Metropolitan N7813-726 Soho 4 Light Coal and Soft Brass Cage Pendant Light Instruction Manual
- October 30, 2023
- Metropolitan
Table of Contents
Metropolitan N7813-726 Soho 4 Light Coal and Soft Brass Cage Pendant
Light
Product Information
The product is a light fixture with item number N7813-726, manufactured on May 11, 2022. The fixture comes with a metal tube, fixture body, mounting plate, canopy, glass panel, medium base bulbs (not included), and necessary screws and rods. It has a maximum wattage rating of 60 watts per bulb or CFL or LED equivalent.
Product Usage Instructions
- Before beginning installation, shut off power at the fuse box or circuit breaker box.
- Remove the old fixture including the mounting hardware.
- Unpack the new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
- Place the metal tube over the fixture body and secure with screws.
- Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck wire connectors neatly inside the junction box.
- Align the canopy onto the mounting plate and secure with screws.
- Place the glass panel into the metal frame and secure with tabs provided.
- Install four medium base bulbs (not included) up to 60 watts each or CFL or LED equivalent in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- Turn on power at the fuse box or circuit breaker box and test the fixture.
INSTALLATION INSTRUCTIONS
Item#N7813-726 (New. 2022/05/11)
READ AND SAVE THESE INSTRUCTIONS
WARNING
SHUT POWER OFF ATF USE OR CIRCUIT BREAKER .
AVERTISSEMENT!
COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
ASSEMBLING THE FIXTURE (Fig. 1) -
Place metal tube (Z) over fixture body (K) and secure with screws (Y). Place metal frame (H) over metal tube (Z) and secure with screws (X).
-
Secure rod (J) onto all thread (T) on fixture body (K) and place metal ring (Q) over rod (J).
-
Secure rod (V) onto rod (J).
-
Determine the desired hanging height and thread rods (F1, F2 and F3) to rod (V). Carefully pass wires through each rod during assembly.
-
Align canopy (E) and metal plate (P) followed by lock washer (O) and metal washer (N) onto all thread of rod (F1) and secure with hex nuts (M) via Wrench (U) (not included).
-
Position mounting plate (B) one ceiling and mark location of the three mounting holes. Drill holes on ceiling and insert plastic anchors (A).
-
Attach mounting plate (B) to junction box (Not included) with mounting screws (C) (Size: #8-32N*L0.5”) and wood screws (D) into drywall anchors (A). The side of mounting plate marked “GND” must face out.
-
The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (B) and attach hook (R) on end of support cable (S) into a slot located on mounting plate (B). Carefully allow support cable (S) to support the weight of fixture while wiring.
CONNECTING THE WIRES (Fig. 2)
-
Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using green screw provided. Tuck wire connectors neatly inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1) -
Align canopy (E) onto mounting plate (B) and secure with screws (L).
-
Place glass panel (G) into metal frame (H) and secure with tabs provided.
-
Install (4) four medium base bulbs (I) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification
DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test fixture.
Note
Illustration (Fig.1) on this manual is for installation purposes only. It
may or may not be identical to the fixture purchased.
LA-3543E
Documents / Resources
|
Metropolitan N7813-726 Soho 4 Light Coal and Soft Brass Cage Pendant
Light
[pdf] Instruction Manual
N7813-726 Soho 4 Light Coal and Soft Brass Cage Pendant Light, N7813-726, Soho
4 Light Coal and Soft Brass Cage Pendant Light, Brass Cage Pendant Light, Cage
Pendant Light, Pendant Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>