VOLLRATH T3871260 Cafeteria Breath Guard Instruction Manual

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH T3871260 Cafeteria Breath Guard
Product Usage Instructions
Installation Instructions
three Piece Breath Guard installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH T3871260 Cafeteria Breath Guard

Specifications :

Brand: Vollrath
Model: Cafeteria Breath Guard
Types: One Piece, Three Piece
Item No.: 2350030-01 Rev 04/12

Product Usage Instructions

One Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.

Three Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C). Repeat on the other side.
Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

FAQ :

Q: What should I do if I accidentally over tighten the cap nuts?
A: If you accidentally over tighten the cap nuts, stop immediately to prevent cracking of the plastic. Loosen the cap nuts slightly until they are secure without causing any damage.
Q: Can I disassemble the breath guard for cleaning?
A: Yes, you can disassemble the breath guard following the reverse steps of the installation instructions. Make sure to clean each component thoroughly before reassembling.
Q: Are additional mounting accessories included in the package?
A: The package includes all necessary mounting accessories required for installation. No additional accessories are included.

Installation Instructions

One Piece cafeteria Breath Guard three Piece cafeteria Breath Guard

These instructions cover the installation of the one pica Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:

Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
Figure 1. One Piece Breath Guard Installation
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.

three Piece Breath Guard installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
Figure 2. Three Piece Breath Guard Installation
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.