firmly to avoid contact problems.

9. This fitting should only be installed indoors.

10. Luminaires not suitable for recessed on normally flammable surfaces.

11. Luminaire not suitable for direct mounting on normal flammable surfaces.

12. This fitting is only suitable for fixing to the ceiling.

13. This fitting is only suitable for fixing to the wall.

14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.

15. Only use lamps which do not exceed the maximum specified wattage.

16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.

17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.

18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.

19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.

20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.

21. Class I Electrical safety guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.

22. Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation.
    Earthing not necessary.

23.  Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.

24. Not protected.

25. Protected against solid objects greater than 50 mm.

26. Protected against solid objects greater than 12 mm.

27. Protected against solid objects greater than 2,5 mm.

28. Protected against solid objects greater than 1mm.

29. Dust protected.

30. Totally protected against dust infiltration.

31. Not protected.

32. Protected against vertically falling water drops.

33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.

34. Protected against rain.

35. Protected against splashing water.

36. Protected against water jets.

37. Protected against strong water jets.

38. Protected against temporary immersion.

39. Protected against prolonged immersion.

40. Luminaire not suitable for covering with thermally insulating material.

41. Caution, risk of electric shock.

42. Do not stare at the operating light source.

FAQ

What type of bulbs does the Pegaso SP3 use? The lamp uses E14 bulbs with a maximum wattage of 28W each. Can the Pegaso SP3 be installed outdoors? No, the Pegaso SP3 is designed for indoor use only and has an IP20 rating. What should be done if the external electrical cable is damaged? The cable must be replaced exclusively by the manufacturer, distributor, or a qualified electrician. Is it necessary to disconnect the power supply before installation or maintenance? Yes, always disconnect the power supply before beginning installation or any maintenance work.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>