Patpet T330 Training Collar User Manual

June 13, 2024
PATPET

Patpet T330 Training Collar

Please read this manual carefully before use

Safety Instructions

  1. This product cannot be tested directly on humans, otherwise it will violate local laws.
  2. Turn off or remove the receiver before playing with the dog.
  3. Please do not wear the receiver on your dog for a long time.
  4. Do not place the product near a stove or at high temperatures.
  5. Do not open the shell of the product, which will cause the lithium battery disconnect or fire.

1| This product cannot be tested directly on humans, otherwise it will violate local laws.|

---|---|---
2| Turn off or remove the receiver before playing with the dog.|
3|
Please do not wear the receiver on your dog for a long time.|
4| Do not place the product near a stove or at high temperatures.|

5| Do not open the shell of the product, which will cause the lithium battery disconnect or fire.| ****

Product Introduction

Thank you for choosing our products. The T330 dog training collar has a transmission range of 330 yards. When you start the punishment function on the remote control, your dog will receive stimulation from the electronic collar (such as beep, vibration and static stimulation). Collar and contact points are designed in an integrated way, which is waterproof (IPX7) and friction resistant. It is suitable for small, medium and large dogs, and has been proved safe, reliable and effective by dog trainers.

What You Get

COMPONENTS Quantity
Transmitter 1
Receiver (Including collar) 1
Static stimulation test light 1
Magnetic charging cable 1
Lanyard 1
User Manual for T330 Remote Training Collar 1

COMPONENTS

| Transmitter| 1
| Receiver (Including collar)| 1
| Static stimulation test light| 1
| Magnetic charging cable| 1
| Lanyard| 1
| User manual| 1

 Function and Operation Description

At a glance

Patpet -T330 -Training -Collar - 12

Patpet -T330 -Training -Collar - 13

Patpet -T330 -Training -Collar - 15

Battery Status CH1 CH2 Lock/Unlock Tone Icon Vibration Icon Static Stimulation Icon Vibration/Static Stimulation Level Charging Port Contact Point TPU Adjustable Collar Charging Port Please tie the lanyard here Used to adjust the level of Static Stimulation / Vibrate Used to display device status Switch to Lock or Unlock Press to start the tone function Press to start the vibration function Static Stimulation Button Press to start the static stimulation function Channel Selection Button Used to switch other receiver communication channels Press to turn on/off the receiver

Lanyard Hole Please tie the lanyard here
Level+/- Button Used to adjust the level of Static Stimulation / Vibrate
Display Screen Used to display device status
Lock/Unlock Switch to Lock or Unlock
Tone Button Press to start the tone function
Vibration Button Press to start the vibration function
Static Stimulation Button Press to start the static stimulation function
Channel Selection Button Used to switch other receiver communication

channels
⑨| On/Off Button| Press to turn on/off the receiver

Receiver Indicator Light Status

Light Color Status
 Red light (Flashing slowly) Charging
Steady green light Charging completed
Green light Blinks every 5 seconds Receiver is power on
Green light Flashes once Tone
Yellow light Flashes once Vibration
Red light Flashes once Static Stimulation

Charging
Tips: Please fully charge before use!
It takes about 2 hours for full charging DC5V1A The indicator flashes red when charging The indicator stays green after full charging DC5V1A

Patpet -T330 -Training -Collar - 19

Turn on/off: Transmitter and Receiver
Slide down to lock the transmitter The startup indicator color is green. Long press 2 seconds to turn on/off Slide up to unlock the transmitter The indicator color is red when the device is powered off.

Patpet -T330 -Training -Collar - 20

Function Introduction

Tone:

Patpet -T330 -Training -Collar - 21

Transmitter delivers a beep tone with nonadjustable volume to the receiver collar.

Vibration:

Patpet -T330 -Training -Collar - 22

Press + / – firmly to adjust the vibrate level Transmitter delivers a vibrate with adjustable level (level1-16) to the receiver.

Static Stimulation:

Patpet -T330 -Training -Collar - 23

Press + / – firmly to adjust the Static Stimulation level Transmitter delivers a static stimulus with adjustable level (level1-16) to the receiver collar. The indicator color shows red.

How to test the Static Stimulation function

Patpet -T330 -Training -Collar - 24

  1. Step 1: Make sure the Transmitter and receiver collar are paired.
  2. Step 2: Start the static stimulation function and adjust the level to 10.
  3. Step 3: Put the test light between two contact points and make sure its interface is touching the contact points. Press the static stimulation button again, if the test light is on which means the static stimulation is ongoing.

Pairing and select the communication channel:
Tips: The default factory settings of the communication channel is channel 1.

  • Step 1: Unlock the transmitter and long press the button to select a signal channel.

Patpet -T330 -Training -Collar - 25

  • Step 2 :Make sure the receiver is shut down first, and hold on the on/off button for 7 seconds. The green light will flash quickly and enter to the matching state after hearing a beep.Patpet -T330 -Training -Collar - 26
  • Step 3: Please press the tone or vibration function button within 10 seconds when entering the matching state, and the receiver will beep twice indicating that the matching is successful.

Note:

  1. Repeat above steps when timeout
  2. One channel can control multiple receivers simultaneously

Wearing Method And Precautions

Wearing Method

①| Please keep the dog in a comfortable standing position and ensure that the receiver is turned off before wearing.|
---|---|---
②| Please place the receiver in the middle of the dog’s neck and ensure that the direction of the switch button is upward, and the contact point is aligned with the dog’s throat. Check the tightness of the receiver collar.|
③| The wearing standard is that a finger can be held between the collar and the dog’s neck. If the collar is too loose or tight, the normal operation of the product will be affected.|
④| Mark the length of the collar with a pen, remove the collar and cut off the excess part, and slightly burn the edge with a lighter to prevent the thread from falling off.|

Wearing Precautions

  • Wearing a collar for a long time or too tight will cause the dog’s skin to be worn, from redness to pressure sores.
    This condition is often referred to as bedsore.

  • Please make sure your dog doesn’t wear the collar more than 12 hours a day.

  • Please try to readjust the collar position on the pet’s neck every 1 to 2 hours.

  • Regularly check the tightness of the collar to prevent excessive pressure.

  • Do not connect the tow rope to the receiver, or excessive pressure will be caused to the collar.

  • Please clean your pet’s neck area and the contact area of the receiver with a damp cloth every week.

  • Please check the contact area daily for signs of rash or pain.

  • Please stop using the collar until the skin heals if you notice a rash or pain in your dog. If the condition persists for more than 48 hours, seek medical attention immediately.

Frequently Asked Questions

Questions Analysis Measures
1. Remote/receiver cannot be charged Charging cable is not fit Use the

5V1A original charging cable
Charging cable is damaged| Replace the charging cable and try again
The product low power enters the low power protection mode| The battery needs to be activated. Please extend the charging time slightly
2. The product does not turn on| Check whether the touch of the key is normal| No response means damaged
---|---|---
No display/sound prompt| Recharge again
The product low power enters the low power protection mode| Recharge and wait for the battery to activate
Wrong startup method| Long press the on/off button
3. No static stimulation /No vibration| The shock level is set 0, or the shock level is too low| Adjust high shock level and try again
The vibration level is set 0, or the vibration level is too low| Adjust high vibration level and try again
Check whether the battery is low and the output power becomes small| Charge the receiver in time
The dog hair not well groomed| The contact points are attached to the dog’s skin
The collar strap is wearing too loose| The receiver is worn in the middle of the dog’s neck, with a finger width gap between the collar and the neck
Remote & receiver not paired| Repair the remote with receiver
4. The collar strap is easy to fall off and not tight| The collar strap is wearing too loose| The receiver is worn in the middle of the dog’s neck, with a finger width gap between the collar and the neck
---|---|---
Excess collar strap not cut off after first-time wear product| Collar straps should be passed through each buckle, and excess collar straps should be cut off and clamped to the size of the dog’s neck
The collar strap is damaged and needs to be replaced| Please refer to page 6 for instructions on wearing the collar
5. The remote screen displays garbled characters| Low battery power| Use it after it is fully charged
Violent handling and beating. The transmitter was damaged by a dog.|

  1. the use of the process can not be violent operation, artificial damage will not be after-sales; Keep the transmitter and receiver out of sight of the dog when in and out of use.
  2. In case of garbled characters on the display screen after receiving the goods, contact customer service for confirmation after shooting video or pictures

6. Dog injuries| Wear it for too long time| It should not be worn for more than 12 hours and should be checked every 2 hours
---|---|---
Worn when the dog’s hair is wet or swimming, the shock column will wear on the skin|

  1. Keep your dog’s neck area dry and clean, and do not wear products while swimming or playing with your owner
  2. Use silicone caps to reduce the friction of the contact points

Dog has skin diseases| Stop using the product for a few days. If the condition persists for more than 48 hours, consult your veterinarian for help
The dog is less than 6 months old| The pet should be at least 6 months old before using the training collar, and the dog should be able to recognize basic obedience commands, such as “sit” or “stay.”
7. Accessories missing, accessories damage, etc| Transport damage or packing miss| Contact customer service to confirm the repair/return with shooting video or photos.
8. Product compatibility issues| The remote and receiver need to match, if buy another sellers’ remote or receiver, it can not be paired with ours| Buy the same model from us to pair
---|---|---
9. Safety of vibration/shock| A brief vibration or shock won’t hurt, but it can make the dog feel uncomfortable| The continuous use of vibration and shock should not exceed 30 seconds. The dog training collar requires the user to interact with and train the pet to achieve the desired effect
Our vibration and shock functions have been tested on different types of dogs over a long period of time
10. Remote range does not equal actual| The actual remote range may vary due to terrain, weather, vegetation, battery capacity, and interference from other radio devices.| Change the venue and try to train in a place with less interference
11. The product does not effect| The dog training collar is a training aid product, which requires users to interact and train their pets to achieve the desired effect|

  1. Seek training support from a professional dog trainer
  2. Proper training time. The training course should be kept active and short, with a better effect of about 10-15 minutes each time

12. It is effective at first, but does not work later|

  1. Check whether the device works normally
  2. Wearing for a long time dog has been fully adapted

|

  1. Change the levels and readjust the training mode
  2. It is recommended not to wear the product when not training

---|---|---
13. The product does not work| Can not turn on it| Test after charging
Remote & receiver not paired well| Repair the remote with receiver
14. Dog bites damage the device/collar belt| The dog resists the product| Do not let the dog see when wearing and operating the product
15. Do not use the product for a long time| If the product is not used for a long time, it will lose power until it is shut down.|

  1. Please turn it off every time when not using it
  2. If it is not used for a long time, please refer to the manual for charging instructions before charging it and use

About After-Sales

  1. If the product is faulty within 30 days from the purchase date, you need to take a video or picture of the faulty product. After the customer service confirms, the replacement can be sent. And the faulty product must be returned within 7 days after receiving the replacement.
  2. If the product is faulty after 30 days, and it is still within the 1-year warranty period from the purchase date, the consumer will be required to return the product and pay the freight. We will test and replace the faulty parts, and returned to you free of charge.
  3. This warranty is a supplement to other rights and remedies provided by law. For major failures and any other compensation, i f it is a reasonably foreseeable loss or damage, you are entitled to a replacement or refund.
  4. You also have the right to repair or replace the goods in the following cases: the quality of the goods is unqualified, and the failure does not constitute a major failure. If you have any questions or need more information, please contact our customer service.

Compliance

  • This symbol means that the product has been CE certified, and any product with CE mark is proved in compliance with the local regulations of EEAs.
  • This symbol means that the electromagnetic interference of the equipment is lower than the limit approved by the Federal Communications Commission.
  • Disposal of package: The package shall be disposed by type. Disposed as waste papers for cardboards and cartons Recycling for packaging cases
  • Disposal system: The disposal system shall be applicable to EU and other European countries and capable of collecting recyclable materials by category.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals