METROPOLITAN N7326-613 Luxour 6-Light Polished Nickel Pendant Instruction Manual

: June 12, 2024
: Metropolitan

Table of Contents

METROPOLITAN N7326-613 Luxour 6-Light Polished Nickel Pendant
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTION
ASSEMBLING THE FIXTURE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

METROPOLITAN N7326-613 Luxour 6-Light Polished Nickel Pendant

Product Information

The product model is N7326-613. It is a lighting fixture that requires installation and wiring. The fixture is designed to accommodate up to six candelabra base bulbs with a maximum wattage of 60 watts each. The fixture also supports CFL or LED equivalent bulbs.

Product Usage Instructions

Before starting the installation, ensure that the power is shut off at the fuse box or circuit breaker.
Remove the old fixture and all mounting hardware from the junction box.
Unpack the new fixture and lay out all the parts on a clear area, taking care not to lose any necessary parts.
Thread the stem (M) onto the all thread (N).
Determine the desired hanging height and thread rods (H, I, J, K) to the coupling (L). Then thread the swivel (G) of the canopy (E) onto rod (H). Pass wires carefully through each rod, swivel (G), and canopy (E).
Thread the two mounting screws (A) into the crossbar (B) spaced the same distance apart as the holes in the canopy (E). Secure the crossbar (B) to the junction box with junction box screws (C). Ensure that the side of crossbar (B) marked GND faces out.
Attach the hook (D) on the end of the support cable to the crossbar (B). Allow the support cable to support the weight of the fixture while wiring.
Connect the electrical wires as shown in figure 2, ensuring that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (B) using the green screw provided.
Tuck wire connectors neatly into the junction box.
Align the canopy (E) to the mounting screws (A) and secure it with cap nuts (F).
Secure the finial (P) onto the all thread (O).
Hook the crystal drop (Q) to the finial (P).
Install up to six candelabra base bulbs up to 60 watts each or CFL or LED equivalent bulbs (not included) according to the fixture specifications. Do not exceed the specified wattage.
Once the installation is complete, return power to the junction box and test the fixture.

Hardware Bag:

A. Mounting Screws *2
B. Crossbar *1
C. Junction Box Screws *2
E. Canopy *1
F. Cap Nuts *2

INSTALLATION INSTRUCTION

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPATION

ASSEMBLING THE FIXTURE

(Fig.1)

Shut off the power at the fuse box or circuit breaker box. Remove old fixture and all mounting hardware from junction box.
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any parts necessary for installation.
Thread stem (M) onto all thread (N).
Determine desired hanging height and thread rods (H, I, J, K) to coupling (L). Then thread swivel (G) of canopy (E) onto rod (H). Pass wires carefully through each rod, swivel (G) and canopy (E).
MOUNTING THE FIXTURE (Fig.1
Thread the two mounting screws (A) (Size: #8 321.2″L) into the crossbar (B) spaced same distance apart as the holes in canopy (E). Secure crossbar (B) to junction box (not provided) with junction box screws (C) (Size: #8-320.6”L). The length of mounting screws (A) into crossbar (B) may be adjusted if necessary. The side of crossbar (B) marked “GND” must face out.
The support cable is provided to support the weight of the fixture while wiring. Attach the hook (D) on the end of the support cable to the crossbar (B).
Carefully allow the support cable to support the weight of the fixture while wiring.
CONNECTING THE WIRES (Fig.2)
Connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the crossbar (B) using the green screw provided.
Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
Align canopy (E) to mounting screws (A) and secure with cap nuts (F).
Secure finial (P) onto all thread (O).
Hook crystal drop (Q) to finial (P).
Install (6) six candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. (DO NOT EXCEED THE SPECIFIED WATTAGE!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)