ideal lux Marte PT1 Bollard Light 1Lt in Anthracite Instruction Manual

ideal lux Marte PT1 Bollard Light 1Lt in Anthracite

Product Information

• Specifications
  • Model: Marte PT1
  • Socket Type: E27
  • Maximum Wattage: 1 x 25W
  • Voltage: 220-240V, 50/60Hz
  • Colour: Anthracite
  • Manufacturer: IDEAL LUX s.r.l.
  • Dimensions: 140mm x 140mm

Product Usage Instructions

• Ensure the lighting fixture is installed by a qualified electrician.
• Follow the assembly instructions provided in numerical order.
• Before starting the installation or any maintenance, always disconnect the power supply.
• Use appropriate screws and anchors for mounting the fixture securely.
• If the lamp fails to light up, replace the fuse.
• Grounding is mandatory for electrical safety.
• Avoid looking directly at the light source.
• Do not disassemble the LED light source as it is non-replaceable.

FAQs

• Q: How do I replace the fuse in the lamp?
  • A: If the lamp does not turn on, locate the fuse compartment, open it, and replace the fuse with a new one of the same rating.
• Q: Can I use a higher-wattage bulb with this fixture?
  • A: It is recommended to adhere to the maximum wattage specified (1 x 25W) to prevent overheating and potential damage to the fixture.
• Q: Is grounding necessary for this lighting fixture?
  • A: Yes, grounding is essential for electrical safety as specified in the safety instructions. Please ensure proper grounding during installation.

DIMENSION

FEATURE

ASSEMBLY INSTRUCTIONS

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires are not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
22. Class II Electrical safety is guaranteed by the main insulation and a double or reinforced insulation. Earthing is not necessary.
23. Class III Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire is not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

CONTACT

• IDEAL LUX s.r.l.
• Via Taglio Destro 32
• 30035 Mirano (VE) Italy
• www.ideal-lux.com.
• REV 18/10/2023

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>