Dynojet Power Commander 6 Husqvarna TE630-SMS 630 2011-2012 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
Power Commander 6 Husqvarna TE630-SMS 630 2011-2012
Installation Guide
PARTS LIST
| 1 POWER COMMANDER 6 | 2 POWER COMMANDER DECALS |
|---|---|
| 1 INSTALLATION GUIDE | 2 VELCRO STRIPS |
| 1 USB CABLE | 1 ALCOHOL SWAB |
| 2 DYNOJET DECALS | 1 POSI-TAP |
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
IPC6-23008.01
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fly between these two base maps when you hook up a switch to the
MAP inputs. You can use any open/close type switch. The polarity of the wires
is not important.
Shifter
(Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is set up
you can alter your map based on gear position and setup gear-dependent kill
times when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you
will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seat.
-
Remove the fuel tank.
-
Using the supplied Velcro, attach the PC6 module to the inner side of the right-hand side cover. Clean both surfaces with the supplied alcohol swab before attaching the Velcro.
-
Attach the PC6 ground wire with the small ring lug to the negative (-) terminal of the bike’s battery.
-
Route the PC6 wiring harness towards the throttle body, going underneath the frame support.
-
Unplug the stock wiring harness from the fuel injector.
-
Plug the PC6 wiring harness in-line of the fuel injector and the stock wiring harness.
-
Using the supplied Posi- tap, attach the GREY wire from the PC6 to the stock ORANGE/BLACK wire of the main wiring harness.
-
This is the 3rd wire from the end, on the top row of the ECU connector. 9 Reinstall the fuel tank and the seat.
Download the latest map files
from our website at dynojet.com/tunes.
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –
800-992-4993 –
DYNOJET.COM
© 2011-2021 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>