hlins HD-250 Shock Absorber Harley Davidson Pan America Instruction Manual
- June 1, 2024
- HLINS
Table of Contents
HD-250 Shock Absorber Harley Davidson Pan America ** Instruction Manual**
HD-250 Shock Absorber Harley Davidson Pan America
Kit Contents
Description| Part No| Pcs
Shock absorber| HD250| 1
Tie rap| 00231-01| 2
Sticker set| 10207-01| 1
Sticker Memo notes| 01180-01| 1
Owner´s manual| 07241-02| 1
Note!
Please note that there can be small differences between your product and the
images in these instructions.
Note!
Please note that during storage and transport, especially at high ambient
temperature, some of the oil and grease used for assembly may leak and stain
the packaging. This will not cause damage to the product, wipe off the
excessive oil or grease with a cloth.
**Note!
Before you install this product, check the kit contents. If anything is
missing, please contact an Öhlins dealer.
Warning!**
Before you install this product, read the Öhlins Owner’s manual. This product
is an important part of the vehicle and the vehicle stability.
Shock absorber for Harley-Davidson Pan America 1250
HD 250
Mounting Instructions
MOUNTING INSTRUCTIONS
Warning!
We strongly recommend to let an Öhlins dealer install this product.
Warning!
If you work with a lifted vehicle, make sure that it is safely supported to
prevent it from tipping over.
Note!
When you work with this product, see the vehicle service manual for vehicle
specific procedures and important data.
Note!
Before you install this product clean the vehicle.
-
Put the motorcycle on a work stand so that the rear wheel is up in the air and put a support under the rear wheel.
-
Refer to the manufacturer’s user manual and carry out measures to lift the subframe slightly. This allows the original shock absorber to be removed.
-
Remove the lower shock absorber screw.
-
Remove the upper shock absorber screw.
Lower the swing arm and remove the shock absorber. -
Mount the Öhlins shock absorber in reverse order.
-
Using the original screws, mount the hydraulic preload master cylinder on the inside of the fotpeg mount.
-
Use supplied Tie-raps (00231-01) to fasten the hose.
-
Before riding the bike, check that all screws are tightened correctly and that there are no clearance issues when the rear suspension is moving.
ADJUSTMENTS
Warning!
Before you ride/drive, always make sure that the setup is according to the
recommended setup data. Read about adjustments and setting up in the Öhlins
Owner’s Manual before you make any adjustments. Contact an Öhlins dealer if
you have any questions about setting up.
SETUP DATA
| Length | 398,5 | mm |
|---|---|---|
| Stroke | 80 | mm |
| Rebound | 12 | clicks |
| Compression | 12 | clicks |
| Spring (part.no.) | 00698-34 | |
| Spring preload | 12 +10/-0 | mm |
| Spring rate | 100 | N/mm |
| Spring free length | 230 | mm |
Recommended Free sag and Ride height’
| R1-R2 | mm | |
|---|---|---|
| R1-R3 | 72 | mm |
| F1-F2 | mm | |
| F1-F3 | 59 | mm |
Öhlins products are subject to continuous improvement and development,
therefore, although these instructions include the most up-to-date information
available at the time of printing, minor updates may occur.
To find the latest information contact an Öhlins distributor.
Please contact Öhlins if you have any questions regarding the contents in this
document.
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use
without the written permission of Öhlins Racing AB is prohibited.
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
Part no. MI_HD250_0
Issued 2023-12-21
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>